foratvise
Loslegen
Rüsten und Einstellen

Mixed and undifferentiated filler losses (changeover, breakdown, stoppage, defects)

Rüsten und EinstellenVerfügbarkeitAbfüllen

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei weniger als 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 57 % der Verlustzeit der Linie. Berichtet von 1 der 120 Studien, die sie beobachten konnten (spärliche Evidenz).

Was passiert

Losses attributed to the filler combine several distinct underlying origins reported together in the source data: product or format changeovers with their adjustment time, unplanned mechanical or electrical breakdowns requiring corrective maintenance, generic line stoppages whose cause is not specified, and defective units detected at the filling station. Because the primary study logs all of these under a single equipment or report heading, the physical mechanism varies event by event rather than following one consistent failure mode.

Was man dagegen tut

Standardize changeover procedures separately from corrective-maintenance work orders, and improve stop-code granularity in the SCADA/MES configuration so that setup, breakdown, line-stop and defect events on the filler are logged under distinct, consistently applied categories. This reclassification enables proper root-cause analysis and allows each loss type to be targeted with its own dedicated improvement action rather than a single generic fix.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
0,5 % [0,1–1,4 %]
Erwarteter Anteil an der Verlustzeit
0,3 % [0,1–0,8 %]
Anteil an der Verlustzeit bei Auftreten
57 % [45–67 %]
Studien / Einheiten
120 / 162
Evidenzgrad
D

Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    0,5 % [0,1–2,0 %]18 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    0,6 % [0,1–2,1 %]44 Studien
  • Bier, Wein und Spirituosen
    0,5 % [0,1–2,0 %]16 Studien
  • Backwaren und Teigwaren
    0,6 % [0,1–2,3 %]0 Studien
  • Fleisch, Geflügel und Fisch
    0,6 % [0,1–2,2 %]6 Studien
  • Obst- und Gemüseverarbeitung
    0,6 % [0,1–2,3 %]4 Studien
  • Getreide- und Ölsaatenmüllerei
    0,6 % [0,1–2,1 %]6 Studien
  • Zucker und Süßwaren
    0,6 % [0,1–2,2 %]3 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    0,6 % [0,1–2,2 %]6 Studien
  • Futtermittel und Heimtiernahrung
    0,6 % [0,1–2,3 %]4 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    0,6 % [0,1–2,2 %]13 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

Losses attributed to the filler combine several distinct underlying origins reported together in the source data: product or format changeovers with their adjustment time, unplanned mechanical or electrical breakdowns requiring corrective maintenance, generic line stoppages whose cause is not specified, and defective units detected at the filling station. Because the primary study logs all of these under a single equipment or report heading, the physical mechanism varies event by event rather than following one consistent failure mode.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

In SCADA/MES the filler tag shows alternating machine states such as changeover, fault/alarm and running, each with its own downtime counter, together with a reject or defect counter tied to the filling station; however the stop codes and state transitions are not consistently mapped to a single root cause, so the historian shows a heterogeneous mix of short and long stops and quality rejects under the same equipment identifier. This inconsistency itself is diagnostic of a cluster where classification granularity is insufficient at the source.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Standardize changeover procedures separately from corrective-maintenance work orders, and improve stop-code granularity in the SCADA/MES configuration so that setup, breakdown, line-stop and defect events on the filler are logged under distinct, consistently applied categories. This reclassification enables proper root-cause analysis and allows each loss type to be targeted with its own dedicated improvement action rather than a single generic fix.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Fehlerquote: 0,200 % · laut Bericht: “Taxa de Defeitos em Serviços (SDR)”
    Wörtliches Zitat anzeigen
    Verificou-se que de janeiro a outubro de 2005 o indicador Taxa de Defeitos em Serviços (SDR) da empresa Gama S.A. teve a enchedora de partes sólidas Klockner colaborando em média 0,2 % e um pico de 1,02% conforme Figura 44.
  2. Verlustzeit: 22,0 h · laut Bericht: “Paradas de linha”
    Wörtliches Zitat anzeigen
    Nesta análise de definição do problema verificou-se também que de janeiro a outubro de 2005 esta sala de produção teve em média 22 horas de paradas de linha conforme mostrado na Figura 46.
  3. Verlustzeit: 162 min · laut Bericht: “Setup (segunda-feira)”
    Wörtliches Zitat anzeigen
    A Figura 60 mostra o valor do setup atual da klockner após os vários exercícios de SMED, onde ele foi reduzido em 70% nas segundas-feiras , saindo dos valores de 162 minutos para apenas 47 minutos.
  4. Verlustzeit: 3,70 h · laut Bericht: “Quebras da máquina (manutenção corretiva)”
    Wörtliches Zitat anzeigen
    Para o indicador de Quebras na máquina Klockner, conforme a Figura 69, podemos ver que os tempos gasto em manutenção devido a quebra do equipamento foi reduzida de 6,9h para 3,7 horas o que representou uma melhora de 46% neste equipamento
  5. Verlustzeit: 10,0 h · laut Bericht: “Paradas de linha e setups”
    Wörtliches Zitat anzeigen
    O indicador de paradas de linhas e setups da Klocner, conforme a Figura 70, teve uma redução de 23h de paradas e set ups para um tempo de 10 horas o que representou uma melhora de 57%.
  6. Verlustzeit: 47,0 min · laut Bericht: “Setup (segunda-feira)”
    Wörtliches Zitat anzeigen
    A Figura 60 mostra o valor do setup atual da klockner após os vários exercícios de SMED, onde ele foi reduzido em 70% nas segundas-feiras , saindo dos valores de 162 minutos para apenas 47 minutos.
  7. Anteil an der Verlustzeit: 70,0 % · laut Bericht: “Máquina enchedora (problemas no equipamento Klockner)”
    Wörtliches Zitat anzeigen
    observou-se, Figura 50, que 70% das paradas de linha estavam relacionadas a problemas no equipamento da Klockner, 16% por problemas de fornecimento de energia e 9% por problemas na máquina de injetora de tinta que faz as identificações nas bolsas plásticas.