Scheduled cleaning, inspection and lubrication of the filler
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 56 % der Verlustzeit der Linie. Berichtet von 1 der 120 Studien, die sie beobachten konnten (spärliche Evidenz).
Was passiert
The filling machine is taken offline on a scheduled basis so operators or maintenance staff can clean the equipment and surrounding area, visually inspect components, and apply lubrication to moving parts as part of routine autonomous or preventive maintenance. This is a planned activity rather than a reaction to a fault, and it is often bundled with changeover cleaning when it falls close to a product or format change.</p>
Was man dagegen tut
Standardize cleaning, inspection and lubrication tasks into checklists embedded in an autonomous maintenance or total productive maintenance program, and schedule them during low-demand windows or combine them efficiently with planned changeovers. Applying single-minute exchange of die principles to separate internal and external tasks can shorten the time the filler remains stopped for these routine activities.</p>
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,6 % [0,1–1,5 %]
- Erwarteter Anteil an der Verlustzeit
- 0,3 % [0,1–0,9 %]
- Anteil an der Verlustzeit bei Auftreten
- 56 % [45–67 %]
- Studien / Einheiten
- 120 / 162
- Evidenzgrad
- D
Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,6 % [0,1–2,1 %]18 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte0,5 % [0,1–1,7 %]44 Studien
- Bier, Wein und Spirituosen0,6 % [0,1–2,2 %]16 Studien
- Backwaren und Teigwaren0,7 % [0,1–2,5 %]0 Studien
- Fleisch, Geflügel und Fisch0,6 % [0,1–2,3 %]6 Studien
- Obst- und Gemüseverarbeitung0,7 % [0,1–2,5 %]4 Studien
- Getreide- und Ölsaatenmüllerei0,7 % [0,1–2,5 %]6 Studien
- Zucker und Süßwaren0,7 % [0,1–2,4 %]3 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel0,6 % [0,1–2,2 %]6 Studien
- Futtermittel und Heimtiernahrung0,7 % [0,1–2,4 %]4 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)0,9 % [0,1–3,3 %]13 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseThe filling machine is taken offline on a scheduled basis so operators or maintenance staff can clean the equipment and surrounding area, visually inspect components, and apply lubrication to moving parts as part of routine autonomous or preventive maintenance. This is a planned activity rather than a reaction to a fault, and it is often bundled with changeover cleaning when it falls close to a product or format change.</p>
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseThe line logs a planned stop or maintenance machine state with a regular, recurring pattern rather than isolated fault alarms, and the stop reason code typically references cleaning, inspection or lubrication rather than a specific failure. Duration tends to be consistent across occurrences and no abnormal sensor trends precede the stop, distinguishing it from unplanned equipment failure.</p>
Gegenmaßnahme
Ingenieurpraktische HinweiseStandardize cleaning, inspection and lubrication tasks into checklists embedded in an autonomous maintenance or total productive maintenance program, and schedule them during low-demand windows or combine them efficiently with planned changeovers. Applying single-minute exchange of die principles to separate internal and external tasks can shorten the time the filler remains stopped for these routine activities.</p>
4Quellen
- Set Up Time Reduction Using Single Minute Exchange of Dies (SMED) and 5S: A Case Study (2021)Quelle öffnenAnteil an der Verlustzeit: 34,0 % · laut Bericht: “cleaning inspection and lubrication process”
Wörtliches Zitat anzeigen
The next is 34% of cleaning inspection and lubrication process, 19% of operational stoppages, 3% of meals or break, 2% of change over time, and the last 1% of planned maintenance.
- Set Up Time Reduction Using Single Minute Exchange of Dies (SMED) and 5S: A Case Study (2021)Quelle öffnenVerlustzeit: 7,00 min · laut Bericht: “Cleaning Environment”
Wörtliches Zitat anzeigen
Take Cleaning Tools 0:02:00 0:04:00 0:02:00; Cleaning floor below the machine 0:04:00 0:07:00 0:03:00; Tidy Up Cleaning Tools 0:07:00 0:09:00 0:02:00

