foratvise
Loslegen
Anlaufverluste (verminderte Ausbeute)

Filler start-up yield loss

Anlaufverluste (verminderte Ausbeute)QualitätAbfüllen

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei weniger als 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 47 % der Verlustzeit der Linie. Berichtet von 0 der 120 Studien, die sie beobachten konnten (spärliche Evidenz).

Was passiert

During the ramp-up of the filling machine after a stop, changeover or line start, fill valves, dosing pumps and level/weight controls have not yet stabilised, so containers are under-filled, over-filled or run empty before the setpoint is reached. Product used to prime lines, displace air or flush the product-water interface is diverted to drain or scrap rather than into saleable packs.

Was man dagegen tut

Standardise and automate the start-up sequence with recipe-driven ramp profiles for valves and pumps, use in-line sensors to detect when fill parameters are within tolerance before accepting packs as good, and minimise product lost to priming or interface flushing through recirculation or smaller dedicated flush volumes.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
0,3 % [0,0–1,0 %]
Erwarteter Anteil an der Verlustzeit
0,1 % [0,0–0,5 %]
Anteil an der Verlustzeit bei Auftreten
47 % [28–65 %]
Studien / Einheiten
120 / 162
Evidenzgrad
D

Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    0,4 % [0,0–1,4 %]18 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    0,3 % [0,0–1,1 %]44 Studien
  • Bier, Wein und Spirituosen
    0,4 % [0,0–1,4 %]16 Studien
  • Backwaren und Teigwaren
    0,4 % [0,0–1,6 %]0 Studien
  • Fleisch, Geflügel und Fisch
    0,4 % [0,0–1,5 %]6 Studien
  • Obst- und Gemüseverarbeitung
    0,4 % [0,0–1,5 %]4 Studien
  • Getreide- und Ölsaatenmüllerei
    0,4 % [0,0–1,5 %]6 Studien
  • Zucker und Süßwaren
    0,4 % [0,0–1,6 %]3 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    0,4 % [0,0–1,5 %]6 Studien
  • Futtermittel und Heimtiernahrung
    0,4 % [0,0–1,5 %]4 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    0,4 % [0,0–1,5 %]13 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

During the ramp-up of the filling machine after a stop, changeover or line start, fill valves, dosing pumps and level/weight controls have not yet stabilised, so containers are under-filled, over-filled or run empty before the setpoint is reached. Product used to prime lines, displace air or flush the product-water interface is diverted to drain or scrap rather than into saleable packs.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

SCADA shows the filler in a start-up or warm-up machine state preceding the stable-run state, with fill weight/level or flow signals outside control limits during the first cycles, elevated reject or recirculation counts coincident with this state, and a gap between total product metered and good packs produced immediately after each restart.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Standardise and automate the start-up sequence with recipe-driven ramp profiles for valves and pumps, use in-line sensors to detect when fill parameters are within tolerance before accepting packs as good, and minimise product lost to priming or interface flushing through recirculation or smaller dedicated flush volumes.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Verlustzeit: 99,0 min · laut Bericht: “Reduced Yield”
    Wörtliches Zitat anzeigen
    Reduced Yield 99 1,4 100
  2. Anteil an der Verlustzeit: 1,40 % · laut Bericht: “Reduced Yield”
    Wörtliches Zitat anzeigen
    Reduced Yield 99 1,4 100