Mill center shaft drive failure
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 59 % der Verlustzeit der Linie. Berichtet von 2 der 43 Studien, die sie beobachten konnten (spärliche Evidenz).
Was passiert
The drive train of the mill center shaft (transmission belts, pulleys, sleeves and the shaft itself) degrades through continuous mechanical wear, fatigue and misalignment until a component slips, breaks or seizes. Belts turning over, pulley ends snapping or sleeves wearing out progressively reduce torque transmission until the shaft can no longer drive the mill, forcing an unplanned stop.
Was man dagegen tut
Establish a condition-based maintenance program for the shaft drive train, including periodic inspection and timely replacement of belts, pulleys and sleeves before wear-out, shaft alignment checks, and vibration or current monitoring to detect incipient degradation. Keep critical spares on hand to shorten repair time when failures do occur.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 1,0 % [0,2–2,9 %]
- Erwarteter Anteil an der Verlustzeit
- 0,6 % [0,1–1,7 %]
- Anteil an der Verlustzeit bei Auftreten
- 59 % [49–69 %]
- Studien / Einheiten
- 43 / 48
- Evidenzgrad
- D
Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.
2Wahrscheinlichkeit nach Segment
- Milchprodukte1,1 % [0,1–4,4 %]5 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte1,2 % [0,1–4,4 %]1 Studie
- Bier, Wein und Spirituosen1,2 % [0,1–4,6 %]0 Studien
- Backwaren und Teigwaren1,2 % [0,1–4,7 %]0 Studien
- Fleisch, Geflügel und Fisch1,2 % [0,1–5,0 %]0 Studien
- Obst- und Gemüseverarbeitung1,2 % [0,1–4,6 %]2 Studien
- Getreide- und Ölsaatenmüllerei1,1 % [0,1–4,2 %]7 Studien
- Zucker und Süßwaren1,1 % [0,1–3,9 %]10 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel1,7 % [0,2–6,3 %]5 Studien
- Futtermittel und Heimtiernahrung1,1 % [0,1–4,1 %]6 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)1,1 % [0,1–4,3 %]7 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseThe drive train of the mill center shaft (transmission belts, pulleys, sleeves and the shaft itself) degrades through continuous mechanical wear, fatigue and misalignment until a component slips, breaks or seizes. Belts turning over, pulley ends snapping or sleeves wearing out progressively reduce torque transmission until the shaft can no longer drive the mill, forcing an unplanned stop.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseSCADA/MES shows unplanned stop events logged against the center or transmission shaft asset with equipment_failure codes and durations long enough to require maintenance intervention, often preceded by rising motor current, torque or vibration trends on the drive. Repeated short-interval failures on the same shaft/pulley/belt tag and downstream starvation of the mill outfeed are typical patterns.
Gegenmaßnahme
Ingenieurpraktische HinweiseEstablish a condition-based maintenance program for the shaft drive train, including periodic inspection and timely replacement of belts, pulleys and sleeves before wear-out, shaft alignment checks, and vibration or current monitoring to detect incipient degradation. Keep critical spares on hand to shorten repair time when failures do occur.
4Quellen
- Reliability Measurement of Torque Transmission System for Spice Manufacturing Plant (2019)Quelle öffnenZeit zwischen Ereignissen: 2.734 Hr · laut Bericht: “Mill centre shaft failure/Service”
Wörtliches Zitat anzeigen
Mill centre shaft failure/Service - - 2734.38 73.63
- Reliability Measurement of Torque Transmission System for Spice Manufacturing Plant (2019)Quelle öffnenVerlustzeit: 18,0 Hr · laut Bericht: “V1: Transmission shaft (TS1) bottom pulley end broken”
Wörtliches Zitat anzeigen
01/16/17 017640 V1: Transmission shaft (TS1) bottom pulley end broken CMU 16 2 18
- Reliability Measurement of Torque Transmission System for Spice Manufacturing Plant (2019)Quelle öffnenVerlustzeit: 1,25 Hr · laut Bericht: “V1: Center shaft - transmission shaft belt change”
Wörtliches Zitat anzeigen
12/19/16 017414 V1: Center shaft - transmission shaft belt change CMP 0 1.25 1.25
- Reliability Measurement of Torque Transmission System for Spice Manufacturing Plant (2019)Quelle öffnenVerlustzeit: 1,50 Hr · laut Bericht: “V1: Center shaft pulley belts turned over”
Wörtliches Zitat anzeigen
12/29/16 017518 V1: Center shaft pulley belts turned over CMU 0 1.5 1.5
- Reliability Measurement of Torque Transmission System for Spice Manufacturing Plant (2019)Quelle öffnenVerlustzeit: 125 Hr · laut Bericht: “V4: Center shaft service (Sleeve worn out)”
Wörtliches Zitat anzeigen
12/24/15 014674 V4: Center shaft service (Sleeve worn out) CMU 112 13.25 125.25
- Reliability Measurement of Torque Transmission System for Spice Manufacturing Plant (2019)Quelle öffnenMittlere Ereignisdauer: 73,6 Hr · laut Bericht: “Mill centre shaft failure/Service”
Wörtliches Zitat anzeigen
Mill centre shaft failure/Service - - 2734.38 73.63

