foratvise
Comenzar
Estudio incluido

Set Up Time Reduction Using Single Minute Exchange of Dies (SMED) and 5S: A Case Study

Abrir fuente

1Ficha bibliográfica

Autores
Johan Krisnanto Runtuk
Año
2021
Publicación
JIE Scientific Journal on Research and Application of Industrial System
País
—
Segmento
Manufactura de alimentos (sin especificar o mixta)
Familia de procesos
Línea de llenado y envasado
Tipo de estudio
Intervención antes/después
Alcance de la extracción
Texto completo
Tamaño
1 plantas · 1 líneas · 1 máquinas
Periodo de observación
92 días
Recolección de datos
manual_logs
Intervención
Ver el contexto tal como lo describe el estudio
As one of the foods and beverages industry, PT. MNO also focuses on reducing waste in the production process, especially in the filling department.

2Riesgo de sesgo

Puntuado con la rúbrica del protocolo: 2 preocupación baja, 1 algunas preocupaciones, 0 preocupación alta.
Puntuación total 11Riesgo moderado
ÍtemPuntuación
Is the observed line, machine or plant described well enough to classify its segment, process and equipment?Product or sector is given but the equipment or process is only partly described.1 / 2
Is the observation period long enough and reported?Period reported and at least 30 days of production (or at least 100 recorded events).2 / 2
How were loss data collected?Manual logs or maintenance records with unknown completeness.1 / 2
Are OEE, loading time and the loss categories defined explicitly?Formulae or definitions are given for the reported metrics, including what counts as planned time.2 / 2
Does the loss breakdown account for the total loss it claims to explain?Only the top causes are reported and the unexplained remainder can be computed.1 / 2
Is there evidence of selective reporting of favourable results?Observational study, or intervention study that reports baseline and post-intervention data with the same method.2 / 2
Are the reported numbers internally consistent?Small inconsistencies (2 to 10 percentage points) or values that cannot be cross-checked.1 / 2
Could conflicts of interest or the source of the data bias the result?Authors are employees of the plant or of an equipment/software vendor; no declaration.1 / 2

3Datos extraídos

Cada dato con su clasificación y la cita textual que lo establece.
Causa reportadaCategoría de pérdidaMétricaValorExtracción
setup time or line preparation timefilling machine
Ver cita textual (Section 1, Introduction)
The most significant contribution of planned stoppages is 48% comes from setup time or line preparation time.
Setups y ajustesProporción del tiempo perdido48.0 %Un solo extractor
cleaning inspection and lubrication processfilling machine
Ver cita textual (Section 1, Introduction)
The next is 34% of cleaning inspection and lubrication process, 19% of operational stoppages, 3% of meals or break, 2% of change over time, and the last 1% of planned maintenance.
Paro planificado (mantenimiento programado, descansos, sin demanda)Proporción del tiempo perdido34.0 %Un solo extractor
operational stoppagesfilling machine
Ver cita textual (Section 1, Introduction)
The next is 34% of cleaning inspection and lubrication process, 19% of operational stoppages, 3% of meals or break, 2% of change over time, and the last 1% of planned maintenance.
No clasificable a partir del reporteProporción del tiempo perdido19.0 %Un solo extractor
meals or breakfilling machine
Ver cita textual (Section 1, Introduction)
The next is 34% of cleaning inspection and lubrication process, 19% of operational stoppages, 3% of meals or break, 2% of change over time, and the last 1% of planned maintenance.
Paro planificado (mantenimiento programado, descansos, sin demanda)Proporción del tiempo perdido3.00 %Un solo extractor
change over timefilling machine
Ver cita textual (Section 1, Introduction)
The next is 34% of cleaning inspection and lubrication process, 19% of operational stoppages, 3% of meals or break, 2% of change over time, and the last 1% of planned maintenance.
Setups y ajustesProporción del tiempo perdido2.00 %Un solo extractor
planned maintenancefilling machine
Ver cita textual (Section 1, Introduction)
The next is 34% of cleaning inspection and lubrication process, 19% of operational stoppages, 3% of meals or break, 2% of change over time, and the last 1% of planned maintenance.
Paro planificado (mantenimiento programado, descansos, sin demanda)Proporción del tiempo perdido1.00 %Un solo extractor
planned stoppagesfilling machine
Ver cita textual (Section 1, Introduction)
Based on the whole company manufacturing process, the highest number of waiting waste occurs in filling machines, especially for the planned stoppages with 67% compared with the 33% for the unplanned stoppages.
No clasificable a partir del reporteProporción del tiempo perdido67.0 %Un solo extractor
unplanned stoppagesfilling machine
Ver cita textual (Section 1, Introduction)
Based on the whole company manufacturing process, the highest number of waiting waste occurs in filling machines, especially for the planned stoppages with 67% compared with the 33% for the unplanned stoppages.
No clasificable a partir del reporteProporción del tiempo perdido33.0 %Un solo extractor
—filling machine
Ver cita textual (Section 3.1, Table 2)
The total time needed to conduct the setup activities in the filling machine is 34 minutes, with eight different activities.
Setups y ajustesTiempo perdido34.0 minutesUn solo extractor
—filling machine
Ver cita textual (Section 3.2)
The availability rates from April and June 2016 are 86% and 89%.
noneDisponibilidad86.0 %Un solo extractor
—filling machine
Ver cita textual (Section 3.2)
The performance rate from May and June 2016 is 88% and 88%.
noneRendimiento88.0 %Un solo extractor
—filling machine
Ver cita textual (Section 3.2)
The quality rate for the entire month from May and June 2016 is 100%.
noneCalidad100 %Un solo extractor
—filling machine
Ver cita textual (Section 3.2)
Then, the OEE rates are 76% and 78% from May until June 2016.
noneOEE76.0 %Un solo extractor
—filling machine
Ver cita textual (Section 3.1, Table 4)
Table 4 shows that the setup activities, which means the activities done when the machine stops, are reduced from 13 minutes to 10 minutes.
Setups y ajustesTiempo perdido10.0 minutesUn solo extractor
—filling machine
Ver cita textual (Section 3.2)
The availability rates from April and June 2016 are 86% and 89%.
noneDisponibilidad89.0 %Un solo extractor
—filling machine
Ver cita textual (Section 3.2)
The performance rate from May and June 2016 is 88% and 88%.
noneRendimiento88.0 %Un solo extractor
—filling machine
Ver cita textual (Section 3.2)
The quality rate for the entire month from May and June 2016 is 100%.
noneCalidad100 %Un solo extractor
—filling machine
Ver cita textual (Section 3.2)
Then, the OEE rates are 76% and 78% from May until June 2016.
noneOEE78.0 %Un solo extractor
Setup timefilling machine
Ver cita textual (Page 5, Section 3.1, SMED and 5S)
Before the improvement of Single Minute Exchange of Dies (SMED), the actual setup activities are eight activities in total with 34 minutes to finish the setup activities
Setups y ajustesTiempo perdido34.0 minUn solo extractor
Checking Metal Detectormetal detector
Ver cita textual (Table 2, Page 6)
Record Counter Metal Detector 0:00:00 0:01:00 0:01:00; Verified positive sample metal detector 0:01:00 0:02:00 0:01:00
Setups y ajustesTiempo perdido2.00 minUn solo extractor
Cleaning Environmentfilling machine
Ver cita textual (Table 2, Page 6, Activity group B)
Take Cleaning Tools 0:02:00 0:04:00 0:02:00; Cleaning floor below the machine 0:04:00 0:07:00 0:03:00; Tidy Up Cleaning Tools 0:07:00 0:09:00 0:02:00
Setups y ajustesTiempo perdido7.00 minUn solo extractor
Cut Open Reworkfilling machine
Ver cita textual (Table 2, Page 6, Activity group G)
Cut Open Rework 0:28:00 0:31:00 0:03:00
Setups y ajustesTiempo perdido3.00 minUn solo extractor
SHO Updateshift handover documentation
Ver cita textual (Table 2, Page 6, Activity group H)
SHO Update 0:31:00 0:34:00 0:03:00
Setups y ajustesTiempo perdido3.00 minUn solo extractor

Unidades de observación

  • Filling Machine · Llenado · Línea base
  • Filling Machine · Llenado · Después de la intervención