Non-optimized changeover procedure
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei weniger als 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 56 % der Verlustzeit der Linie. Berichtet von 0 der 120 Studien, die sie beobachten konnten (spärliche Evidenz).
Was passiert
Changeover tasks on the filler are performed largely as sequential, machine-stopped (internal) steps rather than being split into parallel or pre-staged (external) activities, and adjustments are not standardized across operators. This lack of structured methodology extends the time between the last good unit of one run and the first good unit of the next.
Was man dagegen tut
Apply SMED methodology: classify and separate internal versus external setup activities, convert as many internal steps as possible into external ones performed while the line still runs, standardize and simplify adjustments with quick-change fixtures and pre-staged tooling, and validate the new sequence through time-and-motion studies and operator training.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,3 % [0,1–1,0 %]
- Erwarteter Anteil an der Verlustzeit
- 0,2 % [0,0–0,6 %]
- Anteil an der Verlustzeit bei Auftreten
- 56 % [43–67 %]
- Studien / Einheiten
- 120 / 162
- Evidenzgrad
- D
Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,4 % [0,0–1,4 %]18 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte0,3 % [0,0–1,2 %]44 Studien
- Bier, Wein und Spirituosen0,4 % [0,0–1,5 %]16 Studien
- Backwaren und Teigwaren0,4 % [0,0–1,7 %]0 Studien
- Fleisch, Geflügel und Fisch0,4 % [0,0–1,6 %]6 Studien
- Obst- und Gemüseverarbeitung0,4 % [0,0–1,6 %]4 Studien
- Getreide- und Ölsaatenmüllerei0,4 % [0,0–1,5 %]6 Studien
- Zucker und Süßwaren0,4 % [0,0–1,7 %]3 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel0,4 % [0,0–1,5 %]6 Studien
- Futtermittel und Heimtiernahrung0,4 % [0,0–1,6 %]4 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)0,4 % [0,0–1,5 %]13 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseChangeover tasks on the filler are performed largely as sequential, machine-stopped (internal) steps rather than being split into parallel or pre-staged (external) activities, and adjustments are not standardized across operators. This lack of structured methodology extends the time between the last good unit of one run and the first good unit of the next.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseMES/SCADA logs show an extended changeover or setup machine-state duration on the filler, with multiple sequential sub-states (teardown, tool change, adjustment, trial run) and manual confirmation events bridging the transition; the changeover time distribution shows a long tail not explained by format complexity alone, and neighboring stations remain idle or blocked during the stop.
Gegenmaßnahme
Ingenieurpraktische HinweiseApply SMED methodology: classify and separate internal versus external setup activities, convert as many internal steps as possible into external ones performed while the line still runs, standardize and simplify adjustments with quick-change fixtures and pre-staged tooling, and validate the new sequence through time-and-motion studies and operator training.
4Quellen
- Verlustzeit: 16,0 min · laut Bericht: “SMED and related improvements”
Wörtliches Zitat anzeigen
Therefore,the total reduction in changeover time due to SMED and related improvements was 16 min.

