Roller arm/liner failure
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 58 % der Verlustzeit der Linie. Berichtet von 2 der 43 Studien, die sie beobachten konnten (spärliche Evidenz).
Was passiert
The roller arm or its mounted roller and liner wear, crack, or work loose under the cyclic loading and friction of the milling process, causing the roller to jam against its mating surface, come loose from the arm, or produce abnormal noise and vibration. Continued operation in this degraded state forces an unplanned stop so the arm, roller, or liner can be repaired or replaced before damage propagates to adjacent drive or frame components.
Was man dagegen tut
Implement condition-based inspection of roller arm bushings, fasteners, and liner wear with vibration and noise monitoring, and schedule preventive replacement of liners and arm components before they reach failure thresholds. Standardize torque/clamping procedures for roller-to-arm attachment to prevent loosening in service.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 1,0 % [0,2–3,0 %]
- Erwarteter Anteil an der Verlustzeit
- 0,6 % [0,1–1,7 %]
- Anteil an der Verlustzeit bei Auftreten
- 58 % [47–68 %]
- Studien / Einheiten
- 43 / 48
- Evidenzgrad
- D
Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.
2Wahrscheinlichkeit nach Segment
- Milchprodukte1,1 % [0,1–4,4 %]5 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte1,2 % [0,1–5,0 %]1 Studie
- Bier, Wein und Spirituosen1,2 % [0,1–4,9 %]0 Studien
- Backwaren und Teigwaren1,2 % [0,1–4,7 %]0 Studien
- Fleisch, Geflügel und Fisch1,2 % [0,1–4,4 %]0 Studien
- Obst- und Gemüseverarbeitung1,1 % [0,1–4,2 %]2 Studien
- Getreide- und Ölsaatenmüllerei1,1 % [0,1–4,1 %]7 Studien
- Zucker und Süßwaren1,0 % [0,1–3,9 %]10 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel1,7 % [0,2–6,4 %]5 Studien
- Futtermittel und Heimtiernahrung1,1 % [0,1–4,2 %]6 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)1,1 % [0,1–4,2 %]7 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseThe roller arm or its mounted roller and liner wear, crack, or work loose under the cyclic loading and friction of the milling process, causing the roller to jam against its mating surface, come loose from the arm, or produce abnormal noise and vibration. Continued operation in this degraded state forces an unplanned stop so the arm, roller, or liner can be repaired or replaced before damage propagates to adjacent drive or frame components.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseEquipment-failure stop codes tagged to the roller mill or roller arm asset, often preceded by abnormal vibration or motor-current/torque excursions and operator-logged noise alarms before the stop. Stop duration is consistent with mechanical repair/replacement (parts swap) rather than a brief clearance, and the event recurs on the same roller/arm position across runs.
Gegenmaßnahme
Ingenieurpraktische HinweiseImplement condition-based inspection of roller arm bushings, fasteners, and liner wear with vibration and noise monitoring, and schedule preventive replacement of liners and arm components before they reach failure thresholds. Standardize torque/clamping procedures for roller-to-arm attachment to prevent loosening in service.
4Quellen
- Reliability Measurement of Torque Transmission System for Spice Manufacturing Plant (2019)Quelle öffnenMittlere Ereignisdauer: 3,00 Hr · laut Bericht: “Roller arm failures/Liner replacement”
Wörtliches Zitat anzeigen
Roller arm failures/Liner replacement 2805.00 3.00 2794.5 13.5
- Reliability Measurement of Torque Transmission System for Spice Manufacturing Plant (2019)Quelle öffnenVerlustzeit: 3,00 Hr · laut Bericht: “V1: Roller arm jammed/Roller arm change”
Wörtliches Zitat anzeigen
08/30/16 016657 V1: Roller arm jammed/Roller arm change CMU 0 3 3
- Reliability Measurement of Torque Transmission System for Spice Manufacturing Plant (2019)Quelle öffnenVerlustzeit: 3,00 Hr · laut Bericht: “V1: Roller arm/Liner replacement”
Wörtliches Zitat anzeigen
01/06/16 014500 V1: Roller arm/Liner replacement CMP 0 3 3
- Reliability Measurement of Torque Transmission System for Spice Manufacturing Plant (2019)Quelle öffnenZeit zwischen Ereignissen: 2.795 Hr · laut Bericht: “Roller arm failures/Liner replacement”
Wörtliches Zitat anzeigen
Roller arm failures/Liner replacement 2805.00 3.00 2794.5 13.5
- Reliability Measurement of Torque Transmission System for Spice Manufacturing Plant (2019)Quelle öffnenMittlere Ereignisdauer: 13,5 Hr · laut Bericht: “Roller arm failures/Liner replacement”
Wörtliches Zitat anzeigen
Roller arm failures/Liner replacement 2805.00 3.00 2794.5 13.5
- Reliability Measurement of Torque Transmission System for Spice Manufacturing Plant (2019)Quelle öffnenZeit zwischen Ereignissen: 2.805 Hr · laut Bericht: “Roller arm failures/Liner replacement”
Wörtliches Zitat anzeigen
Roller arm failures/Liner replacement 2805.00 3.00 2794.5 13.5
- Reliability Measurement of Torque Transmission System for Spice Manufacturing Plant (2019)Quelle öffnenAnzahl der Ereignisse: 1,00 events · laut Bericht: “roller arm failure”
Wörtliches Zitat anzeigen
V1 had recorded one roller arm failure between 01/12/15 and 31/01/17, and had its grinding liner replaced 2 times in that period.
- Reliability Measurement of Torque Transmission System for Spice Manufacturing Plant (2019)Quelle öffnenVerlustzeit: 5,00 Hr · laut Bericht: “V4: Roller arm and liner change”
Wörtliches Zitat anzeigen
05/07/16 015728 V4: Roller arm and liner change CMP 0 5 5
- Reliability Measurement of Torque Transmission System for Spice Manufacturing Plant (2019)Quelle öffnenVerlustzeit: 22,0 Hr · laut Bericht: “V4: Center shaft service/Roller arm & liner change”
Wörtliches Zitat anzeigen
10/13/16 016972 V4: Center shaft service/Roller arm & liner change CMU 16 6 22
- Reliability Measurement of Torque Transmission System for Spice Manufacturing Plant (2019)Quelle öffnenVerlustzeit: 2,25 Hr · laut Bericht: “V4: Roller came loose from arm/Abnormal noise”
Wörtliches Zitat anzeigen
01/04/17 017546 V4: Roller came loose from arm/Abnormal noise CMU 0 2.25 2.25

