Laser Marking Machine Speed Loss
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 63 % der Verlustzeit der Linie. Berichtet von 1 der 85 Studien, die sie beobachten konnten (spärliche Evidenz).
Was passiert
The laser marking machine runs below its rated throughput because the beam power, optics focus or marking parameters have drifted, forcing the control system or the operator to slow the marking pass to keep the code legible and durable on the substrate. Substrate variability (surface finish, curvature, material batch) can also require a lower effective speed to avoid incomplete or unreadable codes.
Was man dagegen tut
Apply a preventive maintenance routine on the laser source and optics, including cleaning, alignment checks and power verification, and standardize marking parameters by substrate and product type. Introduce real-time mark-quality feedback so that speed is only reduced when strictly necessary and restored automatically once conditions normalize.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,8 % [0,2–2,3 %]
- Erwarteter Anteil an der Verlustzeit
- 0,5 % [0,1–1,5 %]
- Anteil an der Verlustzeit bei Auftreten
- 63 % [49–75 %]
- Studien / Einheiten
- 85 / 113
- Evidenzgrad
- D
Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,9 % [0,1–3,3 %]11 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte0,8 % [0,1–2,6 %]29 Studien
- Bier, Wein und Spirituosen0,9 % [0,1–3,1 %]13 Studien
- Backwaren und Teigwaren1,5 % [0,1–5,9 %]1 Studie
- Fleisch, Geflügel und Fisch1,0 % [0,1–3,7 %]4 Studien
- Obst- und Gemüseverarbeitung1,0 % [0,1–3,7 %]4 Studien
- Getreide- und Ölsaatenmüllerei1,0 % [0,1–3,5 %]3 Studien
- Zucker und Süßwaren1,0 % [0,1–3,7 %]3 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel0,9 % [0,1–3,5 %]4 Studien
- Futtermittel und Heimtiernahrung1,0 % [0,1–3,7 %]4 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)0,9 % [0,1–3,4 %]9 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseThe laser marking machine runs below its rated throughput because the beam power, optics focus or marking parameters have drifted, forcing the control system or the operator to slow the marking pass to keep the code legible and durable on the substrate. Substrate variability (surface finish, curvature, material batch) can also require a lower effective speed to avoid incomplete or unreadable codes.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseMES/SCADA shows the marker in a running state but with actual cycle time or throughput persistently above the nominal value, depressing the OEE performance factor without any associated fault or stop alarm. Logs may show repeated manual speed overrides, reduced line speed setpoints, or laser power/focus parameters outside their normal operating band.
Gegenmaßnahme
Ingenieurpraktische HinweiseApply a preventive maintenance routine on the laser source and optics, including cleaning, alignment checks and power verification, and standardize marking parameters by substrate and product type. Introduce real-time mark-quality feedback so that speed is only reduced when strictly necessary and restored automatically once conditions normalize.
4Quellen
- Mitigating operational risks and enhancing machine performance through total productive maintenance and OEE: a case study on packaging equipment (2025)Quelle öffnenAnteil an der Verlustzeit: 38,0 % · laut Bericht: “performance losses”
Wörtliches Zitat anzeigen
The analysis of the six significant losses reveals that performance losses are the dominant contributor to overall equipment inefficiency, accounting for 38% of the total OEE loss.

