foratvise
Loslegen
Anlagenausfall (Störungen)

Conveyor drive motor burnout or mechanical failure

Anlagenausfall (Störungen)VerfügbarkeitFördern und Puffern

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei etwa 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 58 % der Verlustzeit der Linie. Berichtet von 1 der 86 Studien, die sie beobachten konnten (spärliche Evidenz).

Was passiert

The conveyor drive motor overheats and burns its windings, or suffers mechanical failure of bearings, shaft or gearbox, usually due to sustained overload, jammed belt, lack of lubrication or electrical insulation degradation. Loss of torque or motor function stops the conveyor and interrupts material flow along the line.

Was man dagegen tut

Apply condition-based maintenance with vibration and thermal monitoring of the drive motor, verify correct motor sizing and overload protection settings, and keep lubrication and alignment within specification. Clear belt jams promptly and install mechanical or electronic overload protection that trips before windings overheat.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
0,7 % [0,1–1,8 %]
Erwarteter Anteil an der Verlustzeit
0,4 % [0,1–1,1 %]
Anteil an der Verlustzeit bei Auftreten
58 % [47–68 %]
Studien / Einheiten
86 / 112
Evidenzgrad
D

Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    0,7 % [0,1–2,7 %]11 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    0,9 % [0,1–3,0 %]28 Studien
  • Bier, Wein und Spirituosen
    0,7 % [0,1–2,8 %]12 Studien
  • Backwaren und Teigwaren
    0,8 % [0,1–3,1 %]0 Studien
  • Fleisch, Geflügel und Fisch
    0,8 % [0,1–2,9 %]5 Studien
  • Obst- und Gemüseverarbeitung
    0,8 % [0,1–2,8 %]4 Studien
  • Getreide- und Ölsaatenmüllerei
    0,8 % [0,1–3,0 %]4 Studien
  • Zucker und Süßwaren
    0,8 % [0,1–2,9 %]4 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    0,8 % [0,1–2,7 %]4 Studien
  • Futtermittel und Heimtiernahrung
    0,8 % [0,1–3,0 %]5 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    0,7 % [0,1–2,7 %]9 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

The conveyor drive motor overheats and burns its windings, or suffers mechanical failure of bearings, shaft or gearbox, usually due to sustained overload, jammed belt, lack of lubrication or electrical insulation degradation. Loss of torque or motor function stops the conveyor and interrupts material flow along the line.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

Motor current or torque rises progressively before tripping on overcurrent or thermal overload alarm, followed by a prolonged conveyor stopped state requiring maintenance reset rather than operator clearance. Upstream equipment shows blocking and downstream equipment shows starvation during the stop, and the event log records an electrical or mechanical fault code tied to the drive motor.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Apply condition-based maintenance with vibration and thermal monitoring of the drive motor, verify correct motor sizing and overload protection settings, and keep lubrication and alignment within specification. Clear belt jams promptly and install mechanical or electronic overload protection that trips before windings overheat.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Anteil an den Verlustereignissen: 81,0 % · laut Bericht: “Queima do motor / falhas mecânicas”
    Wörtliches Zitat anzeigen
    O tempo de linha parada pela queima do motor, ou falhas mecânicas representava 81% das ocorrências, de acordo com os registros históricos da área de manutenção, sendo assim esta causa foi validada.