foratvise
Loslegen
Prozessfehler (Ausschuss und Nacharbeit)

Fill content or contamination defect

Prozessfehler (Ausschuss und Nacharbeit)QualitätAbfüllen

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei etwa 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 48 % der Verlustzeit der Linie. Berichtet von 2 der 120 Studien, die sie beobachten konnten (begrenzte Evidenz).

Was passiert

Variability in the dosing or filling valve, flow meter drift, or changes in product viscosity and temperature cause the delivered volume or weight of product (for example oil content) to fall below specification. Separately, ingress of foreign matter, residual cleaning or sanitising agents, or microbial contamination during the filling step renders units unfit for use even when the fill level itself is correct.

Was man dagegen tut

Calibrate and periodically verify dosing valves, pumps and flow meters against reference standards, and compensate for product viscosity and temperature in the filling control logic. Reinforce cleaning and sanitation validation, use foreign-particle or seal-integrity detection where applicable, and route borderline units to checkweighing and quality inspection before release.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
0,7 % [0,2–2,0 %]
Erwarteter Anteil an der Verlustzeit
0,4 % [0,1–1,0 %]
Anteil an der Verlustzeit bei Auftreten
48 % [37–60 %]
Studien / Einheiten
120 / 162
Evidenzgrad
C

Grad C: 2 bis 4 Studien oder eine Intervallbreite über 0,35.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    0,8 % [0,1–2,8 %]18 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    0,9 % [0,1–2,5 %]44 Studien
  • Bier, Wein und Spirituosen
    0,8 % [0,1–2,7 %]16 Studien
  • Backwaren und Teigwaren
    0,9 % [0,1–3,5 %]0 Studien
  • Fleisch, Geflügel und Fisch
    0,8 % [0,1–2,9 %]6 Studien
  • Obst- und Gemüseverarbeitung
    0,9 % [0,1–3,2 %]4 Studien
  • Getreide- und Ölsaatenmüllerei
    1,3 % [0,2–4,6 %]6 Studien
  • Zucker und Süßwaren
    0,9 % [0,1–3,2 %]3 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    0,9 % [0,1–3,1 %]6 Studien
  • Futtermittel und Heimtiernahrung
    0,9 % [0,1–3,2 %]4 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    0,8 % [0,1–2,8 %]13 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

Variability in the dosing or filling valve, flow meter drift, or changes in product viscosity and temperature cause the delivered volume or weight of product (for example oil content) to fall below specification. Separately, ingress of foreign matter, residual cleaning or sanitising agents, or microbial contamination during the filling step renders units unfit for use even when the fill level itself is correct.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

In-line checkweigher or flow totaliser readings trend below the target setpoint with increasing reject counts at the filling station; dosing valve or pump actuator signals show drift or erratic cycles. Contamination events are less directly visible in SCADA but may correlate with CIP cycle timing, missed sanitation confirmations, or downstream quality-inspection reject spikes without any corresponding deviation in fill-level signals.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Calibrate and periodically verify dosing valves, pumps and flow meters against reference standards, and compensate for product viscosity and temperature in the filling control logic. Reinforce cleaning and sanitation validation, use foreign-particle or seal-integrity detection where applicable, and route borderline units to checkweighing and quality inspection before release.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Anteil an den Verlustereignissen: 15,0 % · laut Bericht: “Less Content Oil”
    Wörtliches Zitat anzeigen
    Less Content Oil 676 15
  2. Anzahl der Ereignisse: 676 units · laut Bericht: “Less Content Oil”
    Wörtliches Zitat anzeigen
    Less Content Oil 676 15
  3. Anzahl der Ereignisse: 8.124 cases · laut Bericht: “Contaminated”
    Wörtliches Zitat anzeigen
    Among these, underfill defects were the most frequent, with a total of 20,598 cases, followed by uncrowned bottles with 14,508 cases, and contamination with 8,124 cases.