Changeover disassembly, cleaning and reassembly of machine parts
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 57 % der Verlustzeit der Linie. Berichtet von 2 der 127 Studien, die sie beobachten konnten (begrenzte Evidenz).
Was passiert
At a product or format changeover the line must be stopped so that contact parts and tooling can be unbolted, taken off the machine, cleaned or sanitised to remove residual product and allergens, and then refitted and aligned before the next run can start. This manual, sequential work occupies the whole changeover window and keeps the line in a non-productive setup state until the first good unit is produced.
Was man dagegen tut
Apply SMED principles to convert internal tasks into external ones prepared in advance, standardise and pre-stage clean tooling sets, use quick-release fasteners and modular contact parts, and sequence or parallelise disassembly, cleaning and reassembly steps with trained changeover crews to shorten the non-productive window.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,7 % [0,2–1,8 %]
- Erwarteter Anteil an der Verlustzeit
- 0,4 % [0,1–1,0 %]
- Anteil an der Verlustzeit bei Auftreten
- 57 % [46–67 %]
- Studien / Einheiten
- 127 / 161
- Evidenzgrad
- C
Grad C: 2 bis 4 Studien oder eine Intervallbreite über 0,35.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,8 % [0,1–2,8 %]13 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte0,7 % [0,1–2,2 %]26 Studien
- Bier, Wein und Spirituosen0,8 % [0,1–2,7 %]11 Studien
- Backwaren und Teigwaren0,7 % [0,1–2,3 %]24 Studien
- Fleisch, Geflügel und Fisch0,8 % [0,1–2,6 %]9 Studien
- Obst- und Gemüseverarbeitung0,8 % [0,1–2,9 %]7 Studien
- Getreide- und Ölsaatenmüllerei0,8 % [0,1–2,9 %]6 Studien
- Zucker und Süßwaren0,8 % [0,1–2,8 %]9 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel1,2 % [0,2–4,1 %]5 Studien
- Futtermittel und Heimtiernahrung1,2 % [0,1–3,7 %]7 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)0,8 % [0,1–2,9 %]10 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseAt a product or format changeover the line must be stopped so that contact parts and tooling can be unbolted, taken off the machine, cleaned or sanitised to remove residual product and allergens, and then refitted and aligned before the next run can start. This manual, sequential work occupies the whole changeover window and keeps the line in a non-productive setup state until the first good unit is produced.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseMES/SCADA shows an extended machine-state period classified as changeover or setup, bounded by the last good unit of the previous order and the first good unit of the next, with no production counts advancing; operators log manual start/stop events for disassembly, cleaning and reassembly steps, and the duration correlates with format or recipe change events rather than with fault alarms.
Gegenmaßnahme
Ingenieurpraktische HinweiseApply SMED principles to convert internal tasks into external ones prepared in advance, standardise and pre-stage clean tooling sets, use quick-release fasteners and modular contact parts, and sequence or parallelise disassembly, cleaning and reassembly steps with trained changeover crews to shorten the non-productive window.
4Quellen
- Investigation on a multiscale sustainable manufacturing approach to production changeover complexity reduction and its implementation through smart surfaces and process optimization (2022)Quelle öffnenVerlustzeit: 660 min · laut Bericht: “Production machines dissembling, cleaning and assembling”
Wörtliches Zitat anzeigen
Production machines dissembling, cleaning and assembling 660 minutes
- Production Management Model Based on Lean Manufacturing Tools and SLP to Increase Productivity in a Meatball (BARF) Plant (2026)Quelle öffnenMittlere Ereignisdauer: 4,04 min · laut Bericht: “Disassemble parts of inactive equipment”
Wörtliches Zitat anzeigen
Disassemble parts of inactive equipment 4.04 Internal External
- Production Management Model Based on Lean Manufacturing Tools and SLP to Increase Productivity in a Meatball (BARF) Plant (2026)Quelle öffnenVerlustzeit: 4,04 min · laut Bericht: “Disassemble parts of inactive equipment”
Wörtliches Zitat anzeigen
Disassemble parts of inactive equipment 4.04

