En resumen
Aparece en cerca de 4 de cada 100 líneas estudiadas.
Cuando aparece, se lleva en promedio cerca del 56 % del tiempo perdido de la línea. La reportan 13 de los 120 estudios que podían observarla (evidencia sólida).
Qué pasa
Se pierde tiempo entre la última unidad buena de un lote de llenado y la primera unidad buena del siguiente porque la llenadora debe detenerse para cambiar piezas en contacto con el producto (boquillas, elementos de dosificación, guías de formato), reconfigurar parámetros de dosificación o sellado, y ajustar finamente el equipo hasta que la salida se estabiliza. Incluye el cambio mecánico de piezas, la introducción de parámetros y los ajustes de prueba antes de alcanzar la precisión de llenado y calidad de sellado objetivo.
Qué se hace
Aplicar métodos estructurados de cambio rápido (SMED) para separar las actividades de ajuste internas y externas, preparar previamente herramientas y recetas, y emplear instrucciones de trabajo estandarizadas con conjuntos de parámetros predefinidos para reducir el ajuste por prueba y error. Automatizar la recuperación de parámetros y emplear acoples de cambio rápido sin herramientas acorta aún más el intervalo no productivo.
Orientación práctica basada en conocimiento de ingeniería; no es una estimación estadística.
1Probabilidad y evidencia
- Probabilidad de presencia
- 3.6 % [1.5–7.1 %]
- Proporción esperada del tiempo perdido
- 2.0 % [0.8–4.0 %]
- Proporción del tiempo perdido cuando está presente
- 56 % [45–65 %]
- Estudios / unidades
- 120 / 162
- Grado de evidencia
- A
Grado A: 10 o más estudios y 10 o más líneas distintas, con un intervalo de credibilidad del 95 % de ancho menor a 0,20.
2Probabilidad por segmento
- Productos lácteos5.4 % [1.3–13.3 %]18 estudios
- Refrescos, agua embotellada y jugos3.1 % [1.0–6.6 %]44 estudios
- Cerveza, vino y destilados5.1 % [1.3–12.1 %]16 estudios
- Panadería y pastas4.4 % [0.7–13.4 %]0 estudios
- Carne, aves y pescado4.8 % [1.0–13.2 %]6 estudios
- Procesamiento de frutas y vegetales3.9 % [0.7–10.9 %]4 estudios
- Molienda de granos y oleaginosas3.7 % [0.7–10.7 %]6 estudios
- Azúcar y confitería4.0 % [0.7–11.6 %]3 estudios
- Snacks, café, té y otros alimentos6.6 % [1.5–18.0 %]6 estudios
- Alimento animal y para mascotas3.9 % [0.7–11.2 %]4 estudios
- Manufactura de alimentos (sin especificar o mixta)6.1 % [1.5–15.6 %]13 estudios
3Mecanismo, firma en SCADA y contramedida
Mecanismo
Guía de ingenieríaSe pierde tiempo entre la última unidad buena de un lote de llenado y la primera unidad buena del siguiente porque la llenadora debe detenerse para cambiar piezas en contacto con el producto (boquillas, elementos de dosificación, guías de formato), reconfigurar parámetros de dosificación o sellado, y ajustar finamente el equipo hasta que la salida se estabiliza. Incluye el cambio mecánico de piezas, la introducción de parámetros y los ajustes de prueba antes de alcanzar la precisión de llenado y calidad de sellado objetivo.
Cómo se ve en los datos de SCADA
Guía de ingenieríaEl SCADA/MES muestra una duración de estado de máquina prolongada registrada como cambio de formato o ajuste, con la llenadora en estado de no producción mientras los equipos aguas arriba y aguas abajo pueden sufrir inanición o bloqueo; los contadores de unidades buenas permanecen planos durante este intervalo. Pueden aparecer ciclos cortos repetidos de alternancia entre estado de ajuste y marcha mientras los operadores realizan ajustes finos iterativos antes de confirmar la producción estable.
Contramedida
Guía de ingenieríaAplicar métodos estructurados de cambio rápido (SMED) para separar las actividades de ajuste internas y externas, preparar previamente herramientas y recetas, y emplear instrucciones de trabajo estandarizadas con conjuntos de parámetros predefinidos para reducir el ajuste por prueba y error. Automatizar la recuperación de parámetros y emplear acoples de cambio rápido sin herramientas acorta aún más el intervalo no productivo.
4Fuentes
- Tiempo perdido: 38.0 min · según el reporte: “Mudar e transportar peças de formato”
Ver cita textual
7, 8, 11, 12 Mudar e transportar peças de formato 38 20
- Tiempo perdido: 14.0 min · según el reporte: “Ajustes”
Ver cita textual
16 Ajustes 14 4
- Tiempo perdido: 5.00 min · según el reporte: “Testar enchimento”
Ver cita textual
21 Testar enchimento 5 0
- Tiempo perdido: 1.00 min · según el reporte: “Trazer a mangueira para junto da enchedora”
Ver cita textual
10 Trazer a mangueira para junto da enchedora 1 0
- Duración media del evento: 103 min · según el reporte: “Mudança de tara”
Ver cita textual
Mudança de tara 102,5 min 42 min 60,5 min 1,07%
- Duración media del evento: 118 min · según el reporte: “Mudança de cápsula”
Ver cita textual
Mudança de cápsula 118,4 min 55 min 63,4 min
- Duración media del evento: 152 min · según el reporte: “Mudança de tara e cápsula”
Ver cita textual
Mudança de tara e cápsula 151,8 min 84 min 67,8 min
- Duración media del evento: 115 min · según el reporte: “Mudança de tara (trabalho interno)”
Ver cita textual
A média da duração de trabalho interno das mudanças de tara observadas é de 115 minutos.
- Duración media del evento: 100 min · según el reporte: “Mudança de cápsula (trabalho interno)”
Ver cita textual
A média da duração de trabalho interno das mudanças de cápsula observadas é de 100 minutos.
- Tiempo perdido: 20.0 min · según el reporte: “Mudar e transportar peças de formato”
Ver cita textual
7, 8, 11, 12 Mudar e transportar peças de formato 38 20
- Tiempo perdido: 4.00 min · según el reporte: “Ajustes”
Ver cita textual
16 Ajustes 14 4
- Tiempo perdido: 0 min · según el reporte: “Testar enchimento”
Ver cita textual
21 Testar enchimento 5 0
- Tiempo perdido: 0 min · según el reporte: “Trazer a mangueira para junto da enchedora”
Ver cita textual
10 Trazer a mangueira para junto da enchedora 1 0
- Duración media del evento: 42.0 min · según el reporte: “Mudança de tara”
Ver cita textual
Mudança de tara 102,5 min 42 min 60,5 min 1,07%
- Duración media del evento: 55.0 min · según el reporte: “Mudança de cápsula”
Ver cita textual
Mudança de cápsula 118,4 min 55 min 63,4 min
- Duración media del evento: 84.0 min · según el reporte: “Mudança de tara e cápsula”
Ver cita textual
Mudança de tara e cápsula 151,8 min 84 min 67,8 min
- Duración media del evento: 30.0 min · según el reporte: “Mudança de tara (trabalho interno)”
Ver cita textual
O diagrama de Gantt (Anexo E) indica que o trabalho interno de uma mudança de tara pode ser executado em 30 minutos e que, no total, o tempo requerido para a mudança de tara são 42 minutos.
- Duración media del evento: 44.0 min · según el reporte: “Mudança de cápsula (trabalho interno)”
Ver cita textual
O diagrama indica que o trabalho interno de uma mudança de cápsula pode ser executado em 44 minutos e que, no total, o tempo requerido para a mudança de tara são 55 minutos.
- Duración media del evento: 69.0 min · según el reporte: “Mudança de tara e cápsula (trabalho interno)”
Ver cita textual
O diagrama indica que o trabalho interno de uma mudança de tara e cápsula pode ser executado em 69 minutos e que, no total, o tempo requerido para a mudança de tara e cápsula são 84 minutos
- Application of the Concept of Total Productive Maintenance in Automatic Bottle Filling Machines (2019)Abrir fuenteProporción del tiempo perdido: 16.4 % · según el reporte: “Set Up Losses”
Ver cita textual
Set Up Losses 5.220,00 16,36 2
- Application of the Concept of Total Productive Maintenance in Automatic Bottle Filling Machines (2019)Abrir fuenteTiempo perdido: 5,220 min · según el reporte: “Set Up Losses”
Ver cita textual
Set Up Losses 5.220,00 16,36 2
- Duración media del evento: 69.0 min · según el reporte: “Setup time”
Ver cita textual
Blowing machine Filling machine Labelling machine (bottleneck resource) Packaging machine 85 minutes 69 minutes 148 minutes 97 minutes 57 minutes 73 minutes 0 minutes 51 minutes
- Duración media del evento: 73.0 min · según el reporte: “Idle time”
Ver cita textual
Blowing machine Filling machine Labelling machine (bottleneck resource) Packaging machine 85 minutes 69 minutes 148 minutes 97 minutes 57 minutes 73 minutes 0 minutes 51 minutes
- Peningkatan Efektivitas Mesin Susu Kental Manis dengan Metode Overall Equipment Effectiveness dan Diagram Ishikawa (2021)Abrir fuenteTiempo perdido: 6.60 jam · según el reporte: “Setup & adjustment”
Ver cita textual
Failure = 97.2 Jam Setup & adjustment = 6.6 jam Downtime = 103.8 jam
- Set Up Time Reduction Using Single Minute Exchange of Dies (SMED) and 5S: A Case Study (2021)Abrir fuenteProporción del tiempo perdido: 48.0 % · según el reporte: “setup time or line preparation time”
Ver cita textual
The most significant contribution of planned stoppages is 48% comes from setup time or line preparation time.
- Set Up Time Reduction Using Single Minute Exchange of Dies (SMED) and 5S: A Case Study (2021)Abrir fuenteProporción del tiempo perdido: 2.00 % · según el reporte: “change over time”
Ver cita textual
The next is 34% of cleaning inspection and lubrication process, 19% of operational stoppages, 3% of meals or break, 2% of change over time, and the last 1% of planned maintenance.
- Set Up Time Reduction Using Single Minute Exchange of Dies (SMED) and 5S: A Case Study (2021)Abrir fuenteTiempo perdido: 34.0 min · según el reporte: “Setup time”
Ver cita textual
Before the improvement of Single Minute Exchange of Dies (SMED), the actual setup activities are eight activities in total with 34 minutes to finish the setup activities
- Performance Analysis of Filling Machine Using Overall Equipment Effectiveness Metric in Beverage Company (2023)Abrir fuenteTiempo perdido: 2,235 min · según el reporte: “Setup & Adjustment”
Ver cita textual
The second is Setup and Adjustment (30.7%), or equal to 2,235 minutes from data collection for December 2021 – March 2022.
- Performance Analysis of Filling Machine Using Overall Equipment Effectiveness Metric in Beverage Company (2023)Abrir fuenteProporción del tiempo perdido: 30.7 % · según el reporte: “Setup & Adjustment”
Ver cita textual
The second is Setup and Adjustment (30.7%), or equal to 2,235 minutes from data collection for December 2021 – March 2022.
- Analisis Overall Equipment Effectiveness untuk Meningkatkan Efektivitas Mesin Filling Multiline pada PT-XYZ (2023)Abrir fuenteTiempo perdido: 27.1 jam · según el reporte: “Setup and Adjustment Lossess”
Ver cita textual
Setup and Adjustment Lossess 27,10 27,10 53,66%
- Analisis Overall Equipment Effectiveness untuk Meningkatkan Efektivitas Mesin Filling Multiline pada PT-XYZ (2023)Abrir fuenteProporción del tiempo perdido: 53.7 % · según el reporte: “Setup and Adjustment Lossess”
Ver cita textual
Losses terbesar yang terjadi pada filling multiline 01 adalah setup and adjustment losses yaitu sebesar 27,10 jam selama bulan maret tahun 2023 atau sebesar 53,66% dari total losses yang terjadi dalam proses produksi bumbu masak di mesin filling multiline 01.
- Using Lean Manufacturing Approach for Improvement in Food Manufacturing: Case Study from Egypt (2024)Abrir fuenteTiempo perdido: 18.0 min · según el reporte: “Total time of setup”
Ver cita textual
Initial 18 11
- Using Lean Manufacturing Approach for Improvement in Food Manufacturing: Case Study from Egypt (2024)Abrir fuenteTiempo perdido: 11.0 min · según el reporte: “Internal tasks time”
Ver cita textual
Initial 18 11
- Otomatisasi Perhitungan OEE pada Mesin Filling ILAPAK 50g Menggunakan PLC dan HMI (2024)Abrir fuenteTiempo perdido: 0 mnt · según el reporte: “Setup & Adjustment”
Ver cita textual
2 Setup & Adjustment 0 0 20
- Otomatisasi Perhitungan OEE pada Mesin Filling ILAPAK 50g Menggunakan PLC dan HMI (2024)Abrir fuenteTiempo perdido: 0 mnt · según el reporte: “Setup & Adjustment”
Ver cita textual
2 Setup & Adjustment 0 0 20
- Otomatisasi Perhitungan OEE pada Mesin Filling ILAPAK 50g Menggunakan PLC dan HMI (2024)Abrir fuenteTiempo perdido: 20.0 mnt · según el reporte: “Setup & Adjustment”
Ver cita textual
2 Setup & Adjustment 0 0 20
- Lean and RCM-Based Production Model to Improve Operational Efficiency in the Production Line of a Peruvian Dairy SME (2025)Abrir fuenteProporción del tiempo perdido: 44.2 % · según el reporte: “setup time delays”
Ver cita textual
The first reason had a lot of problems that caused the filling machine to break down often (55.8% of the problems) and setup time delays (44.2% of the inefficiencies).
- Lean and RCM-Based Production Model to Improve Operational Efficiency in the Production Line of a Peruvian Dairy SME (2025)Abrir fuenteTiempo perdido: 37.5 min · según el reporte: “setup time”
Ver cita textual
The average setup time alone was 37.5 minutes, which made things much less efficient and cut down on effective working time.
- Lean and RCM-Based Production Model to Improve Operational Efficiency in the Production Line of a Peruvian Dairy SME (2025)Abrir fuenteTiempo perdido: 37.3 min · según el reporte: “setup time”
Ver cita textual
The first setup took 37.3 minutes, but after using the method, it only took 16.3 minutes.
- Lean and RCM-Based Production Model to Improve Operational Efficiency in the Production Line of a Peruvian Dairy SME (2025)Abrir fuenteTiempo perdido: 16.4 min · según el reporte: “setup time”
Ver cita textual
Setup Time minutes 37.5 18.75 16.39 -56%
- Lean and RCM-Based Production Model to Improve Operational Efficiency in the Production Line of a Peruvian Dairy SME (2025)Abrir fuenteTiempo perdido: 16.3 min · según el reporte: “setup time”
Ver cita textual
The first setup took 37.3 minutes, but after using the method, it only took 16.3 minutes.
- Proposal for improvement to increase the overall equipment effectiveness (OEE) of a dairy products company through a Preventive Maintenance Plan, Standardized Work, and SMED (2025)Abrir fuenteProporción del tiempo planificado: 1.15 % · según el reporte: “Preparación de línea”
Ver cita textual
Preparación de línea Averías / Paros Reprocesos en envasado 1,15% 7,38% 6,35%
- Proposal for improvement to increase the overall equipment effectiveness (OEE) of a dairy products company through a Preventive Maintenance Plan, Standardized Work, and SMED (2025)Abrir fuenteProporción del tiempo planificado: 1.15 % · según el reporte: “Preparación de línea”
Ver cita textual
Preparación de línea Averías / Paros ELIMINADO 1,15% 1,00%
- Enhancing Productivity through Quick Changeovers: A SMED-Based Methodology in Manufacturing Industry (2026)Abrir fuenteTiempo perdido: 120 s · según el reporte: “Filling machine setup”
Ver cita textual
4 Filling machine setup 120 120 -
- Enhancing Productivity through Quick Changeovers: A SMED-Based Methodology in Manufacturing Industry (2026)Abrir fuenteTiempo perdido: 120 s · según el reporte: “Filling machine setup”
Ver cita textual
3 Filling machine setup 120 120 -
- Proposal to Improve the Operational Availability of the Canning Machine in a Craft Brewery through the Application of Work Study, SMED, and Planned Maintenance (2026)Abrir fuenteDuración media del evento: 5.50 h · según el reporte: “setup”
Ver cita textual
the average setup time was reduced from 7.25 h to 5.50 h
- Proposal to Improve the Operational Availability of the Canning Machine in a Craft Brewery through the Application of Work Study, SMED, and Planned Maintenance (2026)Abrir fuenteDuración media del evento: 7.25 h · según el reporte: “setup”
Ver cita textual
the average setup time was reduced from 7.25 h to 5.50 h

