Startup yield loss in forming (blow moulding)
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei weniger als 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 47 % der Verlustzeit der Linie. Berichtet von 0 der 76 Studien, die sie beobachten konnten (spärliche Evidenz).
Was passiert
After a stop or at the beginning of a run, the forming (blow moulding) machine needs time to reach stable mould temperature, air pressure and cycle timing; preforms or containers produced before these parameters stabilize are undersized, deformed, have thin walls or incomplete forming and are rejected. The loss accumulates as scrap units generated during the warm-up window rather than as downtime.
Was man dagegen tut
Define and monitor a startup ramp-up procedure with process-variable interlocks (mould temperature, air pressure) that hold the machine in a non-saleable or purge mode until setpoints are reached, and track startup scrap separately to shorten warm-up time through preheating or standby conditioning.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,4 % [0,0–1,3 %]
- Erwarteter Anteil an der Verlustzeit
- 0,2 % [0,0–0,6 %]
- Anteil an der Verlustzeit bei Auftreten
- 47 % [28–67 %]
- Studien / Einheiten
- 76 / 96
- Evidenzgrad
- D
Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,5 % [0,0–1,9 %]5 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte0,4 % [0,0–1,7 %]11 Studien
- Bier, Wein und Spirituosen0,5 % [0,0–2,0 %]0 Studien
- Backwaren und Teigwaren0,4 % [0,0–1,7 %]25 Studien
- Fleisch, Geflügel und Fisch0,5 % [0,0–2,0 %]3 Studien
- Obst- und Gemüseverarbeitung0,5 % [0,0–2,0 %]3 Studien
- Getreide- und Ölsaatenmüllerei0,5 % [0,0–1,9 %]0 Studien
- Zucker und Süßwaren0,4 % [0,0–1,8 %]8 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel0,4 % [0,0–1,8 %]7 Studien
- Futtermittel und Heimtiernahrung0,4 % [0,0–1,8 %]6 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)0,5 % [0,0–1,9 %]8 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseAfter a stop or at the beginning of a run, the forming (blow moulding) machine needs time to reach stable mould temperature, air pressure and cycle timing; preforms or containers produced before these parameters stabilize are undersized, deformed, have thin walls or incomplete forming and are rejected. The loss accumulates as scrap units generated during the warm-up window rather than as downtime.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseSCADA/MES shows the forming machine running (machine state = production) immediately after a startup or format change while reject/quality counters spike and first-pass yield is depressed for a limited number of cycles; mould and air temperature/pressure trends are still ramping toward setpoint during this window, and the condition clears once process variables stabilize within band.
Gegenmaßnahme
Ingenieurpraktische HinweiseDefine and monitor a startup ramp-up procedure with process-variable interlocks (mould temperature, air pressure) that hold the machine in a non-saleable or purge mode until setpoints are reached, and track startup scrap separately to shorten warm-up time through preheating or standby conditioning.
4Quellen
- Analisis Total Productive Maintenance (TPM) dengan Menggunakan Metode Overall Equipment Effectiveness (OEE) pada Mesin Blowing (2025)Quelle öffnenAnteil an der Verlustzeit: 0 % · laut Bericht: “Reduce Yield”
Wörtliches Zitat anzeigen
Rata - rata 6,10 0,95 11,47 0,00 0,00 0,21

