Falla de componentes de tubería y válvulas del esterilizador
En resumen
Aparece en cerca de 6 de cada 100 líneas estudiadas.
Cuando aparece, se lleva en promedio cerca del 60 % del tiempo perdido de la línea. La reportan 7 de los 34 estudios que podían observarla (evidencia buena).
Qué pasa
Los componentes mecánicos del esterilizador, como tuberías, bridas, codos, revestimientos, tuercas y actuadores neumáticos, sufren desgaste, corrosión, fatiga o aflojamiento por los ciclos repetidos de presión y temperatura, lo que provoca fugas, agarrotamiento o pérdida de accionamiento. Esto obliga a detener el proceso de esterilización hasta que el personal de mantenimiento repare o reemplace la pieza dañada.
Qué se hace
Implementar un programa de mantenimiento preventivo y predictivo que cubra tuberías, bridas, codos, revestimientos, tuercas y actuadores, incluyendo inspección periódica, verificación de torque, programas de reemplazo de empaques y revestimientos, y monitoreo de corrosión. Mantener repuestos críticos disponibles para reducir el tiempo de reparación cuando ocurra una falla.
Orientación práctica basada en conocimiento de ingeniería; no es una estimación estadística.
1Probabilidad y evidencia
- Probabilidad de presencia
- 6.2 % [1.9–13.9 %]
- Proporción esperada del tiempo perdido
- 3.7 % [1.1–8.3 %]
- Proporción del tiempo perdido cuando está presente
- 60 % [49–70 %]
- Estudios / unidades
- 34 / 37
- Grado de evidencia
- B
Grado B: de 5 a 9 estudios, o un ancho de intervalo entre 0,20 y 0,35.
2Probabilidad por segmento
- Productos lácteos6.2 % [1.0–17.7 %]5 estudios
- Refrescos, agua embotellada y jugos6.5 % [1.0–20.2 %]2 estudios
- Cerveza, vino y destilados9.5 % [1.7–28.2 %]1 estudio
- Panadería y pastas7.1 % [1.0–21.8 %]0 estudios
- Carne, aves y pescado6.8 % [1.0–20.8 %]1 estudio
- Procesamiento de frutas y vegetales6.4 % [1.0–18.6 %]2 estudios
- Molienda de granos y oleaginosas29 % [8–60 %]6 estudios
- Azúcar y confitería6.3 % [1.1–17.9 %]3 estudios
- Snacks, café, té y otros alimentos6.0 % [0.9–17.2 %]3 estudios
- Alimento animal y para mascotas6.2 % [1.0–18.1 %]4 estudios
- Manufactura de alimentos (sin especificar o mixta)5.8 % [1.0–16.4 %]7 estudios
3Mecanismo, firma en SCADA y contramedida
Mecanismo
Guía de ingenieríaLos componentes mecánicos del esterilizador, como tuberías, bridas, codos, revestimientos, tuercas y actuadores neumáticos, sufren desgaste, corrosión, fatiga o aflojamiento por los ciclos repetidos de presión y temperatura, lo que provoca fugas, agarrotamiento o pérdida de accionamiento. Esto obliga a detener el proceso de esterilización hasta que el personal de mantenimiento repare o reemplace la pieza dañada.
Cómo se ve en los datos de SCADA
Guía de ingenieríaLos registros de SCADA/MES muestran al esterilizador entrando en estado de paro no planificado o falla con alarmas asociadas a desviación de presión, discrepancia en la retroalimentación de posición del actuador, o códigos de falla de válvulas y tuberías, frecuentemente repetidos en el mismo subsistema. Estos eventos aparecen como paradas discretas atribuidas a componentes mecánicos en lugar de a parámetros de proceso, y suelen ir seguidos de un tiempo prolongado de intervención de mantenimiento.
Contramedida
Guía de ingenieríaImplementar un programa de mantenimiento preventivo y predictivo que cubra tuberías, bridas, codos, revestimientos, tuercas y actuadores, incluyendo inspección periódica, verificación de torque, programas de reemplazo de empaques y revestimientos, y monitoreo de corrosión. Mantener repuestos críticos disponibles para reducir el tiempo de reparación cuando ocurra una falla.
4Fuentes
- Analisa Perawatan Mesin Sterilizer Menggunakan Metode Overall Equipment Effectivenees (OEE) Pada PT. Djaja Putra Indonesia Kabupaten Asahan (2020)Abrir fuenteProporción del tiempo perdido: 61.5 % · según el reporte: “Equipment Failures”
Ver cita textual
Faktor terbesar yang mempengaruhi efektifitas mesin Sterilizer dan menjadi prioritas untuk dieleminasi adalah faktor Equipment Failures sebesar 61,54% dan faktor Idling minor Stoppages sebesar 25,15%.
- Study on Preventive Maintenance Strategies of Filling Equipment Based on Reliability-Cantered Maintenance (2021)Abrir fuenteTiempo perdido: 500 min · según el reporte: “SM”
Ver cita textual
Total 2540 485 500 560 450 265 225 240 220 5485 224940 2.44%
- Study on Preventive Maintenance Strategies of Filling Equipment Based on Reliability-Cantered Maintenance (2021)Abrir fuenteNúmero de eventos: 24.0 events · según el reporte: “SM”
Ver cita textual
Total 61 21 24 22 17 7 11 10 8 181
- ANALISA PERHITUNGAN OVERALL EQUIPMENT EFFECTIVENESS (OEE) PADA PROSES AWAL PENGOLAHAN KELAPA SAWIT DI PT. PERKEBUNAN NUSANTARA IV GUNUNG BAYU (2019)Abrir fuenteProporción del tiempo perdido: 0 % · según el reporte: “Rework Loss”
Ver cita textual
Idling And Minor Stoppages by 0% and Rework Loss by 0%
- ANALISA PERHITUNGAN OVERALL EQUIPMENT EFFECTIVENESS (OEE) PADA PROSES AWAL PENGOLAHAN KELAPA SAWIT DI PT. PERKEBUNAN NUSANTARA IV GUNUNG BAYU (2019)Abrir fuenteProporción del tiempo perdido: 4.69 % · según el reporte: “Yield / Scrap Losses”
Ver cita textual
Reduced Speed Losses by 67.54%, then Breakdown Lossses by 18.48%, Set Up and Adjustment Losses by 9.35%, Yield / Scrap Losses by 4.69 %, Idling And Minor Stoppages by 0% and Rework Loss by 0%
- ANALISA PERHITUNGAN OVERALL EQUIPMENT EFFECTIVENESS (OEE) PADA PROSES AWAL PENGOLAHAN KELAPA SAWIT DI PT. PERKEBUNAN NUSANTARA IV GUNUNG BAYU (2019)Abrir fuenteProporción del tiempo perdido: 9.35 % · según el reporte: “Set Up and Adjustment Losses”
Ver cita textual
Reduced Speed Losses by 67.54%, then Breakdown Lossses by 18.48%, Set Up and Adjustment Losses by 9.35%, Yield / Scrap Losses by 4.69 %, Idling And Minor Stoppages by 0% and Rework Loss by 0%
- ANALISA PERHITUNGAN OVERALL EQUIPMENT EFFECTIVENESS (OEE) PADA PROSES AWAL PENGOLAHAN KELAPA SAWIT DI PT. PERKEBUNAN NUSANTARA IV GUNUNG BAYU (2019)Abrir fuenteProporción del tiempo perdido: 18.5 % · según el reporte: “Breakdown Losses”
Ver cita textual
Reduced Speed Losses by 67.54%, then Breakdown Lossses by 18.48%, Set Up and Adjustment Losses by 9.35%, Yield / Scrap Losses by 4.69 %, Idling And Minor Stoppages by 0% and Rework Loss by 0%
- ANALISA PERHITUNGAN OVERALL EQUIPMENT EFFECTIVENESS (OEE) PADA PROSES AWAL PENGOLAHAN KELAPA SAWIT DI PT. PERKEBUNAN NUSANTARA IV GUNUNG BAYU (2019)Abrir fuenteProporción del tiempo perdido: 67.5 % · según el reporte: “Reduced Speed Losses”
Ver cita textual
Reduced Speed Losses by 67.54%, then Breakdown Lossses by 18.48%, Set Up and Adjustment Losses by 9.35%, Yield / Scrap Losses by 4.69 %, Idling And Minor Stoppages by 0% and Rework Loss by 0%
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Abrir fuenteNúmero de eventos: 4.00 events · según el reporte: “Flange Pipe”
Ver cita textual
Flange Pipe 4
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Abrir fuenteNúmero de eventos: 2.00 events · según el reporte: “Ball Valve”
Ver cita textual
Ball Valve 2
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Abrir fuenteNúmero de eventos: 2.00 events · según el reporte: “Actuator”
Ver cita textual
Actuator 2
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Abrir fuenteNúmero de eventos: 2.00 events · según el reporte: “Valve Exhaust”
Ver cita textual
Valve Exhaust 2
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Abrir fuenteNúmero de eventos: 1.00 events · según el reporte: “Valve Condensat”
Ver cita textual
Valve Condensat 1
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Abrir fuenteNúmero de eventos: 1.00 events · según el reporte: “Streiner Valve”
Ver cita textual
Streiner Valve 1
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Abrir fuenteTiempo entre eventos: 510 hours · según el reporte: “Elbow”
Ver cita textual
Elbow 4 510,1
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Abrir fuenteTiempo entre eventos: 510 hours · según el reporte: “Flange Pipe”
Ver cita textual
Flange Pipe 4 510,1
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Abrir fuenteTiempo entre eventos: 680 hours · según el reporte: “Pipe”
Ver cita textual
Pipe 3 680,13
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Abrir fuenteTiempo entre eventos: 1,020 hours · según el reporte: “Ball Valve”
Ver cita textual
Ball Valve 2 1020,2
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Abrir fuenteTiempo entre eventos: 1,020 hours · según el reporte: “Liner”
Ver cita textual
Liner 2 1020,2
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Abrir fuenteTiempo entre eventos: 1,020 hours · según el reporte: “Actuator”
Ver cita textual
Actuator 2 1020,2
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Abrir fuenteTiempo entre eventos: 1,020 hours · según el reporte: “Valve Exhaust”
Ver cita textual
Valve Exhaust 2 1020,2
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Abrir fuenteTiempo entre eventos: 2,040 hours · según el reporte: “Valve Condensat”
Ver cita textual
Valve Condensat 1 2040
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Abrir fuenteTiempo entre eventos: 2,040 hours · según el reporte: “Streiner Valve”
Ver cita textual
Streiner Valve 1 2040
- Analisis Kelayakan Mesin Sterilizer Dengan Metode Overall Equipment Effectiveness (OEE) Pada PT. Hari Sawit Jaya Labuhanbatu, Sumatera Utara (2023)Abrir fuenteTiempo perdido: 19,320 min · según el reporte: “planned downtime”
Ver cita textual
selain itu terdapat total data dari planned downtime dari bulan Januari-Agustus 2023 adalah 19.320 menit.
- Analisis Kelayakan Mesin Sterilizer Dengan Metode Overall Equipment Effectiveness (OEE) Pada PT. Hari Sawit Jaya Labuhanbatu, Sumatera Utara (2023)Abrir fuenteTiempo perdido: 22,786 min · según el reporte: “downtime mesin”
Ver cita textual
Data dari Januari hingga Agustus 2023 mencapai 22.786 menit, yang berdampak negatif pada proses produksi.
- Penerapan Metode Total Productive Maintenance Dan Overall Equipment Effectiveness Pada Mesin Sterilizer Di PT. Tri Cahaya Sawit (2025)Abrir fuenteTiempo perdido: 47.0 h/month · según el reporte: “downtime”
Ver cita textual
tercatat bahwa mesin sterilizer mengalami downtime rata-rata 47 jam per bulan, dengan jumlah gangguan teknis mencapai 6–8 kali per bulan.
- Analisis Losses Minyak Sawit pada Proses Pengolahan Pabrik Kelapa Sawit PT Perkebunan Nusantara IV Regional IV Unit Usaha PKS Bunut (2026)Abrir fuenteTasa de defectos: 0.0400 % · según el reporte: “USF (unstripped fruit)”
Ver cita textual
Nilai rata-rata losses USF selama periode pengamatan tercatat sebesar 0,04%, sedangkan batas norma industri berada pada nilai 0,09%.
- Analisis Losses Minyak Sawit pada Proses Pengolahan Pabrik Kelapa Sawit PT Perkebunan Nusantara IV Regional IV Unit Usaha PKS Bunut (2026)Abrir fuenteTasa de defectos: 0.370 % · según el reporte: “Janjangan kosong”
Ver cita textual
Evaluasi terhadap janjang kosong memperlihatkan bahwa rata-rata losses berada pada nilai 0,37% dengan batas norma maksimum sebesar 0,44%.
- Analisis Losses Minyak Sawit pada Proses Pengolahan Pabrik Kelapa Sawit PT Perkebunan Nusantara IV Regional IV Unit Usaha PKS Bunut (2026)Abrir fuenteTasa de defectos: 0.0900 % · según el reporte: “Nut”
Ver cita textual
Nut 0,09 0,10 Mendekati batas

