Homogenisieren
High-pressure valve homogenization of pasteurized milk
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Homogenisieren kann höchstens 98 von je 100 geplanten Stunden nutzen. Der Rest entfällt auf Grenzen, die kein Werk vermeiden kann.
- 98höchstens nutzbar
- 2sind physikalische Grenze
Die drei Grenzen, die das festlegen
Laufzeit: bis 98 %
Der Rest sind Stillstände, die Physik oder Vorschrift erzwingen: Reinigung, Umrüsten, Abtauen.
Geschwindigkeit: bis 100 %
Wie nah an ihrer Höchstgeschwindigkeit sie laufen kann, ohne Produkt oder Anlage zu schädigen.
Gutprodukt: bis 100 %
Ein Teil des Produkts liegt auch bei gut beherrschtem Prozess außerhalb der Spezifikation.
Technisches Detail
Unsicherheitsintervalle, physikalische Modelle je Station und Quellen, für alle, die jede Zahl prüfen möchten.
1Szenario
Standardized whole milk is pumped by a piston pump through a two-stage homogenizing valve in line with the pasteurizer. The fat globules are broken from about 3.5 µm to below 1 µm so that the packaged milk, stored cold, passes the creaming test (48 h quiescent storage, the fat of the top 100 mL of 1 000 mL may not exceed the fat of the rest by more than 1/0.9). The homogenizer is cleaned in place with the pasteurizer once per day of use. Homogenization of other emulsions (cream, ice-cream mix, juices with pulp) follows the same structure but is outside the numbers of this model.
2Ergebnisse
- Serum viscosity at the storage temperature2,82 mPa·s
- Log standard deviation of the homogenized globule-size distribution0,559 [0,520–0,601]
- Largest volume-weighted mean rise distance that passes the creaming test1,98 [1,51–2,45] mm
- Largest volume-weighted median globule diameter that passes the creaming test0,636 [0,519–0,778] um
- Surface-weighted (Sauter) mean diameter at the specification0,544 [0,441–0,669] um
- Increase of the fat/serum interfacial area from native to specification globules6,59 [5,36–8,13]
- Minimum homogenizing pressure of the reference two-stage valve that passes the creaming test20,4 [15,9–26,5] MPa
- Pressure set point of the capable process (minimum plus z standard deviations)21,9 [17,5–28,4] MPa
- Tension of the casein-covered milk-fat/serum interface10,3 [8,1–12,6] mN/m
- TheoretischThermodynamic minimum: free energy of the new interface0,00364 [0,00248–0,00518] kJ/kg
- Hydraulic work at the minimum pressure of the reference valve (p/rho)19,9 [15,5–25,7] kJ/kg
- Electricity at the set-point pressure of the reference valve (drive efficiency of the documented conventional machine)23,2 [18,5–30,0] kJ/kg
- Beste verfügbare TechnikElectricity of the advanced-design homogenizer (97 bar, BAT reference document)10,5 kJ/kg
- Best dokumentiertElectricity of the efficient-design homogenizer (135 bar, BAT reference document)14,6 kJ/kg
- TypischElectricity of the conventional homogenizer (200 bar, BAT reference document)21,2 kJ/kg
- Hydraulic power over electric power of the documented conventional homogenizer0,920
- Thermodynamic minimum divided by the typical electricity1,72 × 10⁻⁴ [1,17 × 10⁻⁴–2,45 × 10⁻⁴]
- Temperature rise of the milk per MPa of pressure drop (all hydraulic work dissipated)0,248 [0,244–0,254] K/MPa
- Temperature rise at the set-point pressure5,45 [4,35–7,07] K
- Bernoulli velocity in the valve gap at the set-point pressure207 [185–235] m/s
- Milk homogenized per kW of drive at the set-point pressure of the reference valve151 [117–189] L/h/kW
- TheoretischMaximum yield (no stream split)1,00
- Share of milk homogenized below the minimum pressure (fails the creaming test)0,00135 [0,00025–0,00576]
- TheoretischMaximum availability (daily cleaning and wear-part exchange)0,9834 [0,9778–0,9876]
- TheoretischMaximum performance factor (positive-displacement pump at its rated flow)1,00
- TheoretischMaximum OEE quality factor (creaming test)0,9987 [0,9942–0,9997]
- TheoretischPhysics-bounded OEE0,982 [0,975–0,986]
3Obergrenzen je Dimension
- Theoretisch
- Beste verfügbare Technik
- Best dokumentiert
- Typisch
- TheoretischThermodynamic minimum: free energy of the new interface0,00364 [0,00248–0,00518] kJ/kg
- Beste verfügbare TechnikElectricity of the advanced-design homogenizer (97 bar, BAT reference document)10,5 kJ/kg
- Best dokumentiertElectricity of the efficient-design homogenizer (135 bar, BAT reference document)14,6 kJ/kg
- TypischElectricity of the conventional homogenizer (200 bar, BAT reference document)21,2 kJ/kg
- TheoretischMaximum yield (no stream split)1,00
- TheoretischMaximum availability (daily cleaning and wear-part exchange)0,9834 [0,9778–0,9876]
- TheoretischMaximum performance factor (positive-displacement pump at its rated flow)1,00
- TheoretischMaximum OEE quality factor (creaming test)0,9987 [0,9942–0,9997]
- TheoretischPhysics-bounded OEE0,982 [0,975–0,986]
4Verlustkaskade
- TheoretischBeste verfügbare TechnikEnergie je Produkteinheit0,00364 [0,00248–0,00518] kJ/kg → 10,5 kJ/kg (Abstand 10,5 kJ/kg)
The thermodynamic minimum is the free energy of the new fat/serum interface, gamma times the new area: a few joules per kilogram of milk. A valve homogenizer dissipates the whole hydraulic work p/rho in the turbulent jet behind the gap (one kelvin of heating per 4 MPa); only the eddies of the globule size break globules, so more than 99.9 % of the work ends as heat. The advanced valve design of the BAT reference document reaches the same homogenization effect at 97 bar by shaping the gap so that more of the turbulence acts at the globule scale.
- Beste verfügbare TechnikBest dokumentiertEnergie je Produkteinheit10,5 kJ/kg → 14,6 kJ/kg (Abstand 4,06 kJ/kg)
The efficient design needs 135 bar for the same effect; the difference to the advanced design is valve geometry, applicable only above about 15 000 L/h.
- Best dokumentiertTypischEnergie je Produkteinheit14,6 kJ/kg → 21,2 kJ/kg (Abstand 6,58 kJ/kg)
A conventional valve needs 200 bar. The creaming test in this model asks for a median globule diameter close to the one a conventional two-stage valve gives at 20 MPa, which is why the conventional pressure and the computed minimum pressure of the reference valve nearly coincide; partial homogenization (cream plus a small share of skim milk) cuts the pumped volume and the power by about two thirds.
5Physikalisch begrenzte OEE
- Belegungszeit (ideal)1,000
- VerfügbarkeitFaktor 0,9834 [0,9778–0,9876]0,983 (−0,017)
- LeistungFaktor 1,000,983 (−0,000)
- QualitätFaktor 0,9987 [0,9942–0,9997]0,982 (−0,001)
- Physikalisch begrenzte OEE0,982 [0,975–0,986]
6Vollständige Herleitung
Scope. Standardized whole milk is pumped by a piston pump through a two-stage homogenizing valve in line with the pasteurizer, at 55–80 °C. The fat globules are broken from about 3.5 µm to below 1 µm so that the packaged milk, stored at or below 7 °C, passes the creaming test: after 48 h of quiescent storage of 1 000 mL, 0.9 times the fat content of the top 100 mL must be below the fat content of the rest. Symbols and their values, units, uncertainty distributions and sources are listed in the parameter table generated from config/physics/homogenization.yaml.
1. Mass balance — maximum yield
Homogenization has no phase change, no reaction and no stream split: every kilogram that enters the pump leaves the valve. The steady-state yield is exactly 1. The product–water mixing zones at start-up and shut-down belong to the pasteurization line in which the homogenizer sits and are counted in that model, so
2. The quality law — what the creaming test demands
Creaming. Homogenized globules rise individually (they no longer cluster by cold agglutination), at the Stokes velocity
- , — densities of milk (1.028 g/cm³, lower end of the documented 1.028–1.038) and of milk fat (0.93 g/cm³).
- — declared reduction (0.6–1.0) of the density difference by the casein layer that covers the new globule surface; casein is denser than fat.
- — serum viscosity at the storage temperature = 7 °C (legal maximum for pasteurized milk): the handbook value at about 35 °C (1.42 mPa·s) scaled with the viscosity of water (IAPWS through CoolProp), about 2.8 mPa·s.
The test as a bound. In a column of height the top layer has height . A globule class that rises a distance in the test time moves fat into the top layer (relative concentration ) and leaves a cream-free band at the bottom of the lower layer (relative concentration ). Summed over the volume distribution, with the volume-weighted mean rise, the test with = 0.9 passes while
For = 0.2 m, = 1.98 mm. Because and ,
for a log-normal volume distribution with median and log standard deviation . The test therefore fixes the largest allowed median diameter — about 0.64 µm with the point values.
Width of the homogenized distribution. Milk homogenized in two stages at 20 MPa has a volume median of 0.648 µm (the largest of the medians reported for 20, 25 and 30 MPa, all size parameters decreasing with pressure) and 21.87 % of its fat volume in globules larger than 1 µm. For a log-normal distribution the share above 1 µm is , which gives .
3. Size law and minimum pressure of the reference valve
In the turbulent jet behind the valve gap, the largest stable globule is set by the balance between the dynamic pressure of eddies of its own size and the Laplace pressure (Kolmogorov–Hinze). In the inertial subrange this gives , where is the power dissipated per unit mass. The jet velocity is the Bernoulli velocity and for a fixed gap geometry , hence
Measured series in the industrial range fall more steeply: the coarse-tail shares of the 20, 25 and 30 MPa columns of the same table correspond, at constant width, to exponents of 0.87 and 1.08. The model writes
with declared uniform between 0.6 and 1.1. Because the specification diameter lies close to the reference diameter, is insensitive to : about 20 MPa for the reference two-stage valve. This minimum belongs to that valve geometry. The BAT reference document shows that other geometries reach the same homogenization effect at 135 bar (efficient design) and 97 bar (advanced design) instead of 200 bar (conventional), so the pressure is a technology variable, not a physical constant; that is why the energy ceilings below the theoretical one are documented values (Section 4).
4. Energy balance — minimum energy per unit of product
Thermodynamic minimum. Homogenization changes no chemistry; it creates interface. The reversible work is the free energy of the new fat/serum interface,
- — tension of the casein-covered interface, the tension of purified milk fat against water (30.50 mN/m) minus the surface pressure of micellar casein at a milk-like concentration of 2.5 % (20.16 mN/m): 10.34 mN/m.
- — fat content of the milk (declared 3.0–4.0 %).
- — Sauter diameter of native globules from their specific surface (1.8 m²/g fat): 3.58 µm.
- — Sauter diameter at the specification (about 0.54 µm).
The new area is about 350 m² per kg of milk — a 6.6-fold increase of the interface, slightly above the four- to six-fold increase the handbook states for typical homogenization, consistent with the test requiring fine globules — and is a few joules per kilogram.
Hydraulic work and heating. A positive-displacement pump delivers the work per kilogram, and the valve dissipates all of it in the jet; the milk warms by
0.25 K per MPa with = 3.915 kJ/(kg K) — the handbook's rule of 1 °C per 4 MPa. At the minimum pressure the hydraulic work is about 20 kJ/kg; with the drive efficiency of the documented conventional machine ( = 200 bar × 25 000 L/h / 151 kW = 0.92), the electricity at the set-point pressure is about 23 kJ/kg. These two values carry no ceiling label (they belong to the reference valve).
Ratio to practice. divided by the typical electricity is about : the handbook's statement that less than 1 % of the energy is used for homogenization is an understatement. The rest is turbulent dissipation at scales larger than the globules, heat in the valve and drive losses.
The four energy ceilings. Theoretical: . Best available technique: advanced valve design, 75 kW at 25 000 L/h (97 bar), 10.5 kJ/kg. Documented: efficient design, 104 kW (135 bar), 14.6 kJ/kg. Typical: conventional design, 151 kW (200 bar), 21.2 kJ/kg. All three electric values are converted with the milk density and are for the same homogenization effect (75 % NIZO).
5. Rate-limiting step — time and throughput
Globule break-up in the gap takes microseconds (the handbook gives 10–15 µs; the gap velocity at the set point is about 210 m/s, within the documented 100–400 m/s), so kinetics are not limiting. The homogenizer is a positive-displacement pump: its throughput is the pump displacement, and the physics enters through the power it needs. The throughput per kW of drive at the set point of the reference valve,
about 150 L/h per kW, is reported without a ceiling label because it depends on the valve. A homogenizer at its rated flow has an OEE performance factor of 1.
6. Process capability — quality ceiling
The homogenizing pressure under control is modelled as normal with standard deviation (valve wear, pump pulsation) around a set point standard deviations above the minimum:
Milk homogenized below fails the creaming test and is reworked. The margin costs of hydraulic work per kilogram, a small amount.
7. Unavoidable stops — maximum availability
Two stops are forced. Hygiene regulation requires milk equipment to be cleaned at least once each day used; the homogenizer is cleaned in place with the pasteurizer, and the duration is taken through a parameter link from the cleaning model (output cip_time_min). That model is valid for recirculated pipe and plate circuits; the pump block and valve are outside its validity, so the linked duration is a lower bound. The homogenizing valve and plunger seals wear under the pressure load and must be exchanged (interval and duration declared; the BAT reference document notes that lower pressures lengthen the interval):
8. Physics-bounded OEE
Scope of the bound. The theoretical label of means physics-bounded under the declared scenario: the ceiling follows from the physics of the operation for the declared product, equipment and schedule, and it is a bound only conditional on those declarations. It follows the common definition of all models: counts only stops required by regulation or forced by a physical mechanism, at their physical minimum duration, plus the start-up they force; is the ratio of the physics-limited ideal cycle to the cycle of the capable process; is the share of conforming units, and mass losses of conforming product are reported only as yield.
The result, with the Monte Carlo interval over the declared uncertainty of every input, is reported in the output table. The homogenizer sits in the pasteurization line; when both are modelled as one line, the daily cleaning is the same stop and must be counted once.
9. Assumptions and validity
See the assumption and validity lists generated from the configuration file. The specification diameter is most sensitive to the declared density reduction by the casein coat and to the height of the test column; the minimum pressure inherits that sensitivity, the energy ceilings below the theoretical one do not (they are documented). Cream, ice-cream mix and ultra-high-pressure homogenization follow other size laws and are outside the numbers of this model.
References
- Tetra Pak Processing Systems. Dairy Processing Handbook, chapters 7.3 Homogenizers, 7.2 Centrifugal separators and milk standardization, and 2 The chemistry of milk (online edition).
- Kim, S.-C., Yun, S.-Y., Ahn, N.-H., Kim, S.-M., Imm, J.-Y. (2020). Effect of homogenization pressure on plasmin activity and mechanical stress-induced fat aggregation of commercially sterilized ultra high temperature milk during storage. Food Science of Animal Resources, 40(5), 734–745. doi:10.5851/kosfa.2020.e48
- Yan, G., Li, Y., Wang, S., Li, Y., Zhang, L., Yan, J., Sun, Y. (2024). Oil–water interfacial behaviour of different caseins and stability of emulsions: effect of micelle content and caseins concentrations. Food Chemistry: X, 23, 101784. doi:10.1016/j.fochx.2024.101784
- Lopez, C., Cauty, C., Guyomarc'h, F. (2015). Organization of lipids in milks, infant milk formulas and various dairy products: role of technological processes and potential impacts. Dairy Science & Technology, 95, 863–893. doi:10.1007/s13594-015-0263-0
- Hinze, J. O. (1955). Fundamentals of the hydrodynamic mechanism of splitting in dispersion processes. AIChE Journal, 1(3), 289–295. doi:10.1002/aic.690010303
- Kolmogorov, A. N. (1991). The local structure of turbulence in incompressible viscous fluid for very large Reynolds numbers. Proceedings of the Royal Society A, 434, 9–13 (translation of the 1941 paper). doi:10.1098/rspa.1991.0075
- U.S. Food and Drug Administration. Grade "A" Pasteurized Milk Ordinance, 2023 Revision.
- European Commission, Joint Research Centre. Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries, 2019.
- Bell, I. H., Wronski, J., Quoilin, S., Lemort, V. (2014). Pure and pseudo-pure fluid thermophysical property evaluation and the open-source thermophysical property library CoolProp. Industrial & Engineering Chemistry Research, 53, 2498–2508. doi:10.1021/ie4033999
7Parameter und Herkunft
- 3,5 %
Fat content of the standardized milk
Szenario · Gleichverteilt 3 bis 4 %
Deklarierte AnnahmeDeclared standardized whole milk.
- 930 kg/m³
Density of milk fat (15.5 °C)
Stoffwert · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
the lightest (density at 15.5 °C = 0.93 g/cm3)Dairy Processing Handbook, chapter 2: The chemistry of milk (öffnet in neuem Tab). Tetra Pak Processing Systems AB (online edition, openly readable), 2026. Tetra Pak Dairy Processing Handbook, online edition, chapter 2 (read 2026-11-15)
- 1.028 kg/m³
Density of milk
Stoffwert · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
The density of cows’ milk normally varies between 1.028 and 1.038 g/cm3, depending on its composition.Dairy Processing Handbook, chapter 2: The chemistry of milk (öffnet in neuem Tab). Tetra Pak Processing Systems AB (online edition, openly readable), 2026. Tetra Pak Dairy Processing Handbook, online edition, chapter 2 (read 2026-11-15)
- 0,8
Reduction of the globule–serum density difference by the casein layer adsorbed on homogenized globules
Szenario · Gleichverteilt 0,6 bis 1
Deklarierte AnnahmeDeclared assumption: newly formed globule surfaces are covered by casein micelles and fragments, which are denser than fat, so the effective density difference of small homogenized globules is below that of bare fat; no open source with a verbatim value was found.
- 1,42 mPa·s
Viscosity of the milk serum in the handbook's reference state
Stoffwert · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
h = 1.42 cP (centipoise) = 1.42 x 10–3 kg/m, sDairy Processing Handbook, chapter 7.2: Centrifugal separators and milk standardization (öffnet in neuem Tab). Tetra Pak Processing Systems AB (online edition, openly readable), 2026. Tetra Pak Dairy Processing Handbook, online edition, chapter 7.2 (read 2026-11-15)
- 35 °C
Temperature of the handbook's reference state
Stoffwert · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
The following average values apply at an ambient temperature of about 35 °CDairy Processing Handbook, chapter 7.2: Centrifugal separators and milk standardization (öffnet in neuem Tab). Tetra Pak Processing Systems AB (online edition, openly readable), 2026. Tetra Pak Dairy Processing Handbook, online edition, chapter 7.2 (read 2026-11-15)
- 7 °C
Maximum storage temperature of pasteurized milk (temperature of the creaming test)
Regulatorisch · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
GRADE “A” PASTEURIZED MILK AND/OR MILK PRODUCTS Temperature Cooled to 7°C (45°F) or less and maintained thereat.Grade "A" Pasteurized Milk Ordinance, 2023 Revision (öffnet in neuem Tab). U.S. Department of Health and Human Services, Public Health Service, Food and Drug Administration, 2023. S. 57. PMO 2023 Revision
- 48 h
Quiescent storage time of the creaming test
Regulatorisch · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
a sample of 1,000 ml is stored for 48 hours, after which the fat content of the top 100 ml is determinedDairy Processing Handbook, chapter 7.3: Homogenizers (öffnet in neuem Tab). Tetra Pak Processing Systems AB (online edition, openly readable), 2026. Tetra Pak Dairy Processing Handbook, online edition, chapter 7.3 (read 2026-11-15)
- 1.000 mL
Sample volume of the creaming test
Regulatorisch · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
a sample of 1,000 ml is stored for 48 hours, after which the fat content of the top 100 ml is determinedDairy Processing Handbook, chapter 7.3: Homogenizers (öffnet in neuem Tab). Tetra Pak Processing Systems AB (online edition, openly readable), 2026. Tetra Pak Dairy Processing Handbook, online edition, chapter 7.3 (read 2026-11-15)
- 100 mL
Top volume analysed in the creaming test
Regulatorisch · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
a sample of 1,000 ml is stored for 48 hours, after which the fat content of the top 100 ml is determinedDairy Processing Handbook, chapter 7.3: Homogenizers (öffnet in neuem Tab). Tetra Pak Processing Systems AB (online edition, openly readable), 2026. Tetra Pak Dairy Processing Handbook, online edition, chapter 7.3 (read 2026-11-15)
- 0,9
Pass criterion of the creaming test: f times the top fat content must be below the bottom fat content
Regulatorisch · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
homogenization is considered to be sufficient if 0.9 times the top fat content is less than the bottom fat contentDairy Processing Handbook, chapter 7.3: Homogenizers (öffnet in neuem Tab). Tetra Pak Processing Systems AB (online edition, openly readable), 2026. Tetra Pak Dairy Processing Handbook, online edition, chapter 7.3 (read 2026-11-15)
- 0,2 m
Height of the liquid column of the creaming-test sample
Szenario · Gleichverteilt 0,15 bis 0,25 m
Deklarierte AnnahmeDeclared geometry of a one-litre container; a taller column makes the test easier to pass.
- 0,648 um
Volume-weighted median globule diameter after two-stage homogenization at the reference pressure (largest of the documented medians, lowest pressure)
Technik · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
The median particle diameter (D 50 ) of raw milk was about 3.41 μm and it was reduced by 0.358 to 0.648 μm by two-stage homogenization.Effect of Homogenization Pressure on Plasmin Activity and Mechanical Stress-Induced Fat Aggregation of Commercially Sterilized Ultra High Temperature Milk during Storage (Kim, Yun, Ahn, Kim, Imm; Food Science of Animal Resources 40(5): 734-745) (öffnet in neuem Tab). Korean Society for Food Science of Animal Resources (open access, CC BY-NC 3.0); full text served by Europe PMC, 2020. doi:10.5851/kosfa.2020.e48; PMC7492180
- 20 MPa
Reference homogenizing pressure of the documented size distribution
Technik · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
All particle size parmeters (D 50 , D 3,2 , and D 4,3 ) of milk fat globules were significantly decreased as homogenization pressure increased from 20 to 30 MPaEffect of Homogenization Pressure on Plasmin Activity and Mechanical Stress-Induced Fat Aggregation of Commercially Sterilized Ultra High Temperature Milk during Storage (Kim, Yun, Ahn, Kim, Imm; Food Science of Animal Resources 40(5): 734-745) (öffnet in neuem Tab). Korean Society for Food Science of Animal Resources (open access, CC BY-NC 3.0); full text served by Europe PMC, 2020. doi:10.5851/kosfa.2020.e48; PMC7492180
- 21,87 %
Volume share of globules larger than 1 µm after homogenization at the reference pressure
Technik · Normalverteilt, Std.-Abw. 0,84 %
Verifiziertes ZitatWörtliches Zitat anzeigen
Homogenization pressure (MPa) 20 25 30 0 <0.5 μm 45.29±0.89 55.12±4.20 67.84±0.15 0.5–1 μm 32.84±0.23 31.80±2.66 26.25±0.10 >1 μm 21.87±0.84 13.08±1.60 5.91±0.07Effect of Homogenization Pressure on Plasmin Activity and Mechanical Stress-Induced Fat Aggregation of Commercially Sterilized Ultra High Temperature Milk during Storage (Kim, Yun, Ahn, Kim, Imm; Food Science of Animal Resources 40(5): 734-745) (öffnet in neuem Tab). Korean Society for Food Science of Animal Resources (open access, CC BY-NC 3.0); full text served by Europe PMC, 2020. doi:10.5851/kosfa.2020.e48; PMC7492180
- 0,85
Exponent of the decrease of globule size with homogenizing pressure, d ∝ p^-b
Szenario · Gleichverteilt 0,6 bis 1,1
Deklarierte AnnahmeDeclared range: 0.6 is the inertial-turbulence (Kolmogorov–Hinze) exponent derived in physics_docs/homogenization.en.md, section 3; fitting the coarse-tail shares of the 20, 25 and 30 MPa columns of the same table with a constant log-normal width gives 0.87 and 1.08. The minimum pressure is insensitive to b because the specification diameter lies close to the reference diameter.
- 0,5 MPa
Standard deviation of the homogenizing pressure under control
Szenario · Gleichverteilt 0,25 bis 1 MPa
Deklarierte AnnahmeProcess-capability assumption (valve wear, pump pulsation); replace with the plant's measured value.
- 3
Margin of the pressure set point above the minimum pressure, in standard deviations
Szenario · Gleichverteilt 2,5 bis 3,5
Deklarierte AnnahmeOperating choice; the point value 3 is the centre of the declared range 2.5-3.5.
- 30,5 mN/m
Interfacial tension between purified milk fat and water
Stoffwert · Normalverteilt, Std.-Abw. 0,5 mN/m
Verifiziertes ZitatWörtliches Zitat anzeigen
γ 0 is the interfacial tension between AMF and water after purification (30.50 ± 0.50 mN/m)Oil-water interfacial behaviour of different caseins and stability of emulsions: Effect of micelle content and caseins concentrations (Yan, Li, Wang, Li, Zhang, Yan et al.; Food Chemistry: X 23: 101784) (öffnet in neuem Tab). Elsevier (open access, CC BY-NC-ND 4.0); full text served by Europe PMC, 2024. doi:10.1016/j.fochx.2024.101784; PMC11403417
- 20,16 mN/m
Surface pressure of micellar casein at the milk-fat/water interface at a milk-like casein concentration (2.5 %)
Stoffwert · Normalverteilt, Std.-Abw. 1,02 mN/m
Verifiziertes ZitatWörtliches Zitat anzeigen
whereas at a concentration of 2.5 %, it increased to 20.16 ± 1.02 mN/mOil-water interfacial behaviour of different caseins and stability of emulsions: Effect of micelle content and caseins concentrations (Yan, Li, Wang, Li, Zhang, Yan et al.; Food Chemistry: X 23: 101784) (öffnet in neuem Tab). Elsevier (open access, CC BY-NC-ND 4.0); full text served by Europe PMC, 2024. doi:10.1016/j.fochx.2024.101784; PMC11403417
- 4,4 um
Volume-weighted mean diameter of native milk fat globules
Stoffwert · Normalverteilt, Std.-Abw. 0,2 um
Verifiziertes ZitatWörtliches Zitat anzeigen
The size distribution of milk fat globules ranges from 1 to 12 μm with a mean volume-weighted diameter of 4.4 ± 0.2 μm (surface area = 1.8 m 2 .g -1 fat).Organization of lipids in milks, infant milk formulas and various dairy products: role of technological processes and potential impacts (Lopez, Cauty, Guyomarc'h; Dairy Science & Technology 95: 863-893) (öffnet in neuem Tab). Springer / INRA (open access); full text served by Europe PMC, 2015. doi:10.1007/s13594-015-0263-0; PMC4641158
- 1,8 m²/g
Specific surface of native fat globules per gram of fat
Stoffwert · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
The size distribution of milk fat globules ranges from 1 to 12 μm with a mean volume-weighted diameter of 4.4 ± 0.2 μm (surface area = 1.8 m 2 .g -1 fat).Organization of lipids in milks, infant milk formulas and various dairy products: role of technological processes and potential impacts (Lopez, Cauty, Guyomarc'h; Dairy Science & Technology 95: 863-893) (öffnet in neuem Tab). Springer / INRA (open access); full text served by Europe PMC, 2015. doi:10.1007/s13594-015-0263-0; PMC4641158
- 3,915 kJ/kg/K
Specific heat capacity of whole milk at the homogenizing temperature (composition model of Choi and Okos, 65 °C)
Stoffwert · Normalverteilt, Std.-Abw. 0,04 kJ/kg/K
Berechnetmeo.physics.foodprops.cp(composition=whole_milk, T=65 °C) = 3.915 kJ/(kg K); composition and coefficients are cited in config/physics/food_properties.yaml.
- 200 bar
Homogenizing pressure of a conventional homogenizer for the documented homogenization effect
Vergleichswert · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
Homogenisation pressure (bar) 200 135 97 Electric power needed (kW) 151 104 75Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 405. EUR 29978 EN; JRC118627; doi:10.2760/243911
- 135 bar
Homogenizing pressure of an efficient-design homogenizer for the same effect
Vergleichswert · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
Homogenisation pressure (bar) 200 135 97 Electric power needed (kW) 151 104 75Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 405. EUR 29978 EN; JRC118627; doi:10.2760/243911
- 97 bar
Homogenizing pressure of an advanced-design homogenizer for the same effect
Vergleichswert · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
Homogenisation pressure (bar) 200 135 97 Electric power needed (kW) 151 104 75Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 405. EUR 29978 EN; JRC118627; doi:10.2760/243911
- 151 kW
Electric power of the conventional homogenizer
Vergleichswert · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
Homogenisation pressure (bar) 200 135 97 Electric power needed (kW) 151 104 75Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 405. EUR 29978 EN; JRC118627; doi:10.2760/243911
- 104 kW
Electric power of the efficient-design homogenizer
Vergleichswert · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
Homogenisation pressure (bar) 200 135 97 Electric power needed (kW) 151 104 75Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 405. EUR 29978 EN; JRC118627; doi:10.2760/243911
- 75 kW
Electric power of the advanced-design homogenizer
Vergleichswert · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
Homogenisation pressure (bar) 200 135 97 Electric power needed (kW) 151 104 75Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 405. EUR 29978 EN; JRC118627; doi:10.2760/243911
- 25.000 L/h
Homogenizer capacity of the documented comparison
Vergleichswert · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
Conditions: homogeniser capacity 25 000 l/h; desired homogenisation effect 75 % NIZOBest Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 405. EUR 29978 EN; JRC118627; doi:10.2760/243911
- 24 h
Maximum interval between two cleanings of milk equipment
Regulatorisch · Fest
Verifiziertes ZitatWörtliches Zitat anzeigen
all equipment is thoroughly cleaned at least once each day usedGrade "A" Pasteurized Milk Ordinance, 2023 Revision (öffnet in neuem Tab). U.S. Department of Health and Human Services, Public Health Service, Food and Drug Administration, 2023. S. 98. PMO 2023 Revision
- 0,374294 h
Minimum duration of a cleaning-in-place programme (output cip_time_min of the cleaning model, with its Monte Carlo interval)
Stoffwert · Dreiecksverteilt 0,242184, 0,374294, 0,536161 h
BerechnetOutput `cip_time_min` of the cleaning model: 22.46 min [14.53, 32.17].
- 2.000 h
Operating hours between exchanges of worn homogenizing valve parts and plunger seals
Szenario · Gleichverteilt 1.000 bis 4.000 h
Deklarierte AnnahmeDeclared assumption; wear depends on pressure, product and seal lubrication.
- 2 h
Duration of the exchange of valve parts and seals
Szenario · Gleichverteilt 1 bis 4 h
Deklarierte Annahme
8Vergleichswerte
| Vergleichswert | Obergrenze | Wert | Herkunft |
|---|---|---|---|
Conventional homogenizer, 200 bar, 151 kW at 25 000 L/h (BAT reference document; electricity per kg computed with the milk density)Wörtliches Zitat anzeigenHomogenisation pressure (bar) 200 135 97 Electric power needed (kW) 151 104 75Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 405. EUR 29978 EN; JRC118627; doi:10.2760/243911 | Typisch | 151 kW | Verifiziertes Zitat |
Advanced-design homogenizer, 97 bar, 75 kW at 25 000 L/h for the same homogenization effect (per-kilogram value: output energy_bat)Wörtliches Zitat anzeigenHomogenisation pressure (bar) 200 135 97 Electric power needed (kW) 151 104 75Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 405. EUR 29978 EN; JRC118627; doi:10.2760/243911 | Beste verfügbare Technik | 75 kW | Verifiziertes Zitat |
Documented statement that less than 1 % of the energy is used for the homogenization itself (compare with the output surface_energy_efficiency)Wörtliches Zitat anzeigenLess than 1% of the energy is utilised for homogenization.Dairy Processing Handbook, chapter 7.3: Homogenizers (öffnet in neuem Tab). Tetra Pak Processing Systems AB (online edition, openly readable), 2026. Tetra Pak Dairy Processing Handbook, online edition, chapter 7.3 (read 2026-11-15) | — | 1 % | Verifiziertes Zitat |
Documented increase of the fat/plasma interfacial area by homogenization, lower end of 'four- to six-fold' (compare with the output area_increase_ratio)Wörtliches Zitat anzeigenThis is accompanied by a four- to six-fold increase in the fat/plasma interfacial surface area.Dairy Processing Handbook, chapter 7.3: Homogenizers (öffnet in neuem Tab). Tetra Pak Processing Systems AB (online edition, openly readable), 2026. Tetra Pak Dairy Processing Handbook, online edition, chapter 7.3 (read 2026-11-15) | — | 4 | Verifiziertes Zitat |
Documented temperature rise: 1 °C per 4 MPa of pressure drop (reproduced by the output temperature_rise_per_MPa)Wörtliches Zitat anzeigenevery 4 MPa (40 bar) in pressure drop over the device gives a temperature rise of 1 °CDairy Processing Handbook, chapter 7.3: Homogenizers (öffnet in neuem Tab). Tetra Pak Processing Systems AB (online edition, openly readable), 2026. Tetra Pak Dairy Processing Handbook, online edition, chapter 7.3 (read 2026-11-15) | — | 4 MPa | Verifiziertes Zitat |
Documented liquid velocity in the homogenizing gap, lower end of 100–400 m/s (compare with the output gap_velocity)Wörtliches Zitat anzeigenThe velocity of the liquid is normally 100 – 400 m/s in the narrow annular gap.Dairy Processing Handbook, chapter 7.3: Homogenizers (öffnet in neuem Tab). Tetra Pak Processing Systems AB (online edition, openly readable), 2026. Tetra Pak Dairy Processing Handbook, online edition, chapter 7.3 (read 2026-11-15) | — | 100 m/s | Verifiziertes Zitat |
9Unvermeidbare Stillstände
- Cleaning at least once per day of useVerifiziertes Zitat
Hygiene regulation: milk equipment must be cleaned at least once each day used. The homogenizer is cleaned in place with the pasteurizer circuit; minimum programme of the cleaning model (a lower bound for the pump block, assumption a5).
Wörtliches Zitat anzeigen
all equipment is thoroughly cleaned at least once each day usedGrade "A" Pasteurized Milk Ordinance, 2023 Revision (öffnet in neuem Tab). U.S. Department of Health and Human Services, Public Health Service, Food and Drug Administration, 2023. S. 98. PMO 2023 Revision
- Exchange of worn valve parts and plunger sealsVerifiziertes Zitat
The homogenizing valve and the plunger seals wear under the pressure load and must be exchanged; interval and duration are declared scenarios. The BAT reference document notes that a lower pressure makes these intervals longer.
Wörtliches Zitat anzeigen
A lower pressure also means less load on the homogeniser, so maintenance and worn parts’ replacement intervals will be less frequentBest Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 405. EUR 29978 EN; JRC118627; doi:10.2760/243911
10Annahmen
- Creaming of homogenized milk follows Stokes' law for independent globules (homogenized globules do not cluster by cold agglutination); a globule class rising a distance s enriches the top layer by s/h_top and depletes the bottom by s/(H - h_top) (valid while s is much smaller than the top layer).
- The homogenized size distribution is log-normal by volume, with the documented median at 20 MPa and the width fixed by the documented share of globules larger than 1 µm; its median scales as p^-b with an unchanged width.
- The serum viscosity at the storage temperature is the handbook reference value scaled with the viscosity of water (constant relative viscosity, IAPWS through CoolProp).
- The minimum pressure belongs to the reference two-stage valve of the documented size data; other valve geometries reach the same size at other pressures, so the energy ceilings below the theoretical one are documented values, not computed ones. Homogenizing pressure under control is normally distributed; milk homogenized below the minimum pressure fails the creaming test and is reworked.
- Availability: the daily cleaning of milk equipment at the minimum duration of the cleaning model (valid for recirculated pipe and plate circuits; the pump block and valve are outside that validity, so the linked duration is a lower bound) and the wear-forced exchange of valve parts and seals at declared intervals. The homogenizer is a positive-displacement pump: its rate is fixed by the pump, P = 1, and no product is lost in it (yield 1; the start-up mixing zones belong to the pasteurization line).
11Gültigkeitsbereich
- Whole or semi-skimmed bovine milk homogenized warm (55–80 °C) in a two-stage valve homogenizer and stored at or below 7 °C.
- Not for high-fat cream, ice-cream mix or ultra-high-pressure homogenization (above about 50 MPa), whose size laws differ.
12Sensitivität
- Maximum interval between two cleanings of milk equipmentElastizität +0,016Spearman-ρ —
- Minimum duration of a cleaning-in-place programme (output cip_time_min of the cleaning model, with its Monte Carlo interval)Elastizität -0,016Spearman-ρ -0,82
- Margin of the pressure set point above the minimum pressure, in standard deviationsElastizität +0,014Spearman-ρ +0,48
- Operating hours between exchanges of worn homogenizing valve parts and plunger sealsElastizität +0,001Spearman-ρ +0,15
- Duration of the exchange of valve parts and sealsElastizität -0,001Spearman-ρ -0,13
- Größe steigt mit dem Parameter
- Größe sinkt mit dem Parameter
13Validierungsprüfungen
- Dimensionsanalyse27 outputs converted to their declared unitsBestanden
- Jeder zitierte Wert an seiner Quelle verifiziert32 verified, 0 failedBestanden
- Kein dokumentierter Wert übertrifft die theoretische GrenzeBestanden
- Obergrenzen in physikalischer ReihenfolgeBestanden
- Anteile zwischen 0 und 1Bestanden
14Verlustursachen in dieser Operation
- Homogenizer mechanical/component failure (plunger, flange, monoblock, flowmeter)Anlagenausfall (Störungen)1,1 % [0,2–3,4 %]D28 Studien
- Homogenizer pressure instabilityAnlagenausfall (Störungen)1,1 % [0,2–3,2 %]D28 Studien
15Literatur
- Dairy Processing Handbook, chapter 7.3: Homogenizers (öffnet in neuem Tab). Tetra Pak Processing Systems AB (online edition, openly readable), 2026. Tetra Pak Dairy Processing Handbook, online edition, chapter 7.3 (read 2026-11-15)
- Dairy Processing Handbook, chapter 2: The chemistry of milk (öffnet in neuem Tab). Tetra Pak Processing Systems AB (online edition, openly readable), 2026. Tetra Pak Dairy Processing Handbook, online edition, chapter 2 (read 2026-11-15)
- Dairy Processing Handbook, chapter 7.2: Centrifugal separators and milk standardization (öffnet in neuem Tab). Tetra Pak Processing Systems AB (online edition, openly readable), 2026. Tetra Pak Dairy Processing Handbook, online edition, chapter 7.2 (read 2026-11-15)
- Effect of Homogenization Pressure on Plasmin Activity and Mechanical Stress-Induced Fat Aggregation of Commercially Sterilized Ultra High Temperature Milk during Storage (Kim, Yun, Ahn, Kim, Imm; Food Science of Animal Resources 40(5): 734-745) (öffnet in neuem Tab). Korean Society for Food Science of Animal Resources (open access, CC BY-NC 3.0); full text served by Europe PMC, 2020. doi:10.5851/kosfa.2020.e48; PMC7492180
- Oil-water interfacial behaviour of different caseins and stability of emulsions: Effect of micelle content and caseins concentrations (Yan, Li, Wang, Li, Zhang, Yan et al.; Food Chemistry: X 23: 101784) (öffnet in neuem Tab). Elsevier (open access, CC BY-NC-ND 4.0); full text served by Europe PMC, 2024. doi:10.1016/j.fochx.2024.101784; PMC11403417
- Organization of lipids in milks, infant milk formulas and various dairy products: role of technological processes and potential impacts (Lopez, Cauty, Guyomarc'h; Dairy Science & Technology 95: 863-893) (öffnet in neuem Tab). Springer / INRA (open access); full text served by Europe PMC, 2015. doi:10.1007/s13594-015-0263-0; PMC4641158
- Grade "A" Pasteurized Milk Ordinance, 2023 Revision (öffnet in neuem Tab). U.S. Department of Health and Human Services, Public Health Service, Food and Drug Administration, 2023. S. 57. PMO 2023 Revision
- Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 405. EUR 29978 EN; JRC118627; doi:10.2760/243911
- doi:10.1002/aic.690010303 — Maximum stable drop size in turbulent dispersion (Hinze).
- doi:10.1098/rspa.1991.0075 — Local structure of turbulence (Kolmogorov, English translation of the 1941 paper).
- doi:10.5851/kosfa.2020.e48 — Fat globule size distributions of milk homogenized at 20, 25 and 30 MPa.
- doi:10.1016/j.fochx.2024.101784 — Interfacial tension of milk fat against water and casein dispersions.
- doi:10.1021/ie4033999 — Thermophysical property library (viscosity of water).

