Electrical fault in filling/weighing equipment
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 58 % der Verlustzeit der Linie. Berichtet von 2 der 120 Studien, die sie beobachten konnten (begrenzte Evidenz).
Was passiert
A fault in motors, drives, control relays, wiring or power supply interrupts normal operation of the filler or scale, causing the machine to stop until the electrical circuit or component is restored. This may also manifest as loss of calibration signal integrity in load cells or sensors, which the control system interprets as a fault condition.
Was man dagegen tut
Implement preventive electrical maintenance including periodic inspection of wiring, contacts and drives, scheduled recalibration and verification of weighing/load-cell circuits, and use of surge protection or redundant power supplies to reduce fault recurrence.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,8 % [0,2–1,8 %]
- Erwarteter Anteil an der Verlustzeit
- 0,4 % [0,1–1,1 %]
- Anteil an der Verlustzeit bei Auftreten
- 58 % [47–68 %]
- Studien / Einheiten
- 120 / 162
- Evidenzgrad
- C
Grad C: 2 bis 4 Studien oder eine Intervallbreite über 0,35.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,8 % [0,1–2,8 %]18 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte0,9 % [0,1–2,6 %]44 Studien
- Bier, Wein und Spirituosen1,2 % [0,2–3,8 %]16 Studien
- Backwaren und Teigwaren0,9 % [0,1–3,3 %]0 Studien
- Fleisch, Geflügel und Fisch0,9 % [0,1–3,0 %]6 Studien
- Obst- und Gemüseverarbeitung0,9 % [0,1–3,3 %]4 Studien
- Getreide- und Ölsaatenmüllerei0,9 % [0,1–3,0 %]6 Studien
- Zucker und Süßwaren0,9 % [0,1–3,2 %]3 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel0,9 % [0,1–3,0 %]6 Studien
- Futtermittel und Heimtiernahrung0,9 % [0,1–3,1 %]4 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)0,8 % [0,1–2,7 %]13 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseA fault in motors, drives, control relays, wiring or power supply interrupts normal operation of the filler or scale, causing the machine to stop until the electrical circuit or component is restored. This may also manifest as loss of calibration signal integrity in load cells or sensors, which the control system interprets as a fault condition.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseSCADA/MES logs show an unplanned stop state with an electrical or fault alarm code tagged to the filler or scale, often preceded by erratic sensor or load-cell readings, voltage/current fluctuations, or communication dropouts; the stop duration is irregular and ends only after a maintenance reset or repair event is logged.
Gegenmaßnahme
Ingenieurpraktische HinweiseImplement preventive electrical maintenance including periodic inspection of wiring, contacts and drives, scheduled recalibration and verification of weighing/load-cell circuits, and use of surge protection or redundant power supplies to reduce fault recurrence.
4Quellen
- Anteil an den Verlustereignissen: 67,0 % · laut Bericht: “Scale calibration and electrical failures”
Wörtliches Zitat anzeigen
os problemas com a balança representavam 67 % das paradas na enchedora, e destes problemas, os elétricos representavam 98 % das paradas
- Proposal to Improve the Operational Availability of the Canning Machine in a Craft Brewery through the Application of Work Study, SMED, and Planned Maintenance (2026)Quelle öffnenZeit zwischen Ereignissen: 171 h · laut Bericht: “electrical failure”
Wörtliches Zitat anzeigen
Furthermore, the mechanical MTBF increased from 98.74 h to 117.25 h, while the electrical MTBF increased from 144.31 h to 170.55 h.
- Proposal to Improve the Operational Availability of the Canning Machine in a Craft Brewery through the Application of Work Study, SMED, and Planned Maintenance (2026)Quelle öffnenMittlere Ereignisdauer: 5,17 h · laut Bericht: “electrical failure”
Wörtliches Zitat anzeigen
the electrical MTTR decreased from 7.20 h to 5.17 h
- Proposal to Improve the Operational Availability of the Canning Machine in a Craft Brewery through the Application of Work Study, SMED, and Planned Maintenance (2026)Quelle öffnenZeit zwischen Ereignissen: 144 h · laut Bericht: “electrical failure”
Wörtliches Zitat anzeigen
Furthermore, the mechanical MTBF increased from 98.74 h to 117.25 h, while the electrical MTBF increased from 144.31 h to 170.55 h.
- Proposal to Improve the Operational Availability of the Canning Machine in a Craft Brewery through the Application of Work Study, SMED, and Planned Maintenance (2026)Quelle öffnenMittlere Ereignisdauer: 7,20 h · laut Bericht: “electrical failure”
Wörtliches Zitat anzeigen
the electrical MTTR decreased from 7.20 h to 5.17 h

