Cut-open rework of filled packages at changeover
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei weniger als 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 56 % der Verlustzeit der Linie. Berichtet von 0 der 120 Studien, die sie beobachten konnten (spärliche Evidenz).
Was passiert
During a product or format changeover on the filling machine, packages that were filled before the line settings were finalised or that remain as work-in-process do not meet specification and cannot be sold as finished goods. An operator manually cuts these packages open to recover the contained product, which is returned to the process as rework, and this manual recovery task adds non-productive time to the changeover.
Was man dagegen tut
Reduce the volume of work-in-process carried through a changeover by improving line sequencing and shutdown timing, and provide a dedicated, ergonomic station or semi-automated opener for package recovery so the task runs in parallel with, rather than inside, the changeover window. Standardise the rework-return procedure and train operators so the recovery step is executed consistently and quickly.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,3 % [0,1–1,0 %]
- Erwarteter Anteil an der Verlustzeit
- 0,2 % [0,0–0,6 %]
- Anteil an der Verlustzeit bei Auftreten
- 56 % [43–67 %]
- Studien / Einheiten
- 120 / 162
- Evidenzgrad
- D
Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,4 % [0,0–1,4 %]18 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte0,3 % [0,0–1,2 %]44 Studien
- Bier, Wein und Spirituosen0,4 % [0,0–1,5 %]16 Studien
- Backwaren und Teigwaren0,4 % [0,0–1,6 %]0 Studien
- Fleisch, Geflügel und Fisch0,4 % [0,0–1,5 %]6 Studien
- Obst- und Gemüseverarbeitung0,4 % [0,0–1,7 %]4 Studien
- Getreide- und Ölsaatenmüllerei0,4 % [0,0–1,6 %]6 Studien
- Zucker und Süßwaren0,4 % [0,0–1,6 %]3 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel0,4 % [0,0–1,6 %]6 Studien
- Futtermittel und Heimtiernahrung0,4 % [0,0–1,5 %]4 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)0,4 % [0,0–1,5 %]13 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseDuring a product or format changeover on the filling machine, packages that were filled before the line settings were finalised or that remain as work-in-process do not meet specification and cannot be sold as finished goods. An operator manually cuts these packages open to recover the contained product, which is returned to the process as rework, and this manual recovery task adds non-productive time to the changeover.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseThe filling machine state log shows an extended setup or changeover duration beyond the nominal changeover time, with the machine in a non-running manual-intervention state and no fault or stop alarm raised. Downstream counters show no good-unit output while upstream or batching systems may record a rework or return-to-process transaction tied to the same time window.
Gegenmaßnahme
Ingenieurpraktische HinweiseReduce the volume of work-in-process carried through a changeover by improving line sequencing and shutdown timing, and provide a dedicated, ergonomic station or semi-automated opener for package recovery so the task runs in parallel with, rather than inside, the changeover window. Standardise the rework-return procedure and train operators so the recovery step is executed consistently and quickly.
4Quellen
- Set Up Time Reduction Using Single Minute Exchange of Dies (SMED) and 5S: A Case Study (2021)Quelle öffnenVerlustzeit: 3,00 min · laut Bericht: “Cut Open Rework”
Wörtliches Zitat anzeigen
Cut Open Rework 0:28:00 0:31:00 0:03:00

