Equipment configuration/setup time
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 56 % der Verlustzeit der Linie. Berichtet von 0 der 29 Studien, die sie beobachten konnten (spärliche Evidenz).
Was passiert
Before a new batch or product run can start, the incubation equipment must be reconfigured with new recipe parameters such as temperature set points, time cycles and control sequences, and this parameterisation work occupies time between the end of the previous run and the start of stable production. The loss is organisational and procedural rather than a mechanical failure, arising from the need to re-enter or reload settings and verify them before the process is allowed to proceed.
Was man dagegen tut
Standardise and pre-validate recipes so operators select a stored parameter set instead of manually entering values, and use automated recipe management to download settings directly to the controller. Apply quick-changeover principles to separate internal from external setup tasks and shift as much preparation as possible to before the line stops.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,5 % [0,1–1,7 %]
- Erwarteter Anteil an der Verlustzeit
- 0,3 % [0,0–1,0 %]
- Anteil an der Verlustzeit bei Auftreten
- 56 % [43–67 %]
- Studien / Einheiten
- 29 / 33
- Evidenzgrad
- D
Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,6 % [0,0–2,4 %]8 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte0,6 % [0,1–2,6 %]1 Studie
- Bier, Wein und Spirituosen0,6 % [0,0–2,7 %]0 Studien
- Backwaren und Teigwaren0,6 % [0,0–2,5 %]1 Studie
- Fleisch, Geflügel und Fisch0,6 % [0,1–2,6 %]0 Studien
- Obst- und Gemüseverarbeitung0,6 % [0,1–2,6 %]2 Studien
- Getreide- und Ölsaatenmüllerei0,6 % [0,0–2,8 %]0 Studien
- Zucker und Süßwaren0,6 % [0,1–2,5 %]3 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel0,6 % [0,0–2,5 %]3 Studien
- Futtermittel und Heimtiernahrung0,6 % [0,0–2,6 %]4 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)0,6 % [0,0–2,7 %]7 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseBefore a new batch or product run can start, the incubation equipment must be reconfigured with new recipe parameters such as temperature set points, time cycles and control sequences, and this parameterisation work occupies time between the end of the previous run and the start of stable production. The loss is organisational and procedural rather than a mechanical failure, arising from the need to re-enter or reload settings and verify them before the process is allowed to proceed.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseThe SCADA/MES log shows the equipment in a changeover or setup machine state with no production counts, often preceded by a recipe selection or parameter download event and followed by a ramp to target conditions before the first good unit is recorded. There are typically no fault alarms associated with the interval, only state-duration entries tagged as configuration or changeover.
Gegenmaßnahme
Ingenieurpraktische HinweiseStandardise and pre-validate recipes so operators select a stored parameter set instead of manually entering values, and use automated recipe management to download settings directly to the controller. Apply quick-changeover principles to separate internal from external setup tasks and shift as much preparation as possible to before the line stops.
4Quellen
- Verlustzeit: 28,2 min · laut Bericht: “configuration time”
Wörtliches Zitat anzeigen
The use of efficient tools allowed to reduce the configuration time to only 28.20 minutes.

