foratvise
Loslegen
Rüsten und Einstellen

Film and film-holding equipment changeover

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei etwa 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 56 % der Verlustzeit der Linie. Berichtet von 1 der 112 Studien, die sie beobachten konnten (spärliche Evidenz).

Was passiert

To switch to a different film size or specification, the operator must stop the packaging machine, remove the current film reel and its holding/mounting fixtures, fit the new reel and adjust the holders, guides and sealing elements to the new dimensions, then verify tracking and seal quality before resuming production. This mechanical reconfiguration consumes non-productive time between the last good pack of the previous run and the first good pack of the new run.

Was man dagegen tut

Apply quick-changeover (SMED) principles: pre-stage the new film reel and holding fixtures near the line, use standardized or tool-less quick-release holders, and pre-set guide and sealing adjustments offline on a secondary fixture so only final fine-tuning is done on the running machine. Sequencing production to group runs by similar film size further reduces the frequency and duration of these changeovers.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
0,5 % [0,1–1,4 %]
Erwarteter Anteil an der Verlustzeit
0,3 % [0,1–0,8 %]
Anteil an der Verlustzeit bei Auftreten
56 % [44–67 %]
Studien / Einheiten
112 / 155
Evidenzgrad
D

Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    0,6 % [0,1–1,9 %]14 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    0,7 % [0,1–2,3 %]33 Studien
  • Bier, Wein und Spirituosen
    0,6 % [0,1–2,1 %]14 Studien
  • Backwaren und Teigwaren
    0,6 % [0,1–2,1 %]6 Studien
  • Fleisch, Geflügel und Fisch
    0,6 % [0,1–2,4 %]6 Studien
  • Obst- und Gemüseverarbeitung
    0,6 % [0,1–2,3 %]4 Studien
  • Getreide- und Ölsaatenmüllerei
    0,6 % [0,1–2,3 %]4 Studien
  • Zucker und Süßwaren
    0,6 % [0,1–2,2 %]4 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    0,6 % [0,1–2,2 %]8 Studien
  • Futtermittel und Heimtiernahrung
    0,6 % [0,1–2,2 %]5 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    0,6 % [0,1–2,0 %]14 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

To switch to a different film size or specification, the operator must stop the packaging machine, remove the current film reel and its holding/mounting fixtures, fit the new reel and adjust the holders, guides and sealing elements to the new dimensions, then verify tracking and seal quality before resuming production. This mechanical reconfiguration consumes non-productive time between the last good pack of the previous run and the first good pack of the new run.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

SCADA/MES shows an extended machine-stopped or changeover state between two production orders with no fault alarm active, often tagged manually by the operator as a format or size change. Downstream conveyors show starvation while upstream units may continue running, and the event log records a changeover reason code aligned with a product or film-size code change.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Apply quick-changeover (SMED) principles: pre-stage the new film reel and holding fixtures near the line, use standardized or tool-less quick-release holders, and pre-set guide and sealing adjustments offline on a secondary fixture so only final fine-tuning is done on the running machine. Sequencing production to group runs by similar film size further reduces the frequency and duration of these changeovers.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Verlustzeit: 5,00 min · laut Bericht: “Changing the film guide bar to a double bar”
    Wörtliches Zitat anzeigen
    เปลี่ยนราว (Bar) พาฟิล์ม เป็นราวคู่ 1 5
  2. Verlustzeit: 10,0 min · laut Bericht: “Changing film size and film-holding equipment”
    Wörtliches Zitat anzeigen
    เปลี่ยนขนาดฟิล์ม และอุปกรณ์ช่วยยึดฟิล์ม 1 10