foratvise
Loslegen
Anlagenausfall (Störungen)

Compressed air leak

Anlagenausfall (Störungen)VerfügbarkeitFormen, Gießen und Dosieren

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei etwa 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 57 % der Verlustzeit der Linie. Berichtet von 1 der 76 Studien, die sie beobachten konnten (spärliche Evidenz).

Was passiert

Wear, cracking or loosening of pneumatic fittings, hoses, seals or valves in the compressed air circuit allows air to escape, so the forming actuators or cylinders lose the pressure and flow needed to complete their stroke reliably. As leakage increases the system struggles to maintain setpoint pressure, degrading actuator force and timing until the equipment can no longer operate and a repair intervention is required.

Was man dagegen tut

Implement a routine ultrasonic or soap-test leak detection and tagging program on the compressed air network, with prioritized repair or replacement of degraded fittings, hoses and seals. Reinforce preventive maintenance on pneumatic connections at the forming station and consider pressure monitoring with automated low-pressure alerts to trigger corrective action before the loss propagates to a stop.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
0,7 % [0,1–1,9 %]
Erwarteter Anteil an der Verlustzeit
0,4 % [0,1–1,1 %]
Anteil an der Verlustzeit bei Auftreten
57 % [46–67 %]
Studien / Einheiten
76 / 96
Evidenzgrad
D

Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    0,8 % [0,1–3,2 %]5 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    1,1 % [0,1–4,0 %]11 Studien
  • Bier, Wein und Spirituosen
    0,9 % [0,1–3,4 %]0 Studien
  • Backwaren und Teigwaren
    0,7 % [0,1–2,5 %]25 Studien
  • Fleisch, Geflügel und Fisch
    0,8 % [0,1–3,1 %]3 Studien
  • Obst- und Gemüseverarbeitung
    0,8 % [0,1–3,1 %]3 Studien
  • Getreide- und Ölsaatenmüllerei
    0,9 % [0,1–3,6 %]0 Studien
  • Zucker und Süßwaren
    0,8 % [0,1–3,1 %]8 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    0,8 % [0,1–2,8 %]7 Studien
  • Futtermittel und Heimtiernahrung
    0,8 % [0,1–3,1 %]6 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    0,8 % [0,1–2,9 %]8 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

Wear, cracking or loosening of pneumatic fittings, hoses, seals or valves in the compressed air circuit allows air to escape, so the forming actuators or cylinders lose the pressure and flow needed to complete their stroke reliably. As leakage increases the system struggles to maintain setpoint pressure, degrading actuator force and timing until the equipment can no longer operate and a repair intervention is required.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

SCADA shows a sustained drop in compressed air header or local line pressure below setpoint, with the compressor or air receiver running more frequently or continuously to compensate, and low-pressure alarms on the forming station. The affected forming machine state log shows unplanned stop or fault state correlated with the pressure excursion, often with repeated cycle-time or actuator-position deviations preceding the stop.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Implement a routine ultrasonic or soap-test leak detection and tagging program on the compressed air network, with prioritized repair or replacement of degraded fittings, hoses and seals. Reinforce preventive maintenance on pneumatic connections at the forming station and consider pressure monitoring with automated low-pressure alerts to trigger corrective action before the loss propagates to a stop.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Anteil an den Verlustereignissen: 26,0 % · laut Bericht: “Vazamento de ar comprimido”
    Wörtliches Zitat anzeigen
    O vazamento de ar comprimido também não foi validado como causa- raiz pois representava apenas 26 % das falhas, porém a equipe tomou como ação preventiva substituir todas as mangueiras de ar comprimido