Component wear and tear
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei weniger als 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 58 % der Verlustzeit der Linie. Berichtet von 0 der 127 Studien, die sie beobachten konnten (spärliche Evidenz).
Was passiert
Mechanical parts such as bearings, seals, belts, chains and gaskets progressively lose material or elasticity through repeated friction, cyclic loading and contact with product or cleaning agents. Once the accumulated degradation passes a tolerance limit, the component can no longer perform its function and the equipment stops or fails.
Was man dagegen tut
Implement condition-based or time-based preventive maintenance with periodic inspection, lubrication and replacement of wear parts before they reach failure, supported by trending of condition-monitoring signals to anticipate degradation.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,4 % [0,1–1,1 %]
- Erwarteter Anteil an der Verlustzeit
- 0,2 % [0,0–0,6 %]
- Anteil an der Verlustzeit bei Auftreten
- 58 % [46–68 %]
- Studien / Einheiten
- 127 / 161
- Evidenzgrad
- D
Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,4 % [0,0–1,6 %]13 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte0,4 % [0,0–1,5 %]26 Studien
- Bier, Wein und Spirituosen0,4 % [0,0–1,6 %]11 Studien
- Backwaren und Teigwaren0,4 % [0,0–1,6 %]24 Studien
- Fleisch, Geflügel und Fisch0,4 % [0,0–1,7 %]9 Studien
- Obst- und Gemüseverarbeitung0,5 % [0,0–1,8 %]7 Studien
- Getreide- und Ölsaatenmüllerei0,5 % [0,0–1,8 %]6 Studien
- Zucker und Süßwaren0,4 % [0,0–1,8 %]9 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel0,4 % [0,0–1,7 %]5 Studien
- Futtermittel und Heimtiernahrung0,4 % [0,0–1,7 %]7 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)0,4 % [0,0–1,7 %]10 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseMechanical parts such as bearings, seals, belts, chains and gaskets progressively lose material or elasticity through repeated friction, cyclic loading and contact with product or cleaning agents. Once the accumulated degradation passes a tolerance limit, the component can no longer perform its function and the equipment stops or fails.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseSCADA/MES data show a gradual drift in vibration, current, torque or temperature trends on the affected asset before an unplanned stop, together with increasing frequency of short unplanned downtime alarms on the same machine over time. The stop event is typically logged as an unplanned mechanical or electrical fault with no preceding operator-triggered state change.
Gegenmaßnahme
Ingenieurpraktische HinweiseImplement condition-based or time-based preventive maintenance with periodic inspection, lubrication and replacement of wear parts before they reach failure, supported by trending of condition-monitoring signals to anticipate degradation.
4Quellen
- Penerapan Total Productive Maintenance (TPM) Pada Pabrik Gula Rafinasi di Indonesia (Studi Kasus: PT. XYZ) (2019)Quelle öffnenAnteil an den Verlustereignissen: 80,4 % · laut Bericht: “normal wear and tear”
Wörtliches Zitat anzeigen
Kerusakan mesin 80,44% terjadi karena adanya kerusakan komponen yang masuk kategori normal wear and tear atau aus karena umur pakainya.

