Reduced hammer mill throughput
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 63 % der Verlustzeit der Linie. Berichtet von 1 der 43 Studien, die sie beobachten konnten (spärliche Evidenz).
Was passiert
Worn hammers or screens, excessive feed moisture, or incorrect feed rate cause the hammer mill to process material below its rated capacity, so the drive runs at normal speed but delivers less ground product per unit time. The same underlying degradation also limits the output achieved while the mill is ramping up toward its target rate.
Was man dagegen tut
Implement scheduled inspection and replacement of hammers and screens based on wear condition, control incoming material moisture within the range suited to the mill, and tune the feed-rate control loop to match actual grinding capacity rather than a fixed setpoint.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 1,2 % [0,2–3,5 %]
- Erwarteter Anteil an der Verlustzeit
- 0,7 % [0,1–2,2 %]
- Anteil an der Verlustzeit bei Auftreten
- 63 % [50–75 %]
- Studien / Einheiten
- 43 / 48
- Evidenzgrad
- D
Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.
2Wahrscheinlichkeit nach Segment
- Milchprodukte1,3 % [0,1–5,3 %]5 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte1,4 % [0,1–5,4 %]1 Studie
- Bier, Wein und Spirituosen1,4 % [0,1–5,5 %]0 Studien
- Backwaren und Teigwaren1,4 % [0,1–5,5 %]0 Studien
- Fleisch, Geflügel und Fisch1,4 % [0,1–5,6 %]0 Studien
- Obst- und Gemüseverarbeitung1,3 % [0,1–5,3 %]2 Studien
- Getreide- und Ölsaatenmüllerei1,3 % [0,1–5,1 %]7 Studien
- Zucker und Süßwaren1,2 % [0,1–4,6 %]10 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel1,7 % [0,2–6,1 %]5 Studien
- Futtermittel und Heimtiernahrung1,3 % [0,1–4,9 %]6 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)1,3 % [0,1–4,9 %]7 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseWorn hammers or screens, excessive feed moisture, or incorrect feed rate cause the hammer mill to process material below its rated capacity, so the drive runs at normal speed but delivers less ground product per unit time. The same underlying degradation also limits the output achieved while the mill is ramping up toward its target rate.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseMES/SCADA shows mill motor load or current below the expected band for the running speed, throughput or product rate sensors trending under target while the machine state remains 'running', and extended time to reach stable rated output after start. No fault alarm is raised because the mill is operating, not stopped.
Gegenmaßnahme
Ingenieurpraktische HinweiseImplement scheduled inspection and replacement of hammers and screens based on wear condition, control incoming material moisture within the range suited to the mill, and tune the feed-rate control loop to match actual grinding capacity rather than a fixed setpoint.
4Quellen
- ANALISA OVERALL EQUIPMENT EFFECTIVENESS PADA MESIN HAMMER MILL DI INDUSTRI RUMPUT LAUT (2022)Quelle öffnenAnteil an der geplanten Zeit: 2,87 % · laut Bericht: “Speed Reduced losses”
Wörtliches Zitat anzeigen
Rata rata tahunan 2,73% 0,147% 15,214% 2,871% 1,565% 4,192%
- ANALISA OVERALL EQUIPMENT EFFECTIVENESS PADA MESIN HAMMER MILL DI INDUSTRI RUMPUT LAUT (2022)Quelle öffnenAnteil an der geplanten Zeit: 4,19 % · laut Bericht: “Reduced Yield”
Wörtliches Zitat anzeigen
Rata rata tahunan 2,73% 0,147% 15,214% 2,871% 1,565% 4,192%

