Minor stoppage of milling equipment
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 2 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 54 % der Verlustzeit der Linie. Berichtet von 3 der 43 Studien, die sie beobachten konnten (begrenzte Evidenz).
Was passiert
Grinding and polishing machines experience brief interruptions in material flow, caused by small jams, blockages of feed or discharge paths, sensor misreads or momentary mechanical hang-ups in the milling chain. These stoppages are cleared quickly by the operator without needing maintenance intervention, but they repeatedly interrupt the continuous feeding and discharge of grain or kernels through the mill.
Was man dagegen tut
Improve feed and discharge path design to reduce jamming points, install sensors and guards that prevent small obstructions from stopping the line, and train operators in rapid clearing procedures. Regular preventive inspection of feed chutes, screens and rollers reduces the frequency of these interruptions.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 1,8 % [0,4–4,8 %]
- Erwarteter Anteil an der Verlustzeit
- 1,0 % [0,2–2,7 %]
- Anteil an der Verlustzeit bei Auftreten
- 54 % [41–65 %]
- Studien / Einheiten
- 43 / 48
- Evidenzgrad
- C
Grad C: 2 bis 4 Studien oder eine Intervallbreite über 0,35.
2Wahrscheinlichkeit nach Segment
- Milchprodukte2,0 % [0,2–7,3 %]5 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte2,1 % [0,2–8,1 %]1 Studie
- Bier, Wein und Spirituosen2,2 % [0,2–7,9 %]0 Studien
- Backwaren und Teigwaren2,1 % [0,2–7,5 %]0 Studien
- Fleisch, Geflügel und Fisch2,1 % [0,3–7,8 %]0 Studien
- Obst- und Gemüseverarbeitung2,1 % [0,2–7,8 %]2 Studien
- Getreide- und Ölsaatenmüllerei2,8 % [0,4–8,9 %]7 Studien
- Zucker und Süßwaren3,6 % [0,6–11,6 %]10 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel1,9 % [0,2–6,2 %]5 Studien
- Futtermittel und Heimtiernahrung2,0 % [0,2–6,9 %]6 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)1,9 % [0,2–6,7 %]7 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseGrinding and polishing machines experience brief interruptions in material flow, caused by small jams, blockages of feed or discharge paths, sensor misreads or momentary mechanical hang-ups in the milling chain. These stoppages are cleared quickly by the operator without needing maintenance intervention, but they repeatedly interrupt the continuous feeding and discharge of grain or kernels through the mill.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseSCADA/MES logs show frequent short machine-state transitions to stopped or idle on the grinding or polishing station, each lasting only a few minutes, interspersed with brief operator-reset events and no associated maintenance work order. Feed rate or motor load signals typically drop momentarily and recover without a corresponding fault code, and the frequency of these micro-stops accumulates into a distinct idling counter separate from breakdown stops.
Gegenmaßnahme
Ingenieurpraktische HinweiseImprove feed and discharge path design to reduce jamming points, install sensors and guards that prevent small obstructions from stopping the line, and train operators in rapid clearing procedures. Regular preventive inspection of feed chutes, screens and rollers reduces the frequency of these interruptions.
4Quellen
- Anteil an der Verlustzeit: 12,1 % · laut Bericht: “idle and minor stoppages”
Wörtliches Zitat anzeigen
Rata-rata kerugian yang terjadi pada setiap mesin yaitu breakdown losses 0,048%, setup and adjustment losses 0,159%, idle and minor stoppages 12,127%, dan reduced speed losses 11,749%.
- Peningkatan overall equipment effectiveness (OEE) mesin grinding pada produksi cokelat bubuk di PT ABC (2023)Quelle öffnenAnteil an der geplanten Zeit: 10,0 % · laut Bericht: “idling and minor stoppages”
Wörtliches Zitat anzeigen
Rata-rata yang diperoleh dari persentase idling and minor stoppages losses yaitu seebesar 10 %.
- ANALISIS EFEKTIVITAS MESIN POLES BERAS (RICE POLISHER) MENGGUNAKAN METODE OVERALL EQUIPMENT EFFECTIVENESS (OEE) DAN SIX BIG LOSSES PADA PB TRI HANIFA BERBASIS KONSEP TOTAL PRODUCTIVE MAINTENANCE (TPM) (2026)Quelle öffnenAnteil an der Verlustzeit: 10,5 % · laut Bericht: “idling and minor stoppages”
Wörtliches Zitat anzeigen
Kerugian terbesar berasal dari reduced speed losses sebesar 51,09% dan idling and minor stoppages sebesar 10,53%.

