foratvise
Loslegen
Anlagenausfall (Störungen)

Belt drive / transmission shaft failure

Anlagenausfall (Störungen)VerfügbarkeitMahlen und Zerkleinern

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei etwa 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 58 % der Verlustzeit der Linie. Berichtet von 1 der 43 Studien, die sie beobachten konnten (spärliche Evidenz).

Was passiert

The belt drive transmits rotary power from the motor to the milling rolls or shaft; wear, misalignment, excessive tension, fatigue or contamination causes the belt to crack, slip or snap, and the associated transmission shaft or belt cover can crack or deform under the same stresses. Loss of power transmission stops or degrades the mill until the belt, shaft or cover is repaired or replaced.

Was man dagegen tut

Apply condition-based maintenance with periodic belt tension, alignment and wear inspection, vibration and thermal monitoring of the drive shaft, and scheduled replacement of belts, shafts and covers based on condition rather than failure; protect the belt cover from impact and keep it properly guarded.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
0,9 % [0,2–2,7 %]
Erwarteter Anteil an der Verlustzeit
0,5 % [0,1–1,6 %]
Anteil an der Verlustzeit bei Auftreten
58 % [47–68 %]
Studien / Einheiten
43 / 48
Evidenzgrad
D

Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    1,1 % [0,1–4,3 %]5 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    1,1 % [0,1–4,4 %]1 Studie
  • Bier, Wein und Spirituosen
    1,1 % [0,1–4,4 %]0 Studien
  • Backwaren und Teigwaren
    1,1 % [0,1–4,4 %]0 Studien
  • Fleisch, Geflügel und Fisch
    1,1 % [0,1–4,6 %]0 Studien
  • Obst- und Gemüseverarbeitung
    1,1 % [0,1–4,4 %]2 Studien
  • Getreide- und Ölsaatenmüllerei
    1,1 % [0,1–4,1 %]7 Studien
  • Zucker und Süßwaren
    1,0 % [0,1–3,9 %]10 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    1,5 % [0,2–5,7 %]5 Studien
  • Futtermittel und Heimtiernahrung
    1,1 % [0,1–4,3 %]6 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    1,1 % [0,1–3,9 %]7 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

The belt drive transmits rotary power from the motor to the milling rolls or shaft; wear, misalignment, excessive tension, fatigue or contamination causes the belt to crack, slip or snap, and the associated transmission shaft or belt cover can crack or deform under the same stresses. Loss of power transmission stops or degrades the mill until the belt, shaft or cover is repaired or replaced.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

SCADA/MES shows a motor-running or drive-fault alarm with the mill in a stopped or fault state, often preceded by rising motor current, torque or vibration trend on the drive shaft and a drop in mill output or roll speed to zero; equipment-failure stop code is logged with maintenance intervention required to clear it.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Apply condition-based maintenance with periodic belt tension, alignment and wear inspection, vibration and thermal monitoring of the drive shaft, and scheduled replacement of belts, shafts and covers based on condition rather than failure; protect the belt cover from impact and keep it properly guarded.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Zeit zwischen Ereignissen: 1.685 Hr · laut Bericht: “Drive related failures”
    Wörtliches Zitat anzeigen
    Drive related failures 1685.17 6.83 - -
  2. Verlustzeit: 1,25 Hr · laut Bericht: “V1: Belt drive cover damaged”
    Wörtliches Zitat anzeigen
    02/22/16 015173 V1: Belt drive cover damaged CMP 0.75 0.5 1.25
  3. Mittlere Ereignisdauer: 6,83 Hr · laut Bericht: “Drive related failures”
    Wörtliches Zitat anzeigen
    Drive related failures 1685.17 6.83 - -
  4. Verlustzeit: 20,5 hours · laut Bericht: “belt failure, transmission shaft failure, minor belt cover damage”
    Wörtliches Zitat anzeigen
    The belt driven V1 has experienced belt failure, transmission shaft failure, and minor belt cover damage, resulting in a total stoppage of 20.5 hours.