foratvise
Loslegen
Anlagenausfall (Störungen)

Roller arm locker plate bolt failure

Anlagenausfall (Störungen)VerfügbarkeitMahlen und Zerkleinern

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei etwa 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 58 % der Verlustzeit der Linie. Berichtet von 1 der 43 Studien, die sie beobachten konnten (spärliche Evidenz).

Was passiert

The bolt that secures the locker plate holding the roller arm in position is subjected to cyclic mechanical load and vibration during milling, causing it to loosen, fatigue and eventually break or shear, together with associated scrapper or stopper components. Once the bolt fails, the roller arm loses its fixed position and the roll gap or roll pressure can no longer be maintained correctly.

Was man dagegen tut

Implement periodic torque-checking and tightening of locker plate bolts as part of preventive maintenance, use bolts with appropriate fatigue rating and locking mechanisms (e.g., thread-locking compound or safety wire), and monitor vibration or roll gap trends to detect loosening before failure occurs.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
0,9 % [0,2–2,6 %]
Erwarteter Anteil an der Verlustzeit
0,5 % [0,1–1,5 %]
Anteil an der Verlustzeit bei Auftreten
58 % [47–68 %]
Studien / Einheiten
43 / 48
Evidenzgrad
D

Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    1,1 % [0,1–4,0 %]5 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    1,1 % [0,1–4,1 %]1 Studie
  • Bier, Wein und Spirituosen
    1,1 % [0,1–4,3 %]0 Studien
  • Backwaren und Teigwaren
    1,1 % [0,1–4,3 %]0 Studien
  • Fleisch, Geflügel und Fisch
    1,1 % [0,1–4,2 %]0 Studien
  • Obst- und Gemüseverarbeitung
    1,1 % [0,1–4,4 %]2 Studien
  • Getreide- und Ölsaatenmüllerei
    1,0 % [0,1–3,8 %]7 Studien
  • Zucker und Süßwaren
    1,0 % [0,1–3,7 %]10 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    1,5 % [0,2–5,6 %]5 Studien
  • Futtermittel und Heimtiernahrung
    1,1 % [0,1–4,0 %]6 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    1,0 % [0,1–3,9 %]7 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

The bolt that secures the locker plate holding the roller arm in position is subjected to cyclic mechanical load and vibration during milling, causing it to loosen, fatigue and eventually break or shear, together with associated scrapper or stopper components. Once the bolt fails, the roller arm loses its fixed position and the roll gap or roll pressure can no longer be maintained correctly.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

SCADA/MES logs show an unplanned stop event on a specific roller/mill unit tagged with a mechanical fault or bolt/locker plate alarm, often preceded by abnormal vibration, roll gap deviation or motor load fluctuation signals. The stop duration corresponds to a maintenance intervention window with roller arm or component replacement logged in the work order history.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Implement periodic torque-checking and tightening of locker plate bolts as part of preventive maintenance, use bolts with appropriate fatigue rating and locking mechanisms (e.g., thread-locking compound or safety wire), and monitor vibration or roll gap trends to detect loosening before failure occurs.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Zeit zwischen Ereignissen: 2.807 Hr · laut Bericht: “Roller arm locker plate bolt/scrapper failure”
    Wörtliches Zitat anzeigen
    Roller arm locker plate bolt/scrapper failure 2807.21 0.79 699.70 2.30
  2. Verlustzeit: 1,00 Hr · laut Bericht: “V4: Roller arm locker plate bolt broken”
    Wörtliches Zitat anzeigen
    12/08/15 014601 V4: Roller arm locker plate bolt broken CMU 0 1 1
  3. Verlustzeit: 0,580 Hr · laut Bericht: “V1: Roller arm (R63) locker plate bolt broken”
    Wörtliches Zitat anzeigen
    03/08/16 015266 V1: Roller arm (R63) locker plate bolt broken CMU 0 0.58 0.58
  4. Verlustzeit: 8,00 Hr · laut Bericht: “V4: Roller arm locker plate bolt broken/Roller arm (R21) change”
    Wörtliches Zitat anzeigen
    12/04/15 014523 V4: Roller arm locker plate bolt broken/Roller arm (R21) change CMU 4 4 8
  5. Mittlere Ereignisdauer: 0,790 Hr · laut Bericht: “Roller arm locker plate bolt/scrapper failure”
    Wörtliches Zitat anzeigen
    Roller arm locker plate bolt/scrapper failure 2807.21 0.79 699.70 2.30
  6. Anzahl der Ereignisse: 2,00 events · laut Bericht: “roller/scrapper failure”
    Wörtliches Zitat anzeigen
    V1 had only recorded 2 failures from operating 351 days.
  7. Verlustzeit: 1,58 Hr · laut Bericht: “roller/scrapper failure”
    Wörtliches Zitat anzeigen
    These intermittent stoppages caused by such failure had accumulated 1.58, and 18.41 hour of stoppage time for V1 and V4 respectively.
  8. Zeit zwischen Ereignissen: 700 Hr · laut Bericht: “Roller arm locker plate bolt/scrapper failure”
    Wörtliches Zitat anzeigen
    Roller arm locker plate bolt/scrapper failure 2807.21 0.79 699.70 2.30
  9. Mittlere Ereignisdauer: 2,30 Hr · laut Bericht: “Roller arm locker plate bolt/scrapper failure”
    Wörtliches Zitat anzeigen
    Roller arm locker plate bolt/scrapper failure 2807.21 0.79 699.70 2.30
  10. Anzahl der Ereignisse: 7,00 events · laut Bericht: “roller/scrapper failure”
    Wörtliches Zitat anzeigen
    During the same period, V4 had encountered the same failure 5 times extra, totalling a 7 failure.
  11. Verlustzeit: 18,4 Hr · laut Bericht: “roller/scrapper failure”
    Wörtliches Zitat anzeigen
    These intermittent stoppages caused by such failure had accumulated 1.58, and 18.41 hour of stoppage time for V1 and V4 respectively.
  12. Anteil an den Verlustereignissen: 43,8 % · laut Bericht: “locker plate bolt damage”
    Wörtliches Zitat anzeigen
    43.75% of failure in V4 mill is caused by locker plate bolt damage, the higher rate of such failure is due to the type of drive employed in V4 mill.
  13. Verlustzeit: 0,330 Hr · laut Bericht: “V4: R49 Locker plate bolt broken”
    Wörtliches Zitat anzeigen
    02/19/16 015158 V4: R49 Locker plate bolt broken CMU 0 0.33 0.33
  14. Verlustzeit: 0,500 Hr · laut Bericht: “V4: Roller arm (R49) locker plate bolt broken”
    Wörtliches Zitat anzeigen
    03/09/16 015231 V4: Roller arm (R49) locker plate bolt broken CMU 0 0.5 0.5
  15. Verlustzeit: 1,00 Hr · laut Bericht: “V4: Roller arm (R49) locker plate bolt broken”
    Wörtliches Zitat anzeigen
    03/29/16 015448 V4: Roller arm (R49) locker plate bolt broken CMU 0 1 1
  16. Verlustzeit: 0,330 Hr · laut Bericht: “V4: R49 locker plate holding bolts loosen”
    Wörtliches Zitat anzeigen
    04/06/16 015496 V4: R49 locker plate holding bolts loosen CMU 0 0.33 0.33
  17. Verlustzeit: 5,00 Hr · laut Bericht: “V4: Roller arm locker plate bolt broken/stopper broken”
    Wörtliches Zitat anzeigen
    07/01/16 016185 V4: Roller arm locker plate bolt broken/stopper broken CMU 0 5 5