Jam/blockage at coding or sealing station
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei weniger als 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 57 % der Verlustzeit der Linie. Berichtet von 0 der 120 Studien, die sie beobachten konnten (spärliche Evidenz).
Was passiert
Packaging material, product residue or a misaligned component becomes physically lodged in the coding head or the sealing jaws, preventing the mechanism from cycling and forcing the station into a blocked state. The obstruction is usually mechanical rather than a control fault, so the line stops until the blockage is manually cleared and the mechanism is reset.
Was man dagegen tut
Clear the physical obstruction, inspect and realign the coding head or sealing jaws, and verify material feed guides and tension settings. Implement a preventive maintenance routine to check wear parts and sensor cleanliness at these stations to reduce recurrence of blockages.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,4 % [0,1–1,1 %]
- Erwarteter Anteil an der Verlustzeit
- 0,2 % [0,0–0,6 %]
- Anteil an der Verlustzeit bei Auftreten
- 57 % [46–67 %]
- Studien / Einheiten
- 120 / 162
- Evidenzgrad
- D
Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,4 % [0,0–1,6 %]18 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte0,4 % [0,0–1,3 %]44 Studien
- Bier, Wein und Spirituosen0,4 % [0,0–1,5 %]16 Studien
- Backwaren und Teigwaren0,5 % [0,0–1,9 %]0 Studien
- Fleisch, Geflügel und Fisch0,5 % [0,0–1,9 %]6 Studien
- Obst- und Gemüseverarbeitung0,5 % [0,0–1,7 %]4 Studien
- Getreide- und Ölsaatenmüllerei0,5 % [0,0–1,8 %]6 Studien
- Zucker und Süßwaren0,5 % [0,0–1,8 %]3 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel0,5 % [0,0–1,7 %]6 Studien
- Futtermittel und Heimtiernahrung0,5 % [0,0–1,8 %]4 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)0,4 % [0,0–1,7 %]13 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweisePackaging material, product residue or a misaligned component becomes physically lodged in the coding head or the sealing jaws, preventing the mechanism from cycling and forcing the station into a blocked state. The obstruction is usually mechanical rather than a control fault, so the line stops until the blockage is manually cleared and the mechanism is reset.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseThe coding or sealing station reports a fault or blocked-state alarm, the machine status transitions to stopped with the specific station flagged, and cycle counters freeze while upstream stations continue running, causing blocking of upstream equipment and starvation downstream. Repeated short bursts of the same alarm code at that station are typical before a full stoppage.
Gegenmaßnahme
Ingenieurpraktische HinweiseClear the physical obstruction, inspect and realign the coding head or sealing jaws, and verify material feed guides and tension settings. Implement a preventive maintenance routine to check wear parts and sensor cleanliness at these stations to reduce recurrence of blockages.
4Quellen
- Integration of Overall Equipment Effectiveness and Six Sigma Approach to Minimize Product Defect and Machine Downtime (2023)Quelle öffnenAnzahl der Ereignisse: 1,00 events · laut Bericht: “Block Sealing”
Wörtliches Zitat anzeigen
Block Sealing 1
- Integration of Overall Equipment Effectiveness and Six Sigma Approach to Minimize Product Defect and Machine Downtime (2023)Quelle öffnenAnzahl der Ereignisse: 5,00 events · laut Bericht: “Block Coding”
Wörtliches Zitat anzeigen
Block Coding 5

