Container Body or Seal Defect
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 49 % der Verlustzeit der Linie. Berichtet von 1 der 120 Studien, die sie beobachten konnten (spärliche Evidenz).
Was passiert
Filled containers are rejected because the container body shows deformation, cracks, flash or dimensional faults, or because the closure/seal is incomplete, misaligned or leaking. These faults usually originate upstream in container moulding, handling or the capping/sealing head rather than in the filler itself, but they are only detected and counted once the unit reaches the filling or inspection stage.
Was man dagegen tut
Reinforce incoming container quality checks and supplier specifications, and calibrate or adjust the sealing/capping head pressure, temperature and alignment. Periodic preventive inspection of mould and seal-forming tooling reduces recurrence of body and seal faults.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,6 % [0,1–1,5 %]
- Erwarteter Anteil an der Verlustzeit
- 0,3 % [0,1–0,7 %]
- Anteil an der Verlustzeit bei Auftreten
- 49 % [38–61 %]
- Studien / Einheiten
- 120 / 162
- Evidenzgrad
- D
Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,6 % [0,1–2,1 %]18 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte0,5 % [0,1–1,7 %]44 Studien
- Bier, Wein und Spirituosen0,6 % [0,1–2,2 %]16 Studien
- Backwaren und Teigwaren0,7 % [0,1–2,6 %]0 Studien
- Fleisch, Geflügel und Fisch0,6 % [0,1–2,4 %]6 Studien
- Obst- und Gemüseverarbeitung0,7 % [0,1–2,6 %]4 Studien
- Getreide- und Ölsaatenmüllerei1,0 % [0,1–3,6 %]6 Studien
- Zucker und Süßwaren0,7 % [0,1–2,4 %]3 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel0,6 % [0,1–2,5 %]6 Studien
- Futtermittel und Heimtiernahrung0,7 % [0,1–2,5 %]4 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)0,6 % [0,1–2,3 %]13 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseFilled containers are rejected because the container body shows deformation, cracks, flash or dimensional faults, or because the closure/seal is incomplete, misaligned or leaking. These faults usually originate upstream in container moulding, handling or the capping/sealing head rather than in the filler itself, but they are only detected and counted once the unit reaches the filling or inspection stage.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseMES/quality logs show an increase in reject counts tagged with body-defect or seal-defect codes at the filling or downstream inspection station, while the filler machine state remains in run with no fault alarm. No equipment stoppage is typically associated; the signature is a rise in the defect-rate counter rather than a downtime event.
Gegenmaßnahme
Ingenieurpraktische HinweiseReinforce incoming container quality checks and supplier specifications, and calibrate or adjust the sealing/capping head pressure, temperature and alignment. Periodic preventive inspection of mould and seal-forming tooling reduces recurrence of body and seal faults.
4Quellen
- Integration of Overall Equipment Effectiveness and Six Sigma Approach to Minimize Product Defect and Machine Downtime (2023)Quelle öffnenAnteil an den Verlustereignissen: 22,0 % · laut Bericht: “Body Defect”
Wörtliches Zitat anzeigen
Body Defect 1012 22
- Integration of Overall Equipment Effectiveness and Six Sigma Approach to Minimize Product Defect and Machine Downtime (2023)Quelle öffnenAnzahl der Ereignisse: 1.012 units · laut Bericht: “Body Defect”
Wörtliches Zitat anzeigen
Body Defect 1012 22
- Integration of Overall Equipment Effectiveness and Six Sigma Approach to Minimize Product Defect and Machine Downtime (2023)Quelle öffnenAnteil an den Verlustereignissen: 56,0 % · laut Bericht: “Seal Defect”
Wörtliches Zitat anzeigen
Seal Defect 2555 56
- Integration of Overall Equipment Effectiveness and Six Sigma Approach to Minimize Product Defect and Machine Downtime (2023)Quelle öffnenAnzahl der Ereignisse: 2.555 units · laut Bericht: “Seal Defect”
Wörtliches Zitat anzeigen
Seal Defect 2555 56
- Proposal for improvement to increase the overall equipment effectiveness (OEE) of a dairy products company through a Preventive Maintenance Plan, Standardized Work, and SMED (2025)Quelle öffnenAnteil an der geplanten Zeit: 0,0500 % · laut Bericht: “Defectuosos”
Wörtliches Zitat anzeigen
Charlas /Reuniones Velocidad reducida Defectuosos 1,50% 2,10% 0,05%
- Proposal for improvement to increase the overall equipment effectiveness (OEE) of a dairy products company through a Preventive Maintenance Plan, Standardized Work, and SMED (2025)Quelle öffnenAnteil an der geplanten Zeit: 0,0500 % · laut Bericht: “Defectuosos”
Wörtliches Zitat anzeigen
Charlas /Reuniones Velocidad reducida Defectuosos 1,50% 1,00% 0,05%

