foratvise
Loslegen
Abfüll- und Verpackungslinie

Verpacken (Formen, Siegeln, Einschlagen, Kartonieren, Palettieren)

Heat sealing in intermittent-motion form-fill-seal packaging

Validiertes ModellOEE-Grenze 0,986 [0,959–0,995]20.000 Monte-Carlo-Stichproben · Seed 20261115 · berechnet am 16. November 2026

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Verpacken (Formen, Siegeln, Einschlagen, Kartonieren, Palettieren) kann höchstens 99 von je 100 geplanten Stunden nutzen. Der Rest entfällt auf Grenzen, die kein Werk vermeiden kann.

  1. 99höchstens nutzbar
  2. 1sind physikalische Grenze

Die drei Grenzen, die das festlegen

Laufzeit: bis 100 %

Der Rest sind Stillstände, die Physik oder Vorschrift erzwingen: Reinigung, Umrüsten, Abtauen.

Geschwindigkeit: bis 99 %

Wie nah an ihrer Höchstgeschwindigkeit sie laufen kann, ohne Produkt oder Anlage zu schädigen.

Gutprodukt: bis 100 %

Ein Teil des Produkts liegt auch bei gut beherrschtem Prozess außerhalb der Spezifikation.

Das technische Detail ansehen

Technisches Detail

Unsicherheitsintervalle, physikalische Modelle je Station und Quellen, für alle, die jede Zahl prüfen möchten.

1Szenario

A vertical form-fill-seal machine forms pillow bags of frozen vegetables or a similar dry product from a reel of polyethylene film. Each cycle the film is advanced by one bag length, the cross-sealing jaws close on two layers of film, hold them at constant jaw temperature for the dwell time (the top seal of one bag and the bottom seal of the next are made together) and open again. The longitudinal fin seal is made while the film advances. The cross-seal dwell is the physics-limited step.

Herkunft der EingangsgrößenBerechnet1Deklarierte Annahme27Verifiziertes Zitat8

2Ergebnisse

Punktwert aus den Nominalparametern und 95-%-Intervall aus 20.000 Monte-Carlo-Ziehungen der unsicheren Parameter.
  • Density of the semicrystalline sealant film (two-phase rule)914 [900–928] kg/m³
  • Specific heat of the semicrystalline film (crystalline and amorphous heat capacities weighted by crystallinity)1,95 [1,89–2,01] kJ/kg/K
  • Thermal diffusivity of the film0,186 [0,143–0,250] mm²/s
  • Fourier number at which the seal interface reaches the sealing temperature0,676 [0,584–0,819]
  • TheoretischMinimum jaw dwell time (interface reaches the sealing temperature, ideal contact)0,00911 [0,00405–0,02034] s
  • Dwell time with the capability margin (jaw-temperature and film-thickness tolerances; declared tolerances, not a documented BAT)0,0146 [0,0064–0,0346] s
  • TypischDwell time in operation (declared scenario)0,300 [0,162–0,589] s
  • Minimum indexing time per cycle (film advance and jaw stroke, bang-bang motion)0,370 [0,283–0,464] s
  • TheoretischMaximum cycles per minute with the minimum dwell158 [126–205] 1/min
  • Cycles per minute with the capability-limited dwell (the rate of the capable process)156 [125–202] 1/min
  • TypischCycles per minute with the operating dwell (declared scenario)89,6 [61,2–122,7] 1/min
  • Film mass in the seal areas per pack (two layers)0,393 [0,282–0,544] g
  • TheoretischThermodynamic minimum energy per pack (the seal returns to ambient)0 J
  • Minimum heating duty per pack without heat recovery (seal mass at the sealing temperature, fusion included; a computed minimum, not a documented BAT)124 [87–182] J
  • Heat absorbed per pack by the film at the capability-limited dwell (conductive jaws)141 [100–207] J
  • TypischHeat absorbed per pack by the film at the operating dwell (film close to jaw temperature)147 [104–214] J
  • Minimum sealing heat per kg of packed product0,247 [0,175–0,365] kJ/kg
  • Sealing heat absorbed by the film per kg of packed product at the operating dwell0,293 [0,207–0,429] kJ/kg
  • Nominal interface temperature at the capability-limited dwell139 [126–152] °C
  • Standard deviation of the interface temperature at the capability-limited dwell4,01 [2,77–5,59] K
  • Share of seals whose interface stays below the sealing temperature9,75 × 10⁻⁷ [4,14 × 10⁻⁹–8,55 × 10⁻⁵]
  • Share of seals overheated beyond the upper limit of the sealing window7,62 × 10⁻²⁴ [1,87 × 10⁻¹²⁰–1,10 × 10⁻⁶]
  • TheoretischMaximum OEE quality factor (seal integrity)1,00000 [0,99990–1,00000]
  • Mean film speed at the capability-limited rate39,0 [31,1–50,4] m/min
  • Run time of one reel at the capability-limited rate51,2 [25,6–109,0] min
  • TheoretischMaximum film yield (splice and start-up waste)0,9982 [0,9955–0,9994]
  • TheoretischMaximum availability (no stop is forced by physics or regulation: reel splices are removable by an automatic splicer, changeovers are scenario)1,00
  • Availability with declared manual splices and changeovers0,909 [0,815–0,963]
  • TheoretischPerformance factor: minimum cycle over capability-limited cycle0,986 [0,959–0,995]
  • TheoretischPhysics-bounded OEE0,986 [0,959–0,995]
  • OEE with declared manual splices and changeovers0,896 [0,799–0,950]

3Obergrenzen je Dimension

Jede Dimension zeigt die vom Modell berechneten Obergrenzen und, bei vergleichbaren Einheiten, dokumentierte Vergleichswerte. Farbe und Markerform kennzeichnen den Grenztyp im gesamten Orakel.
  • Theoretisch
  • Beste verfügbare Technik
  • Best dokumentiert
  • Typisch
Zyklus- oder Verweilzeits · niedriger ist besser
  • TheoretischMinimum jaw dwell time (interface reaches the sealing temperature, ideal contact)0,00911 [0,00405–0,02034] s
  • TypischDwell time in operation (declared scenario)0,300 [0,162–0,589] s
Durchsatz1/min · höher ist besser
  • TheoretischMaximum cycles per minute with the minimum dwell158 [126–205] 1/min
  • TypischCycles per minute with the operating dwell (declared scenario)89,6 [61,2–122,7] 1/min
Energie je ProdukteinheitJ · niedriger ist besser
  • TheoretischThermodynamic minimum energy per pack (the seal returns to ambient)0 J
  • TypischHeat absorbed per pack by the film at the operating dwell (film close to jaw temperature)147 [104–214] J
Qualitäthöher ist besser
  • TheoretischMaximum OEE quality factor (seal integrity)1,00000 [0,99990–1,00000]
Ausbeutehöher ist besser
  • TheoretischMaximum film yield (splice and start-up waste)0,9982 [0,9955–0,9994]
Verfügbarkeithöher ist besser
  • TheoretischMaximum availability (no stop is forced by physics or regulation: reel splices are removable by an automatic splicer, changeovers are scenario)1,00
Leistunghöher ist besser
  • TheoretischPerformance factor: minimum cycle over capability-limited cycle0,986 [0,959–0,995]
OEEhöher ist besser
  • TheoretischPhysics-bounded OEE0,986 [0,959–0,995]

4Verlustkaskade

Was jede Obergrenze von der nächsten trennt, von der physikalischen Grenze bis zum typischen Betrieb.
  1. TheoretischTypischZyklus- oder Verweilzeit
    0,00911 [0,00405–0,02034] s → 0,300 [0,162–0,589] s (Abstand 0,291 s)

    The minimum dwell brings the nominal seal interface exactly to the sealing temperature with ideal (zero-resistance) contact between jaw and film. Any real jaw temperature oscillates around its set point and the film thickness varies along the web, so a capable process must hold the jaws until the interface is z standard deviations of jaw temperature above the sealing temperature on the thickest film of the tolerance band. Because the remaining temperature difference decays exponentially with the Fourier number, the last few kelvin cost a disproportionate share of the dwell. Operating dwells are one or two orders of magnitude longer than the conduction limit of a bare polyethylene film. The causes are thermal resistances that the ideal model leaves out: non-stick jaw covers, imperfect contact on wrinkles and fin overlaps, outer laminate layers (oriented polypropylene or polyester) that must be crossed before the sealant, the latent heat of melting that slows the advance of the melt front, and the time the molten interface needs for chain interdiffusion and for the seal to gain strength while still under pressure.

  2. TheoretischTypischDurchsatz
    158 [126–205] 1/min → 89,6 [61,2–122,7] 1/min (Abstand 68,8 1/min)

    With the indexing motion (film advance and jaw stroke) fixed by the acceleration the film and the carriage can stand, the cycle rate falls from the theoretical value (minimum dwell) to the capable value and then to the operating value in proportion to the dwell gaps above; at operating dwells the dwell, not the motion, dominates the cycle.

  3. TheoretischTypischEnergie je Produkteinheit
    0 J → 147 [104–214] J (Abstand 147 J)

    The seal is heated and cools back to ambient, so in the reversible limit (ideal heat recovery) no net energy is needed: the thermodynamic minimum is zero, as in the DOE bandwidth study. Without heat recovery the least heat is that of raising only the seal mass to the sealing temperature and melting its crystalline fraction. Conductive jaws at a constant temperature above the sealing temperature heat the whole film thickness towards the jaw temperature; at operating dwells the film reaches it, so the absorbed heat grows with (T_jaw - T0) instead of (T_s - T0). The heat absorbed by the film is still a small fraction of the electricity of the machine: jaw heaters lose heat continuously by convection and radiation and through the jaw mountings, and the drives, vacuum and compressed air dominate the energy of a packaging step, which is why the documented energy intensities of packaging are orders of magnitude above the sealing heat.

5Physikalisch begrenzte OEE

Die höchste OEE, die die Operation erreichen kann: Verfügbarkeit, Leistung und Qualität, begrenzt nur durch unvermeidbare Stillstände und physikalische Prozessfähigkeit.
Anteil der Belegungszeit, der nach jedem unvermeidbaren Verlust verbleibt. Die Achse beginnt bei 0,90.
  • Belegungszeit (ideal)
    1,000
  • Verfügbarkeit
    Faktor 1,00
    1,000 (−0,000)
  • Leistung
    Faktor 0,986 [0,959–0,995]
    0,986 (−0,014)
  • Qualität
    Faktor 1,00000 [0,99990–1,00000]
    0,986 (−0,000)
  • Physikalisch begrenzte OEE
    0,986 [0,959–0,995]

6Vollständige Herleitung

Massen- und Energiebilanzen, geschwindigkeitsbestimmender Schritt, Prozessfähigkeit und unvermeidbare Stillstände, mit Erläuterung jedes Terms.

Scope. An intermittent-motion vertical form-fill-seal machine makes pillow bags from a reel of polyethylene film. Each cycle the film advances one bag length, the cross-sealing jaws close on two film layers, hold them at a constant jaw temperature for the dwell time and open again; the longitudinal fin seal is made while the film moves. The cross-seal dwell is the physics-limited step. Symbols and their values, units, uncertainty distributions and sources are listed in the parameter table generated from config/physics/packaging.yaml. Numbers quoted here are point values; the output table gives the Monte Carlo intervals.

1. Mass balance — maximum film yield

Sealing consumes no product and no film: the seal is part of the bag. Film is lost only where it does not become a saleable bag. In a fin-sealed pillow bag there is no trim, so two losses remain:

  • Splice waste. A reel holds a finite length LrL_r. When it runs out the new web is spliced to the old one and a length LwL_w around the splice is discarded.
  • Start-up waste. After each changeover the machine needs nsun_{su} bags to stabilise registration, bag length and seal quality.

During a production campaign of duration tcampt_{camp} at web speed vv the film used for good bags is Lcamp=v tcampL_{camp} = v\,t_{camp}, the number of reels is nr=Lcamp/Lrn_r = L_{camp}/L_r, and

Ymax=LcampLcamp+nrLw+nsuLp=0.998,Y_{max} = \frac{L_{camp}}{L_{camp} + n_r L_w + n_{su} L_p} = 0.998,

where LpL_p is the film length per bag. No open source documents splice or start-up waste, so LwL_w and nsun_{su} are declared scenario values.

2. Energy balance — minimum energy per pack

Film properties. The sealant is semicrystalline polyethylene with mass crystallinity wcw_c. Its density follows the two-phase rule from the densities of the crystalline and amorphous phases at 298 K (ρc\rho_c = 1.0030 and ρa\rho_a = 0.8519 Mg/m³, Gaur and Wunderlich, 1981):

1ρ=wcρc+1−wcρa  ⇒  ρ=914 kg/m3.\frac{1}{\rho} = \frac{w_c}{\rho_c} + \frac{1-w_c}{\rho_a} \;\Rightarrow\; \rho = 914\ \text{kg/m}^3 .

The specific heat weights the recommended heat capacities of crystalline and amorphous polyethylene at 310 K (Cp,cC_{p,c} = 22.38 and Cp,aC_{p,a} = 31.33 J/(mol K) per CH2 repeat unit, MM = 14.027 g/mol):

cp=wcCp,c+(1−wc)Cp,aM=1.95 kJ/(kg K).c_p = \frac{w_c C_{p,c} + (1-w_c) C_{p,a}}{M} = 1.95\ \text{kJ/(kg K)} .

Heat capacity rises with temperature, so using the 310 K value over the whole heating range underestimates the sensible heat: every energy computed with it is a lower bound. Melting the crystalline fraction absorbs wc Δhf/Mw_c\,\Delta h_f/M, with the heat of fusion of fully crystalline polyethylene Δhf\Delta h_f = 4.051 kJ/mol at 380 K.

Seal mass. The cross seal covers the bag width WW times the jaw height hjh_j (the top seal of one bag and the bottom seal of the next), the fin seal the bag length LpL_p times the fin width wfw_f; both join two layers of thickness LL:

ms=ρ (Whj+Lpwf) 2L=0.39 g per pack.m_s = \rho\,(W h_j + L_p w_f)\,2L = 0.39\ \text{g per pack}.

Thermodynamic minimum. The seal is heated, fused and cooled back to ambient: its final state equals its initial state except for the new bond, whose interfacial energy is negligible. In the reversible limit all the heat could be recovered (ideal regeneration), so the thermodynamic minimum is zero, in agreement with the zero thermodynamic minimum the DOE bandwidth study assigns to packaging.

Minimum heating duty without recovery. Without heat recovery, the least heat is that of bringing the seal mass to the sealing temperature TsT_s and melting its crystalline fraction. Heat flows from the jaw to the interface, so when the interface reaches TsT_s every point between jaw and interface is at least at TsT_s; uniform heating to TsT_s is therefore the lowest possible duty:

Qmin=ms[cp(Ts−T0)+wc ΔhfM]=124 J per pack.Q_{min} = m_s\left[c_p (T_s - T_0) + \frac{w_c\,\Delta h_f}{M}\right] = 124\ \text{J per pack}.

Conductive jaws. A jaw held at Tj>TsT_j > T_s heats the film towards TjT_j. The heat absorbed after a dwell tt follows from the mean temperature of the plane wall (Section 3):

Q(t)=ms[cp(Tj−T0) (1−θˉ(Fo))+wc ΔhfM],Q(t) = m_s\left[c_p (T_j - T_0)\,(1 - \bar\theta(Fo)) + \frac{w_c\,\Delta h_f}{M}\right],

141 J at the capability-limited dwell and 147 J at the operating dwell, where the film is practically at jaw temperature. Per kilogram of product (0.5 kg bags) the sealing heat is 0.25–0.29 kJ/kg, two orders of magnitude below the documented energy intensity of a whole packaging step (DOE, frozen vegetables: 14 Btu/lb state of the art, 15 Btu/lb typical, i.e. 33–35 kJ/kg). The rest is machinery: jaw heaters losing heat continuously by convection and radiation, drives, vacuum and compressed air.

3. Rate-limiting step — minimum dwell and maximum cycle rate

Heat conduction problem. The two film layers form a slab of thickness 2L2L whose two faces are suddenly brought to TjT_j when the jaws close; the seal interface is the mid-plane. With ideal contact (no thermal resistance between jaw and film) and constant properties, the temperature obeys the one-dimensional heat equation ∂T/∂t=α ∂2T/∂x2\partial T/\partial t = \alpha\,\partial^2 T/\partial x^2, with the thermal diffusivity

α=kρ cp=0.19 mm2/s,\alpha = \frac{k}{\rho\,c_p} = 0.19\ \text{mm}^2/\text{s},

where kk is the thermal conductivity of the film. No open source with a quotable conductivity of polyethylene film was found, so kk is a declared scenario value (0.33 W/(m K), range 0.25–0.45). The classical separation-of-variables solution for the plane wall of half-thickness LL gives the dimensionless mid-plane temperature

θc(Fo)=Tc−TjT0−Tj=∑n=0∞4(−1)n(2n+1)π exp⁡ ⁣[−((2n+1)π2)2Fo],Fo=αtL2,\theta_c(Fo) = \frac{T_c - T_j}{T_0 - T_j} = \sum_{n=0}^{\infty} \frac{4(-1)^n}{(2n+1)\pi}\, \exp\!\left[-\left(\frac{(2n+1)\pi}{2}\right)^2 Fo\right], \qquad Fo = \frac{\alpha t}{L^2},

and the dimensionless mean temperature

θˉ(Fo)=∑n=0∞8(2n+1)2π2exp⁡ ⁣[−((2n+1)π2)2Fo].\bar\theta(Fo) = \sum_{n=0}^{\infty} \frac{8}{(2n+1)^2\pi^2} \exp\!\left[-\left(\frac{(2n+1)\pi}{2}\right)^2 Fo\right].

FoFo, the Fourier number, compares the dwell with the time heat needs to diffuse across one film layer. For Fo>0.2Fo > 0.2 the first term alone is accurate to better than 0.2%.

Minimum dwell. The seal is sound when the interface reaches TsT_s, i.e. when θc=θs=(Tj−Ts)/(Tj−T0)\theta_c = \theta_s = (T_j - T_s)/(T_j - T_0). Solving θc(Fomin)=θs\theta_c(Fo_{min}) = \theta_s (bisection on the series):

tmin=Fomin L2α.t_{min} = \frac{Fo_{min}\,L^2}{\alpha} .

With Tj=Ts+30T_j = T_s + 30 K = 150 °C, T0T_0 = 25 °C and LL = 50 µm, θs\theta_s = 0.24, FominFo_{min} = 0.676 and tmint_{min} = 9.1 ms. The dwell scales with L2L^2 and with 1/k1/k: doubling the film thickness quadruples it. The latent heat of melting is left out of the conduction problem; it slows the advance of the melt front, so tmint_{min} is a lower bound.

Capability-limited dwell. The jaw temperature fluctuates with standard deviation σTj\sigma_{T_j} and the film thickness with coefficient of variation cLc_L. A capable process holds the jaws until the interface is z σTjz\,\sigma_{T_j} above TsT_s on the thickest film of the tolerance band, L(1+zcL)L(1 + z c_L):

θc(Focap)=Tj−(Ts+zσTj)Tj−T0,tcap=Focap L2(1+zcL)2α=14.6 ms.\theta_c(Fo_{cap}) = \frac{T_j - (T_s + z\sigma_{T_j})}{T_j - T_0}, \qquad t_{cap} = \frac{Fo_{cap}\,L^2 (1 + z c_L)^2}{\alpha} = 14.6\ \text{ms}.

Indexing motion. Between two seals the film advances one bag length LpL_p and each jaw travels its stroke sjs_j open and closed. The fastest motion over a distance ss with a maximum acceleration aa is bang-bang (accelerate half-way, decelerate half-way), lasting 2s/a2\sqrt{s/a}:

tindex=2Lpaf+2×2sjaj=0.37 s.t_{index} = 2\sqrt{\frac{L_p}{a_f}} + 2 \times 2\sqrt{\frac{s_j}{a_j}} = 0.37\ \text{s}.

Cycle rates.

n˙max=1tmin+tindex=158 min−1,n˙cap=1tcap+tindex=156 min−1,n˙typ=1top+tindex=90 min−1,\dot n_{max} = \frac{1}{t_{min} + t_{index}} = 158\ \text{min}^{-1}, \qquad \dot n_{cap} = \frac{1}{t_{cap} + t_{index}} = 156\ \text{min}^{-1}, \qquad \dot n_{typ} = \frac{1}{t_{op} + t_{index}} = 90\ \text{min}^{-1},

where topt_{op} = 0.30 s is the dwell set in operation (declared scenario). Operating dwells are one to two orders of magnitude above the conduction limit of a bare film because of jaw covers, contact resistance, outer laminate layers, latent heat and the time the molten interface needs for chain interdiffusion; these are explained in the loss cascade.

4. Process capability — quality ceiling

At the capability-limited dwell the interface temperature depends on the jaw temperature and on the film thickness. A first-order propagation of their variability gives

σint2=(∂Tint∂Tj σTj)2+(∂Tint∂L cLL)2=(4.0 K)2,\sigma_{int}^2 = \left(\frac{\partial T_{int}}{\partial T_j}\,\sigma_{T_j}\right)^2 + \left(\frac{\partial T_{int}}{\partial L}\,c_L L\right)^2 = (4.0\ \text{K})^2,

with the derivatives evaluated numerically on the conduction solution. Two defects are counted:

u=Φ ⁣(Ts−Tˉintσint)(under-seal),o=Φ ⁣(Tj−(Ts+ΔTw)σTj)(over-seal),u = \Phi\!\left(\frac{T_s - \bar T_{int}}{\sigma_{int}}\right) \quad\text{(under-seal)}, \qquad o = \Phi\!\left(\frac{T_j - (T_s + \Delta T_w)}{\sigma_{T_j}}\right) \quad\text{(over-seal)},

where Tˉint\bar T_{int} is the nominal interface temperature (139 °C), ΔTw\Delta T_w the width of the sealing window above TsT_s (beyond it the film thins, shrinks or burns through) and Φ\Phi the standard normal distribution function. Then

Qmax=1−u−o.Q_{max} = 1 - u - o .

With a 3σ margin the under-seal share is about 10−610^{-6}; the quality ceiling falls when the jaw set point approaches the upper limit of the window.

5. Unavoidable stops — maximum availability

A reel lasts Lr/vL_r/v = 51 min at the capability-limited web speed v=Lp n˙capv = L_p\,\dot n_{cap} = 39 m/min. Each manual reel change stops the machine for tspt_{sp}, but an automatic zero-speed splicer removes the stop (not the splice waste), and each campaign ends with a changeover of duration tcot_{co}, a decision of the product mix. Neither stop is forced by physics or regulation, and no cleaning-in-place applies to the machine (the cleaning model is not used), so

Amax=1.A_{max} = 1 .

With the declared manual splices and changeovers,

Ascen=tcamptcamp+nrtsp+tco=0.909,A_{scen} = \frac{t_{camp}}{t_{camp} + n_r t_{sp} + t_{co}} = 0.909 ,

which enters only oee_scenario.

6. Physics-bounded OEE

Scope of the bound. The theoretical label of OEEmaxOEE_{max} means physics-bounded under the declared scenario: the ceiling follows from the physics of the operation for the declared product, equipment and schedule, and it is a bound only conditional on those declarations. It follows the common definition of all models: AmaxA_{max} counts only stops required by regulation or forced by a physical mechanism, at their physical minimum duration, plus the start-up they force; PmaxP_{max} is the ratio of the physics-limited ideal cycle to the cycle of the capable process; QmaxQ_{max} is the share of conforming units, and mass losses of conforming product are reported only as yield.

OEEmax=Amax×Pmax×Qmax,Pmax=tmin+tindextcap+tindex=0.986.OEE_{max} = A_{max} \times P_{max} \times Q_{max}, \qquad P_{max} = \frac{t_{min} + t_{index}}{t_{cap} + t_{index}} = 0.986 .

The performance ceiling compares the capability-limited cycle with the pure conduction limit: it is the price of making every seal sound. The result is OEEmaxOEE_{max} = 0.986, set by the seal capability margin; with the declared manual splices and changeovers, oee_scenario = 0.896. The capability-limited dwell and rate use declared tolerances, so they are reported without the best-available-technique label.

7. Assumptions and validity

See the assumption and validity lists generated from the configuration file. The most influential inputs (sensitivity table) are the splice and changeover durations, the reel length and the campaign length for OEE; the film thickness, conductivity and jaw-to-seal temperature difference for the dwell.

References

  • Gaur, U., Wunderlich, B. (1981). Heat capacity and other thermodynamic properties of linear macromolecules. II. Polyethylene. Journal of Physical and Chemical Reference Data, 10, 119–152. doi:10.1063/1.555636
  • U.S. Department of Energy. Bandwidth Study on Energy Use and Potential Energy Saving Opportunities in U.S. Food and Beverage Manufacturing, 2017.

7Parameter und Herkunft

Jede Eingangsgröße mit Wert, Einheit, Rolle, Unsicherheitsverteilung und Herkunft. Öffnen Sie ein Zitat, um die Quellenpassage zu lesen, die den Wert belegt.
  • wcw_c0,45

    Mass-fraction crystallinity of the polyethylene sealant film

    Szenario · Gleichverteilt 0,35 bis 0,55

    Deklarierte Annahme

    Range of low-density polyethylene films; declared assumption.

  • ρc\rho_c1,003 Mg/m³

    Density of crystalline polyethylene at 298 K

    Stoffwert · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    recalculated using eq (2) and p,. = 1.0030 Mg mHeat capacity and other thermodynamic properties of linear macromolecules. II. Polyethylene (Gaur, U.; Wunderlich, B.), Journal of Physical and Chemical Reference Data 10, 119 (1981) (öffnet in neuem Tab). American Institute of Physics for the National Institute of Standards and Technology (NIST reprint), 1981. S. 5. doi:10.1063/1.555636
  • ρa\rho_a0,8519 Mg/m³

    Density of amorphous polyethylene at 298 K

    Stoffwert · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    The amorphous density has been well established at 0.8519Heat capacity and other thermodynamic properties of linear macromolecules. II. Polyethylene (Gaur, U.; Wunderlich, B.), Journal of Physical and Chemical Reference Data 10, 119 (1981) (öffnet in neuem Tab). American Institute of Physics for the National Institute of Standards and Technology (NIST reprint), 1981. S. 4. doi:10.1063/1.555636
  • Cp,cC_{p,c}22,38 J/mol/K

    Heat capacity of crystalline polyethylene at 310 K, per mole of CH2 repeat unit (recommended data)

    Stoffwert · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    310.0 22.38 3796Heat capacity and other thermodynamic properties of linear macromolecules. II. Polyethylene (Gaur, U.; Wunderlich, B.), Journal of Physical and Chemical Reference Data 10, 119 (1981) (öffnet in neuem Tab). American Institute of Physics for the National Institute of Standards and Technology (NIST reprint), 1981. S. 30. doi:10.1063/1.555636
  • Cp,aC_{p,a}31,33 J/mol/K

    Heat capacity of amorphous polyethylene at 310 K, per mole of CH2 repeat unit (recommended data)

    Stoffwert · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    310.0 31.33 4849.Heat capacity and other thermodynamic properties of linear macromolecules. II. Polyethylene (Gaur, U.; Wunderlich, B.), Journal of Physical and Chemical Reference Data 10, 119 (1981) (öffnet in neuem Tab). American Institute of Physics for the National Institute of Standards and Technology (NIST reprint), 1981. S. 26. doi:10.1063/1.555636
  • Δhf\Delta h_f4,051 kJ/mol

    Heat of fusion of fully crystalline polyethylene at 380 K, per mole of CH2

    Stoffwert · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    380 4.051 390 4.084Heat capacity and other thermodynamic properties of linear macromolecules. II. Polyethylene (Gaur, U.; Wunderlich, B.), Journal of Physical and Chemical Reference Data 10, 119 (1981) (öffnet in neuem Tab). American Institute of Physics for the National Institute of Standards and Technology (NIST reprint), 1981. S. 32. doi:10.1063/1.555636
  • MM14,027 g/mol

    Molar mass of the CH2 repeat unit

    Stoffwert · Fest

    Berechnet

    12.011 + 2 x 1.008 g/mol (standard atomic weights).

  • kk0,33 W/m/K

    Thermal conductivity of the polyethylene film

    Szenario · Gleichverteilt 0,25 bis 0,45 W/m/K

    Deklarierte Annahme

    No open source with a quotable conductivity of polyethylene film was found; declared assumption with a wide range. It enters the dwell time inversely.

  • LL50 micrometer

    Thickness of one film layer (distance from the jaw face to the seal interface)

    Szenario · Gleichverteilt 35 bis 70 micrometer

    Deklarierte Annahme
  • cLc_L0,05

    Coefficient of variation of the film thickness

    Szenario · Gleichverteilt 0,03 bis 0,08

    Deklarierte Annahme
  • T0T_025 °C

    Initial film temperature

    Szenario · Gleichverteilt 15 bis 30 °C

    Deklarierte Annahme
  • TsT_s120 °C

    Interface temperature required for a sound seal (seal initiation temperature of the sealant)

    Szenario · Gleichverteilt 110 bis 130 °C

    Deklarierte Annahme

    Must lie above the melting range of the crystallites and below the equilibrium melting temperature of polyethylene (414.6 K); no open source with a quotable seal initiation temperature was used.

  • ΔTj\Delta T_j30 K

    Jaw set-point above the sealing temperature

    Szenario · Gleichverteilt 20 bis 40 K

    Deklarierte Annahme
  • σTj\sigma_{T_j}3 K

    Standard deviation of the jaw face temperature under control

    Szenario · Gleichverteilt 1,5 bis 4 K

    Deklarierte Annahme
  • zz3

    Capability margin in standard deviations used to set the capable dwell

    Szenario · Gleichverteilt 2,5 bis 3,5

    Deklarierte Annahme

    Operating choice, point value at the centre of the declared range 2.5-3.5; a larger margin lengthens the dwell and lowers the under-seal share.

  • ΔTw\Delta T_w60 K

    Width of the sealing window above the sealing temperature (beyond it the film thins

    Szenario · Gleichverteilt 50 bis 70 K

    Deklarierte Annahme
  • topt_{op}0,3 s

    Jaw dwell time set in operation (jaw covers, contact resistance and laminate layers lengthen it)

    Szenario · Gleichverteilt 0,15 bis 0,6 s

    Deklarierte Annahme

    No open source with documented dwell times was used; declared assumption.

  • LpL_p0,25 m

    Film length per bag (index length)

    Szenario · Fest

    Deklarierte Annahme
  • WW0,15 m

    Flat width of the bag (length of the cross seal)

    Szenario · Fest

    Deklarierte Annahme
  • hjh_j0,012 m

    Height of the cross-seal jaws (top seal of one bag plus bottom seal of the next)

    Szenario · Fest

    Deklarierte Annahme
  • wfw_f0,01 m

    Width of the longitudinal fin seal

    Szenario · Fest

    Deklarierte Annahme
  • mpm_p0,5 kg

    Mass of product per bag

    Szenario · Fest

    Deklarierte Annahme
  • afa_f20 m/s²

    Maximum acceleration of the film transport (limited by film tension and slip of the pull belts)

    Szenario · Gleichverteilt 10 bis 40 m/s²

    Deklarierte Annahme
  • sjs_j0,04 m

    Opening stroke of each jaw

    Szenario · Fest

    Deklarierte Annahme
  • aja_j30 m/s²

    Maximum acceleration of the jaw carriage

    Szenario · Gleichverteilt 15 bis 50 m/s²

    Deklarierte Annahme
  • LrL_r2.000 m

    Film length on one reel

    Szenario · Gleichverteilt 1.000 bis 4.000 m

    Deklarierte Annahme
  • LwL_w3 m

    Film wasted at each reel splice

    Szenario · Gleichverteilt 1 bis 6 m

    Deklarierte Annahme
  • tspt_{sp}3 min

    Machine stop per manual reel change and splice (zero with an automatic zero-speed splicer)

    Szenario · Gleichverteilt 1 bis 6 min

    Deklarierte Annahme
  • tcampt_{camp}8 h

    Production time between two format or product changeovers

    Szenario · Gleichverteilt 4 bis 24 h

    Deklarierte Annahme
  • tcot_{co}20 min

    Duration of a changeover

    Szenario · Gleichverteilt 10 bis 45 min

    Deklarierte Annahme
  • nsun_{su}20

    Bags wasted while the machine stabilises after a changeover

    Szenario · Gleichverteilt 5 bis 50

    Deklarierte Annahme

8Vergleichswerte

Dokumentierte Werte aus offenen Quellen zur Prüfung der Obergrenzen; kein dokumentierter Wert darf die theoretische Grenze übertreffen.
VergleichswertObergrenzeWertHerkunft
DOE bandwidth study, thermodynamic minimum energy intensity of packaging of frozen vegetables
Wörtliches Zitat anzeigen
Freezing -53.5 to 586 279 279 -48.6 12.1 5.8 5.8 -1.02 Packaging 15 14 14 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (öffnet in neuem Tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. S. 56. DOE/EE-1571; OSTI ID 1512366
Theoretisch0 Btu/lbVerifiziertes Zitat
DOE bandwidth study, state-of-the-art on-site energy intensity of packaging of frozen vegetables, per lb of product (whole packaging step; the theoretical output of this model is per pack, compare with heat_min_seal_per_kg)
Wörtliches Zitat anzeigen
Freezing -53.5 to 586 279 279 -48.6 12.1 5.8 5.8 -1.02 Packaging 15 14 14 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (öffnet in neuem Tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. S. 56. DOE/EE-1571; OSTI ID 1512366
Beste verfügbare Technik14 Btu/lbVerifiziertes Zitat
DOE bandwidth study, current typical on-site energy intensity of packaging of frozen vegetables, per lb of product (whole packaging step; the theoretical output of this model is per pack, compare with heat_typical_per_kg)
Wörtliches Zitat anzeigen
Freezing -53.5 to 586 279 279 -48.6 12.1 5.8 5.8 -1.02 Packaging 15 14 14 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (öffnet in neuem Tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. S. 56. DOE/EE-1571; OSTI ID 1512366
Typisch15 Btu/lbVerifiziertes Zitat

9Unvermeidbare Stillstände

Stillstände, die Physik oder Regulierung erzwingen; sie bestimmen die maximale Verfügbarkeit.
  • Reel change and splice (scenario stop with a manual splicer: availability_scenario only)Deklarierte Annahme

    A reel holds a finite film length; at the web speed of the machine it runs out after L_r / v. A manual splice stops the machine for t_sp; an automatic zero-speed splicer removes the stop but not the splice waste.

  • Format or product changeover (scenario stop: availability_scenario only)Deklarierte Annahme

    Change of bag size, film or product requires stopping, adjusting forming set and jaws, and restarting with start-up waste. Declared scenario values.

10Annahmen

  1. No stop is forced by physics or regulation: an automatic zero-speed splicer removes the reel-change stop (the splice waste remains in the film yield) and changeovers follow the product mix, so availability_max = 1 and both stops enter only availability_scenario and oee_scenario. No cleaning-in-place applies to a form-fill-seal machine, so the cleaning model is not used. Dwell and rate with the capability margin use declared tolerances and are reported without the bat label.
  2. One-dimensional transient conduction through two identical film layers between two jaws at the same constant temperature (symmetric plane wall with fixed surface temperature, ideal contact).
  3. Constant properties evaluated near room temperature; the latent heat of fusion is not included in the conduction problem, which makes the computed dwell a lower bound, and it is included in the energy balance.
  4. A seal is sound when the interface reaches the sealing temperature during the dwell; under-seals and over-seals are the only quality losses (contamination of the seal area by product is not modelled).
  5. Film and jaw carriage move with bang-bang (triangular velocity) profiles at their maximum acceleration; the longitudinal seal does not limit the rate.
  6. Film yield counts splice and start-up waste only; trim does not exist in a fin-sealed pillow bag.

11Gültigkeitsbereich

  • Polyolefin sealant films sealed with constant-temperature (hot) jaws on both sides; impulse and ultrasonic sealing are outside the model.
  • Sealing temperatures below the equilibrium melting temperature of polyethylene (414.6 K) and film thicknesses of 20 to 100 micrometres per layer.

12Sensitivität

Elastizität: relative Änderung der Ergebnisgröße bei relativer Änderung jedes Parameters. Daneben steht die Spearman-Rangkorrelation aus den Monte-Carlo-Ziehungen.
  • LLThickness of one film layer (distance from the jaw face to the seal interface)
    Elastizität -0,028Spearman-ρ -0,72
  • zzCapability margin in standard deviations used to set the capable dwell
    Elastizität -0,018Spearman-ρ -0,21
  • MMMolar mass of the CH2 repeat unit
    Elastizität +0,014Spearman-ρ —
  • kkThermal conductivity of the polyethylene film
    Elastizität +0,014Spearman-ρ +0,29
  • ΔTj\Delta T_jJaw set-point above the sealing temperature
    Elastizität +0,011Spearman-ρ +0,28
  • cLc_LCoefficient of variation of the film thickness
    Elastizität -0,010Spearman-ρ -0,36
  • Cp,aC_{p,a}Heat capacity of amorphous polyethylene at 310 K, per mole of CH2 repeat unit (recommended data)
    Elastizität -0,009Spearman-ρ —
  • ρa\rho_aDensity of amorphous polyethylene at 298 K
    Elastizität -0,008Spearman-ρ —
  • σTj\sigma_{T_j}Standard deviation of the jaw face temperature under control
    Elastizität -0,008Spearman-ρ -0,24
  • ρc\rho_cDensity of crystalline polyethylene at 298 K
    Elastizität -0,006Spearman-ρ —
  • Cp,cC_{p,c}Heat capacity of crystalline polyethylene at 310 K, per mole of CH2 repeat unit (recommended data)
    Elastizität -0,005Spearman-ρ —
  • LpL_pFilm length per bag (index length)
    Elastizität +0,004Spearman-ρ —
  • afa_fMaximum acceleration of the film transport (limited by film tension and slip of the pull belts)
    Elastizität -0,004Spearman-ρ -0,19
  • TsT_sInterface temperature required for a sound seal (seal initiation temperature of the sealant)
    Elastizität -0,004Spearman-ρ -0,03
  • aja_jMaximum acceleration of the jaw carriage
    Elastizität -0,003Spearman-ρ -0,13
  • sjs_jOpening stroke of each jaw
    Elastizität +0,003Spearman-ρ —
  • wcw_cMass-fraction crystallinity of the polyethylene sealant film
    Elastizität +0,001Spearman-ρ +0,01
  • T0T_0Initial film temperature
    Elastizität +0,001Spearman-ρ +0,02
  • Größe steigt mit dem Parameter
  • Größe sinkt mit dem Parameter

13Validierungsprüfungen

Ein Modell wird nur veröffentlicht, wenn alle Prüfungen bestanden sind.
  • Dimensionsanalyse31 outputs converted to their declared unitsBestanden
  • Jeder zitierte Wert an seiner Quelle verifiziert8 verified, 0 failedBestanden
  • Kein dokumentierter Wert übertrifft die theoretische GrenzeBestanden
  • Obergrenzen in physikalischer ReihenfolgeBestanden
  • Anteile zwischen 0 und 1Bestanden

14Verlustursachen in dieser Operation

Wahrscheinlichkeit, dass jede Ursache als relevanter Verlust einer Linie dokumentiert ist, gepoolt über alle Segmente.

15Literatur

  1. Heat capacity and other thermodynamic properties of linear macromolecules. II. Polyethylene (Gaur, U.; Wunderlich, B.), Journal of Physical and Chemical Reference Data 10, 119 (1981) (öffnet in neuem Tab). American Institute of Physics for the National Institute of Standards and Technology (NIST reprint), 1981. S. 5. doi:10.1063/1.555636
  2. Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (öffnet in neuem Tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. S. 56. DOE/EE-1571; OSTI ID 1512366
  3. doi:10.1063/1.555636 — Heat capacity, heat of fusion and densities of polyethylene.