foratvise
Loslegen
Anlagenausfall (Störungen)

Feed system failure

Anlagenausfall (Störungen)VerfügbarkeitMahlen und Zerkleinern

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei etwa 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 57 % der Verlustzeit der Linie. Berichtet von 0 der 43 Studien, die sie beobachten konnten (spärliche Evidenz).

Was passiert

The mechanism that feeds raw material into the mill (screw conveyor, hopper feeder, rotary valve or metering device) loses its function due to mechanical wear, jamming of the drive, blockage by product build-up, or failure of its motor or coupling, so material stops reaching the grinding unit at the required rate. This forces the mill to stop or run empty until the feeding equipment is repaired or cleared by maintenance.

Was man dagegen tut

Apply preventive maintenance to the feeder drive, bearings and couplings, install sensors to detect blockage or no-flow conditions early, and design hoppers and chutes to minimize bridging or compaction of the material. Keep critical feeder spare parts available and train operators to clear minor obstructions without waiting for a full maintenance intervention.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
0,6 % [0,1–1,8 %]
Erwarteter Anteil an der Verlustzeit
0,3 % [0,0–1,1 %]
Anteil an der Verlustzeit bei Auftreten
57 % [46–68 %]
Studien / Einheiten
43 / 48
Evidenzgrad
D

Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    0,7 % [0,1–2,9 %]5 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    0,7 % [0,1–3,0 %]1 Studie
  • Bier, Wein und Spirituosen
    0,7 % [0,1–2,9 %]0 Studien
  • Backwaren und Teigwaren
    0,7 % [0,1–2,9 %]0 Studien
  • Fleisch, Geflügel und Fisch
    0,7 % [0,1–2,8 %]0 Studien
  • Obst- und Gemüseverarbeitung
    0,7 % [0,1–2,9 %]2 Studien
  • Getreide- und Ölsaatenmüllerei
    0,7 % [0,1–2,8 %]7 Studien
  • Zucker und Süßwaren
    0,6 % [0,1–2,6 %]10 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    0,7 % [0,1–2,9 %]5 Studien
  • Futtermittel und Heimtiernahrung
    0,7 % [0,1–2,7 %]6 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    0,7 % [0,1–2,7 %]7 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

The mechanism that feeds raw material into the mill (screw conveyor, hopper feeder, rotary valve or metering device) loses its function due to mechanical wear, jamming of the drive, blockage by product build-up, or failure of its motor or coupling, so material stops reaching the grinding unit at the required rate. This forces the mill to stop or run empty until the feeding equipment is repaired or cleared by maintenance.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

SCADA/MES shows the feeder motor current or speed signal dropping to zero or to an abnormal value while the mill drive continues running, often accompanied by a low-level or no-flow alarm on the feed hopper and an unplanned downtime state logged against the feeding equipment. Repeated short-to-long stop events on the feeder, combined with starvation of the mill downstream, are typical of this failure mode.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Apply preventive maintenance to the feeder drive, bearings and couplings, install sensors to detect blockage or no-flow conditions early, and design hoppers and chutes to minimize bridging or compaction of the material. Keep critical feeder spare parts available and train operators to clear minor obstructions without waiting for a full maintenance intervention.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Anzahl der Ereignisse: 36,0 events · laut Bericht: “System feeding”
    Wörtliches Zitat anzeigen
    Alimentação do sistema 36 146,1 221,5 49060,6 55,5
  2. Mittlere Ereignisdauer: 146 min · laut Bericht: “System feeding”
    Wörtliches Zitat anzeigen
    Alimentação do sistema 36 146,1 221,5 49060,6 55,5