foratvise
Loslegen
Anlagenausfall (Störungen)

Gripper/clamp breakage

Anlagenausfall (Störungen)VerfügbarkeitFormen, Gießen und Dosieren

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei etwa 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 57 % der Verlustzeit der Linie. Berichtet von 1 der 76 Studien, die sie beobachten konnten (spärliche Evidenz).

Was passiert

The mechanical grippers or clamps that hold and transfer the material or mould during the forming cycle accumulate fatigue from repeated clamping, impact and thermal cycles until a component fractures or deforms beyond function. The break can occur in the gripper jaw, pivot pin, spring or actuating linkage, causing the forming station to lose its grip on the part.

Was man dagegen tut

Apply preventive maintenance with periodic inspection and replacement of gripper components based on cycle counts, use wear-resistant materials or hardened pins and jaws, and monitor clamping force or stroke to detect early degradation before fracture occurs.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
0,7 % [0,1–2,1 %]
Erwarteter Anteil an der Verlustzeit
0,4 % [0,1–1,2 %]
Anteil an der Verlustzeit bei Auftreten
57 % [46–67 %]
Studien / Einheiten
76 / 96
Evidenzgrad
D

Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    0,9 % [0,1–3,2 %]5 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    1,1 % [0,1–4,1 %]11 Studien
  • Bier, Wein und Spirituosen
    0,9 % [0,1–3,5 %]0 Studien
  • Backwaren und Teigwaren
    0,7 % [0,1–2,4 %]25 Studien
  • Fleisch, Geflügel und Fisch
    0,9 % [0,1–3,5 %]3 Studien
  • Obst- und Gemüseverarbeitung
    0,9 % [0,1–3,4 %]3 Studien
  • Getreide- und Ölsaatenmüllerei
    0,9 % [0,1–3,3 %]0 Studien
  • Zucker und Süßwaren
    0,8 % [0,1–3,1 %]8 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    0,8 % [0,1–3,0 %]7 Studien
  • Futtermittel und Heimtiernahrung
    0,9 % [0,1–3,1 %]6 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    0,9 % [0,1–3,2 %]8 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

The mechanical grippers or clamps that hold and transfer the material or mould during the forming cycle accumulate fatigue from repeated clamping, impact and thermal cycles until a component fractures or deforms beyond function. The break can occur in the gripper jaw, pivot pin, spring or actuating linkage, causing the forming station to lose its grip on the part.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

The SCADA/MES logs an equipment fault alarm or station-stopped state tied to the gripper axis or clamp mechanism, often with a mechanical fault code rather than a sensor fault, followed by an extended downtime state until maintenance replaces the part. Upstream and downstream stations may show starvation or blocking while the forming unit is offline.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Apply preventive maintenance with periodic inspection and replacement of gripper components based on cycle counts, use wear-resistant materials or hardened pins and jaws, and monitor clamping force or stroke to detect early degradation before fracture occurs.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Anteil an den Verlustereignissen: 19,0 % · laut Bericht: “Quebra das pinças”
    Wörtliches Zitat anzeigen
    Quebra das pinças. Esta causa não foi validada, pois representava apenas de 19 % das ocorrências, já que todo o processo de montagem das caixas e sacos são automáticos.