foratvise
Loslegen
Leerlauf und Kurzstillstände

Bottle ejection jam at blow mold

Leerlauf und KurzstillständeLeistungFormen, Gießen und Dosieren

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei etwa 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 54 % der Verlustzeit der Linie. Berichtet von 1 der 76 Studien, die sie beobachten konnten (spärliche Evidenz).

Was passiert

During the blow molding cycle a bottle fails to release cleanly from the mold cavity, either sticking to the mold wall because of inadequate cooling, mold release or part deformation, or detaching prematurely and falling out of the mold or gripper before it is properly transferred. In both cases the mold or take-out mechanism cannot complete its cycle, blocking subsequent cycles until the operator clears the obstruction or repositions the part.

Was man dagegen tut

Optimize mold cooling time and mold-release/lubrication to ensure consistent part release, verify alignment and timing of the take-out arm or gripper relative to mold opening, and inspect mold surfaces and ejector pins for wear or damage that causes sticking or premature drop.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
0,7 % [0,1–2,0 %]
Erwarteter Anteil an der Verlustzeit
0,4 % [0,1–1,1 %]
Anteil an der Verlustzeit bei Auftreten
54 % [41–66 %]
Studien / Einheiten
76 / 96
Evidenzgrad
D

Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    0,8 % [0,1–3,1 %]5 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    1,0 % [0,1–3,7 %]11 Studien
  • Bier, Wein und Spirituosen
    0,8 % [0,1–3,2 %]0 Studien
  • Backwaren und Teigwaren
    0,7 % [0,1–2,3 %]25 Studien
  • Fleisch, Geflügel und Fisch
    0,8 % [0,1–3,1 %]3 Studien
  • Obst- und Gemüseverarbeitung
    0,8 % [0,1–3,2 %]3 Studien
  • Getreide- und Ölsaatenmüllerei
    0,8 % [0,1–3,0 %]0 Studien
  • Zucker und Süßwaren
    0,7 % [0,1–2,8 %]8 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    0,8 % [0,1–2,9 %]7 Studien
  • Futtermittel und Heimtiernahrung
    0,8 % [0,1–2,8 %]6 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    0,8 % [0,1–2,9 %]8 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

During the blow molding cycle a bottle fails to release cleanly from the mold cavity, either sticking to the mold wall because of inadequate cooling, mold release or part deformation, or detaching prematurely and falling out of the mold or gripper before it is properly transferred. In both cases the mold or take-out mechanism cannot complete its cycle, blocking subsequent cycles until the operator clears the obstruction or repositions the part.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

Short machine microstops on the blow molding station with cycle time exceeding the nominal mold-open/close window, mold-open or ejector-position fault flags, and a brief drop in bottles-per-cycle count without a maintenance work order. Downstream conveying or filling stations show starvation shortly after the stop is logged.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Optimize mold cooling time and mold-release/lubrication to ensure consistent part release, verify alignment and timing of the take-out arm or gripper relative to mold opening, and inspect mold surfaces and ejector pins for wear or damage that causes sticking or premature drop.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Verlustzeit: 253 menit · laut Bericht: “Bottle Fallen Mold”
    Wörtliches Zitat anzeigen
    Bottle Fallen Mold 253
  2. Verlustzeit: 587 menit · laut Bericht: “Bottle Not Ekstrak”
    Wörtliches Zitat anzeigen
    Bottle Not Ekstrak 587
  3. Anteil an der Verlustzeit: 52,0 % · laut Bericht: “Bottle Not Ekstrak”
    Wörtliches Zitat anzeigen
    hasil dari diagram pareto menunjukkan bahwa jenis downtime terbesar adalah Bottle Not Ektrak, yang mencakup 52% dari total waktu henti mesin.