Gripper Failure
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei weniger als 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 57 % der Verlustzeit der Linie. Berichtet von 0 der 120 Studien, die sie beobachten konnten (spärliche Evidenz).
Was passiert
The mechanical gripper that picks up, transfers or positions containers at the filling station loses its ability to clamp or release correctly because of worn jaws or pads, fatigued springs, misaligned actuators, pneumatic leakage or accumulated debris. When the gripper fails to seize, center or let go of a container it causes a dropped, crooked or jammed unit that forces the station to stop until the mechanism is cleared or repaired.
Was man dagegen tut
Apply preventive maintenance on gripper jaws, pads and springs with scheduled replacement based on wear, inspect and recalibrate pneumatic cylinders or servo actuators, and keep the mechanism clean and lubricated. Verify grip-force and position sensors regularly and adjust guide rails or centering guides that feed containers into the gripper.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,4 % [0,1–1,2 %]
- Erwarteter Anteil an der Verlustzeit
- 0,2 % [0,0–0,7 %]
- Anteil an der Verlustzeit bei Auftreten
- 57 % [46–67 %]
- Studien / Einheiten
- 120 / 162
- Evidenzgrad
- D
Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,4 % [0,0–1,7 %]18 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte0,4 % [0,0–1,3 %]44 Studien
- Bier, Wein und Spirituosen0,4 % [0,0–1,6 %]16 Studien
- Backwaren und Teigwaren0,5 % [0,0–1,9 %]0 Studien
- Fleisch, Geflügel und Fisch0,5 % [0,0–1,8 %]6 Studien
- Obst- und Gemüseverarbeitung0,5 % [0,0–1,8 %]4 Studien
- Getreide- und Ölsaatenmüllerei0,5 % [0,0–1,7 %]6 Studien
- Zucker und Süßwaren0,5 % [0,0–1,9 %]3 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel0,5 % [0,0–1,7 %]6 Studien
- Futtermittel und Heimtiernahrung0,5 % [0,0–1,9 %]4 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)0,4 % [0,0–1,8 %]13 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseThe mechanical gripper that picks up, transfers or positions containers at the filling station loses its ability to clamp or release correctly because of worn jaws or pads, fatigued springs, misaligned actuators, pneumatic leakage or accumulated debris. When the gripper fails to seize, center or let go of a container it causes a dropped, crooked or jammed unit that forces the station to stop until the mechanism is cleared or repaired.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseSCADA/MES logs show fault or alarm codes tied specifically to the gripper or pick-and-place axis (position error, grip-force or proximity sensor fault), with the filler transitioning to a fault state while upstream conveyors fill up and downstream stations starve. The event recurs as isolated stops localized to the same station address rather than spreading uniformly across the line.
Gegenmaßnahme
Ingenieurpraktische HinweiseApply preventive maintenance on gripper jaws, pads and springs with scheduled replacement based on wear, inspect and recalibrate pneumatic cylinders or servo actuators, and keep the mechanism clean and lubricated. Verify grip-force and position sensors regularly and adjust guide rails or centering guides that feed containers into the gripper.
4Quellen
- Integration of Overall Equipment Effectiveness and Six Sigma Approach to Minimize Product Defect and Machine Downtime (2023)Quelle öffnenAnzahl der Ereignisse: 12,0 events · laut Bericht: “Gripper”
Wörtliches Zitat anzeigen
Gripper 12

