foratvise
Loslegen
planned downtime

CIP wash cycle stop

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei etwa 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 58 % der Verlustzeit der Linie. Berichtet von 1 der 129 Studien, die sie beobachten konnten (spärliche Evidenz).

Was passiert

The line or associated equipment is held in a non-production state while the Clean-in-Place system executes its scheduled wash, rinse and sanitize phases, so no product can be processed until the cycle completes. Extended or abnormal wash durations can push what is normally a planned sanitation stop into an unplanned equipment-related delay.

Was man dagegen tut

Schedule CIP cycles during planned non-production windows where possible and optimize phase times and chemical/flow parameters to shorten the cycle without compromising sanitation. Install parallel CIP sets or buffer capacity to decouple cleaning from production, and monitor cycle duration trends to detect and correct abnormally long washes caused by valve, pump or sensor malfunctions.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
0,5 % [0,1–1,5 %]
Erwarteter Anteil an der Verlustzeit
0,3 % [0,1–0,9 %]
Anteil an der Verlustzeit bei Auftreten
58 % [47–69 %]
Studien / Einheiten
129 / 163
Evidenzgrad
D

Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    0,6 % [0,1–2,2 %]13 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    0,5 % [0,1–1,9 %]27 Studien
  • Bier, Wein und Spirituosen
    0,6 % [0,1–2,3 %]11 Studien
  • Backwaren und Teigwaren
    0,6 % [0,1–2,0 %]24 Studien
  • Fleisch, Geflügel und Fisch
    0,6 % [0,1–2,2 %]9 Studien
  • Obst- und Gemüseverarbeitung
    0,7 % [0,1–2,6 %]7 Studien
  • Getreide- und Ölsaatenmüllerei
    0,6 % [0,1–2,3 %]6 Studien
  • Zucker und Süßwaren
    0,6 % [0,1–2,4 %]9 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    0,6 % [0,1–2,3 %]5 Studien
  • Futtermittel und Heimtiernahrung
    0,6 % [0,1–2,2 %]7 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    0,9 % [0,1–3,4 %]11 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

The line or associated equipment is held in a non-production state while the Clean-in-Place system executes its scheduled wash, rinse and sanitize phases, so no product can be processed until the cycle completes. Extended or abnormal wash durations can push what is normally a planned sanitation stop into an unplanned equipment-related delay.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

CIP controller or line state log shows a transition into wash/rinse/sanitize/drain phases with the downstream line in a stopped or standby state; MES records a downtime event tagged to the CIP system with a logged duration, and outlier events with unusually long durations appear as the recorded maxima. Flow, temperature and conductivity trends on the CIP skid confirm the active phase sequence during the stop.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Schedule CIP cycles during planned non-production windows where possible and optimize phase times and chemical/flow parameters to shorten the cycle without compromising sanitation. Install parallel CIP sets or buffer capacity to decouple cleaning from production, and monitor cycle duration trends to detect and correct abnormally long washes caused by valve, pump or sensor malfunctions.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Verlustzeit: 16,0 h · laut Bericht: “CIP wash stop”
    Wörtliches Zitat anzeigen
    The stop that represents the largest proportion is the CIP wash stop, which represents a stop time of approximately 16 hours.
  2. Verlustzeit: 26,0 h · laut Bericht: “CIP wash stop (maximum recorded)”
    Wörtliches Zitat anzeigen
    the plant management recorded washing times that exceeded the planned one, occupying a maximum of 26 stop-page hours