foratvise
Loslegen
Anlagenausfall (Störungen)

Pneumatic Component Failure (Air Hose / Solenoid Valve)

Anlagenausfall (Störungen)VerfügbarkeitAbfüllen

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei weniger als 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 57 % der Verlustzeit der Linie. Berichtet von 0 der 120 Studien, die sie beobachten konnten (spärliche Evidenz).

Was passiert

The pneumatic circuit that actuates the filling valves, cylinders or nozzles loses integrity because an air hose cracks, splits, abrades or disconnects from vibration and fatigue, or because a solenoid valve sticks, wears internally, or suffers a coil/electrical fault that blocks air flow. Without reliable compressed air delivery or switching, the filling actuators cannot move correctly and the machine stops or faults.

Was man dagegen tut

Implement scheduled inspection and preventive replacement of air hoses based on condition (cracking, abrasion, fitting wear), route hoses away from pinch points and heat sources, and apply periodic functional testing, cleaning or proactive replacement of solenoid valves. Install upstream filtration, pressure regulation and monitoring to detect degradation before it causes a stop.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
0,4 % [0,1–1,2 %]
Erwarteter Anteil an der Verlustzeit
0,2 % [0,0–0,7 %]
Anteil an der Verlustzeit bei Auftreten
57 % [46–67 %]
Studien / Einheiten
120 / 162
Evidenzgrad
D

Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    0,4 % [0,0–1,6 %]18 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    0,4 % [0,0–1,3 %]44 Studien
  • Bier, Wein und Spirituosen
    0,4 % [0,0–1,8 %]16 Studien
  • Backwaren und Teigwaren
    0,5 % [0,0–1,9 %]0 Studien
  • Fleisch, Geflügel und Fisch
    0,5 % [0,0–1,7 %]6 Studien
  • Obst- und Gemüseverarbeitung
    0,5 % [0,0–1,9 %]4 Studien
  • Getreide- und Ölsaatenmüllerei
    0,5 % [0,0–1,9 %]6 Studien
  • Zucker und Süßwaren
    0,5 % [0,0–1,9 %]3 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    0,5 % [0,0–1,9 %]6 Studien
  • Futtermittel und Heimtiernahrung
    0,5 % [0,0–1,8 %]4 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    0,4 % [0,0–1,7 %]13 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

The pneumatic circuit that actuates the filling valves, cylinders or nozzles loses integrity because an air hose cracks, splits, abrades or disconnects from vibration and fatigue, or because a solenoid valve sticks, wears internally, or suffers a coil/electrical fault that blocks air flow. Without reliable compressed air delivery or switching, the filling actuators cannot move correctly and the machine stops or faults.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

SCADA/MES logs show low air pressure alarms or pressure-switch trips localized to the filling station, actuator position feedback that does not match the commanded state, cylinder or valve cycle timeouts, and the filling head registering a fault or stopped state while upstream/downstream stations continue briefly before starving or blocking. Repeated short stop events with the same pneumatic fault code are typical.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Implement scheduled inspection and preventive replacement of air hoses based on condition (cracking, abrasion, fitting wear), route hoses away from pinch points and heat sources, and apply periodic functional testing, cleaning or proactive replacement of solenoid valves. Install upstream filtration, pressure regulation and monitoring to detect degradation before it causes a stop.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Anzahl der Ereignisse: 2,00 events · laut Bericht: “Solenoid Air”
    Wörtliches Zitat anzeigen
    Solenoid Air 2
  2. Anzahl der Ereignisse: 5,00 events · laut Bericht: “Air Hose”
    Wörtliches Zitat anzeigen
    Air Hose 5