foratvise
Loslegen
Abfüll- und Verpackungslinie

Etikettieren und Kennzeichnen

Roll-fed wrap-around labelling of cylindrical containers with hot-melt glue

Validiertes ModellOEE-Grenze 1,000 [0,775–1,000]20.000 Monte-Carlo-Stichproben · Seed 20261115 · berechnet am 16. November 2026

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Etikettieren und Kennzeichnen kann höchstens 100 von je 100 geplanten Stunden nutzen. Der Rest entfällt auf Grenzen, die kein Werk vermeiden kann.

  1. 100höchstens nutzbar

Die drei Grenzen, die das festlegen

Laufzeit: bis 100 %

Der Rest sind Stillstände, die Physik oder Vorschrift erzwingen: Reinigung, Umrüsten, Abtauen.

Geschwindigkeit: bis 100 %

Wie nah an ihrer Höchstgeschwindigkeit sie laufen kann, ohne Produkt oder Anlage zu schädigen.

Gutprodukt: bis 100 %

Ein Teil des Produkts liegt auch bei gut beherrschtem Prozess außerhalb der Spezifikation.

Das technische Detail ansehen

Technisches Detail

Unsicherheitsintervalle, physikalische Modelle je Station und Quellen, für alle, die jede Zahl prüfen möchten.

1Szenario

Filled and capped 0.5 L PET bottles of a carbonated soft drink are labelled downstream of the filler on a rotary roll-fed labeller. The label web is drawn from a reel, each label is cut to length at the print mark, receives hot-melt glue on its leading and trailing edges and is wrapped once around the cylindrical label panel of the rotating container; the trailing edge is glued over the leading edge. The same geometry describes wrap-around paper labels on cans of vegetables. The physics-limited quantities are the overlap of the glue seam (geometry and cutting registration) and the web speed at which the registration still keeps the seam capable. The labeller runs faster than the filler (the V-graph of a bottling line); its documented set performance and failure behaviour come from measurements in an industrial bottling plant.

Herkunft der EingangsgrößenDeklarierte Annahme21Verifiziertes Zitat5

2Ergebnisse

Punktwert aus den Nominalparametern und 95-%-Intervall aus 20.000 Monte-Carlo-Ziehungen der unsicheren Parameter.
  • Cut length of the label (panel circumference plus nominal overlap)212 [203–221] mm
  • Standard deviation of the overlap at standstill registration (cutting and container diameter only)0,434 [0,295–0,580] mm
  • Largest web speed at which the overlap stays z standard deviations above its minimum3,00 [2,04–3,93] m/s
  • Standard deviation of the overlap at the capable web speed0,741 [0,419–1,332] mm
  • Share of labels whose overlap is shorter than the minimum glue seam6,20 × 10⁻¹⁰ [6,25 × 10⁻³⁰–4,39 × 10⁻⁴]
  • Share of labels placed outside the vertical tolerance of the label panel5,73 × 10⁻⁷ [1,44 × 10⁻¹⁶–1,79 × 10⁻²]
  • TheoretischMaximum OEE quality factor (overlap seam and placement) at the capable web speed1,000 [0,982–1,000]
  • Quality factor if the labeller ran at its maximum web speed regardless of registration capability1,000 [0,982–1,000]
  • Containers per hour at the maximum web speed of the declared machine50.895 [34.701–67.675] 1/h
  • Containers per hour at the capable web speed50.895 [34.561–67.168] 1/h
  • Best dokumentiertSet performance of a labelling machine measured in an industrial bottling plant33.197 1/h
  • TheoretischThermodynamic minimum energy per label (the glue returns to ambient)0 J
  • Heat to bring the glue of one label to the application temperature, without recovery5,70 [3,38–14,39] J
  • Glue heating duty per kg of labelled product0,0110 [0,0065–0,0277] kJ/kg
  • Run time of one label reel at the capable rate22,2 [10,6–41,8] min
  • TheoretischMaximum label-material yield (splice and start-up waste)0,9994 [0,9980–0,9997]
  • TheoretischMaximum availability (no stop is forced by physics or regulation: reel changes are removable by an automatic splicer)1,00
  • Best dokumentiertAvailability of a labelling machine from its measured MTBF and MTTR0,973
  • Availability with declared manual reel splices0,881 [0,705–0,960]
  • TheoretischPerformance factor: capable web speed over maximum web speed1,00 [0,78–1,00]
  • TheoretischPhysics-bounded OEE1,000 [0,775–1,000]
  • OEE with declared manual reel splices0,881 [0,643–0,958]

3Obergrenzen je Dimension

Jede Dimension zeigt die vom Modell berechneten Obergrenzen und, bei vergleichbaren Einheiten, dokumentierte Vergleichswerte. Farbe und Markerform kennzeichnen den Grenztyp im gesamten Orakel.
  • Theoretisch
  • Beste verfügbare Technik
  • Best dokumentiert
  • Typisch
Qualitäthöher ist besser
  • TheoretischMaximum OEE quality factor (overlap seam and placement) at the capable web speed1,000 [0,982–1,000]
Durchsatz1/h · höher ist besser
  • Best dokumentiertSet performance of a labelling machine measured in an industrial bottling plant33.197 1/h
Energie je ProdukteinheitJ · niedriger ist besser
  • TheoretischThermodynamic minimum energy per label (the glue returns to ambient)0 J
Ausbeutehöher ist besser
  • TheoretischMaximum label-material yield (splice and start-up waste)0,9994 [0,9980–0,9997]
Verfügbarkeithöher ist besser
  • TheoretischMaximum availability (no stop is forced by physics or regulation: reel changes are removable by an automatic splicer)1,00
  • Best dokumentiertAvailability of a labelling machine from its measured MTBF and MTTR0,973
Leistunghöher ist besser
  • TheoretischPerformance factor: capable web speed over maximum web speed1,00 [0,78–1,00]
OEEhöher ist besser
  • TheoretischPhysics-bounded OEE1,000 [0,775–1,000]

4Verlustkaskade

Was jede Obergrenze von der nächsten trennt, von der physikalischen Grenze bis zum typischen Betrieb.
  1. TheoretischBest dokumentiertVerfügbarkeit
    1,00 → 0,973 (Abstand 0,0273)

    No stop of a roll-fed labeller is forced by physics or by regulation: the reel change is removable by an automatic splicer and there is no hygienic cleaning duty on the label path, so the availability ceiling is 1. The documented labeller of an industrial bottling plant stopped on average every 1 423 s for 40 s, an availability of 97.3 %. Such short, frequent stops are typical of container handling: containers that jam in the infeed star wheel or the centring bells, labels that fail to transfer from the vacuum or glue pallet, glue that strings or chars, and sensor faults at the print mark. Each of these is a mechanical or control loss, not a physical limit; in a line, an accumulation conveyor between filler and labeller absorbs most of them (see the conveying model).

  2. TheoretischTypischEnergie je Produkteinheit

    The glue is heated and cools back to ambient on the container, so with ideal heat recovery no net energy would be needed: the thermodynamic minimum is zero. Without recovery the least heat is that of bringing the few tens of milligrams of glue per label to the application temperature, a few joules per label and a few thousandths of a kilojoule per kilogram of product. A real glue station keeps a melt tank, hoses and a glue roller at temperature all the time and loses heat continuously to the room, and the drives of the turret, the vacuum drum and the conveyors dominate the electricity of the machine; the energy of labelling is set by machinery, not by the physics of the label.

5Physikalisch begrenzte OEE

Die höchste OEE, die die Operation erreichen kann: Verfügbarkeit, Leistung und Qualität, begrenzt nur durch unvermeidbare Stillstände und physikalische Prozessfähigkeit.
Anteil der Belegungszeit, der nach jedem unvermeidbaren Verlust verbleibt. Die Achse beginnt bei 0,70.
  • Belegungszeit (ideal)
    1,000
  • Verfügbarkeit
    Faktor 1,00
    1,000 (−0,000)
  • Leistung
    Faktor 1,00 [0,78–1,00]
    1,000 (−0,000)
  • Qualität
    Faktor 1,000 [0,982–1,000]
    1,000 (−0,000)
  • Physikalisch begrenzte OEE
    1,000 [0,775–1,000]

6Vollständige Herleitung

Massen- und Energiebilanzen, geschwindigkeitsbestimmender Schritt, Prozessfähigkeit und unvermeidbare Stillstände, mit Erläuterung jedes Terms.

Scope. Filled and capped 0.5 L PET bottles of a carbonated soft drink are labelled downstream of the filler on a rotary roll-fed labeller. Each label is cut from the web at its print mark, receives hot-melt glue on its leading and trailing edges and is wrapped once around the cylindrical label panel of the rotating bottle; the trailing edge is glued over the leading edge. The same geometry describes wrap-around paper labels on cans of vegetables. The labeller runs faster than the filler (the V-graph of a bottling line). Symbols and their values, units, uncertainty distributions and sources are listed in the parameter table generated from config/physics/labeling.yaml. Numbers quoted here are point values; the output table gives the Monte Carlo intervals.

1. Mass balance — maximum label-material yield

Labelling consumes no product. Label web is lost at each reel splice (a length LwL_w around the splice) and at each changeover while the cut registration settles (nsun_{su} labels). During a campaign of duration tcampt_{camp} at the capable rate n˙cap\dot n_{cap} the web used for good labels is Lcamp=n˙cap tcamp LL_{camp} = \dot n_{cap}\,t_{camp}\,L, the number of reels is nr=Lcamp/Lrn_r = L_{camp}/L_r, and

Ymax=LcampLcamp+nrLw+nsuL=0.9994,Y_{max} = \frac{L_{camp}}{L_{camp} + n_r L_w + n_{su} L} = 0.9994,

where LL is the cut length of one label. A container rejected for a bad label is counted as a quality loss (section 4), not as a yield loss: the product and the container are not consumed by the labeller.

2. Energy balance — minimum energy per label

The glue is melted, applied and cools back to ambient on the container; the label and the container end in their initial thermal state. In the reversible limit all the heat could be recovered, so the thermodynamic minimum is zero. Without recovery the least heat is that of bringing the glue mass mgm_g of one label from ambient T0T_0 to the application temperature TgT_g:

Qglue=mg cp,g (Tg−T0)=5.7 J per label,Q_{glue} = m_g\,c_{p,g}\,(T_g - T_0) = 5.7\ \text{J per label},

0.011 kJ per kg of product. Glue mass, specific heat and temperature are declared scenario values. A real glue station keeps a melt tank, hoses and a glue roller hot all the time and loses heat continuously; the turret, vacuum drum and conveyor drives dominate the electricity of the machine.

3. Rate-limiting step — web speed and registration

Label length. A label wraps the panel of diameter DD once and overlaps itself by the nominal overlap ono_n:

L=πD+on=212.2 mm.L = \pi D + o_n = 212.2\ \text{mm}.

Rate. The web feeds one label length per container, so the rate at web speed vv is n˙=v/L\dot n = v/L: 50 900 containers per hour at the maximum web speed of the declared machine, vmaxv_{max} = 3 m/s. The web speed is a machine design value without an open source, so the rates carry no theoretical label (assumption a3).

Registration error grows with speed. The cut is triggered at the print mark. A timing error δt\delta t of mark detection and cut actuation becomes a length error v δtv\,\delta t, so the standard deviation of the cut length is

σL(v)2=σL,02+(v σt)2,\sigma_L(v)^2 = \sigma_{L,0}^2 + (v\,\sigma_t)^2,

where σL,0\sigma_{L,0} is the error of the cutting mechanism at standstill registration and σt\sigma_t the timing jitter. The faster the web, the wider the scatter of the overlap; this is the physical trade-off between speed and quality of the operation.

Capable web speed. The realised overlap is o=Lcut−πDco = L_{cut} - \pi D_c (section 4); with independent cut length and container diameter its standard deviation is

σo(v)=σL(v)2+(πσD)2.\sigma_o(v) = \sqrt{\sigma_L(v)^2 + (\pi\sigma_D)^2}.

A capable process keeps the mean overlap zz standard deviations above the minimum glue seam omino_{min}, i.e. σo(v)≤(on−omin)/z\sigma_o(v) \le (o_n - o_{min})/z. The largest capable web speed is

vcap=min⁡ ⁣(vmax, 1σt(on−ominz)2−σL,02−(πσD)2).v_{cap} = \min\!\left(v_{max},\ \frac{1}{\sigma_t}\sqrt{\left(\frac{o_n - o_{min}}{z}\right)^2 - \sigma_{L,0}^2 - (\pi\sigma_D)^2}\right).

With the declared values the registration limit is 6.0 m/s, above the machine's 3 m/s, so vcap=vmaxv_{cap} = v_{max}; when the jitter is large (upper part of its range) the capable speed falls below the maximum and the performance factor drops below 1.

4. Process capability — quality ceiling

Overlap seam. The trailing-edge glue bead must land on the label itself; if the overlap is shorter than omino_{min} the seam carries only part of the bead and the label opens or flags. With o∼N(on,σo2)o \sim \mathcal N(o_n, \sigma_o^2) the share of short seams is

u=Φ ⁣(omin−onσo(vcap))=6×10−10,u = \Phi\!\left(\frac{o_{min} - o_n}{\sigma_o(v_{cap})}\right) = 6\times10^{-10},

with σo(vcap)\sigma_o(v_{cap}) = 0.74 mm and Φ\Phi the standard normal distribution function.

Vertical placement. The label must stay within ±Δv\pm\Delta_v of its nominal height on the panel; with a vertical position error e∼N(0,σv2)e \sim \mathcal N(0, \sigma_v^2) the misplaced share is m=2 Φ(−Δv/σv)=5.7×10−7m = 2\,\Phi(-\Delta_v/\sigma_v) = 5.7\times10^{-7}.

Qmax=(1−u)(1−m)=0.999999.Q_{max} = (1 - u)(1 - m) = 0.999999 .

Running at the maximum web speed regardless of registration capability gives quality_at_max_speed, which equals QmaxQ_{max} here because the declared machine is capable at full speed. Wrinkles, flags caused by the glue, print defects and code legibility are not modelled, so QmaxQ_{max} is an upper bound. No open source quotes the minimum glue overlap, the cutting accuracy, the timing jitter or the placement tolerance of roll-fed labellers; they are declared scenario values with ranges, and the Monte Carlo interval of QmaxQ_{max} reflects them.

5. Unavoidable stops — maximum availability

A reel holds a finite web length and runs out after Lr/(n˙capL)L_r/(\dot n_{cap} L) = 22 minutes at the capable rate. A manual splice stops the labeller, but an automatic splicer removes the stop (not the splice waste); no cleaning-in-place applies to the label path, so the cleaning model is not used. No stop is forced by physics or regulation:

Amax=1.A_{max} = 1 .

With manual splices of duration tspt_{sp},

Ascen=tcamptcamp+nr tsp=0.881,A_{scen} = \frac{t_{camp}}{t_{camp} + n_r\,t_{sp}} = 0.881,

which enters only oee_scenario.

Documented availability. In an industrial bottling plant (mineral water and soft drinks, returnable glass bottles), the labelling machine was measured at a set performance of 33 197 bottles per hour with a mean time between failures of 1 423 s and a mean time to repair of 40 s (Bär et al., 2021, Table A1). With the availability defined in the same source as A=MTBF/(MTBF+MTTR)A = MTBF/(MTBF + MTTR),

Adoc=14231423+40=0.9727,A_{doc} = \frac{1423}{1423 + 40} = 0.9727,

the 97.3 % of the source table. These short, frequent stops (jams in the star wheels, failed label transfers, glue and sensor faults) are mechanical and control losses, not physical limits; the conveying model shows how much of them an accumulation buffer keeps away from the filler.

6. Physics-bounded OEE

Scope of the bound. The theoretical label of OEEmaxOEE_{max} means physics-bounded under the declared scenario: the ceiling follows from the geometry and registration physics of the operation for the declared container, label and machine, and it is a bound only conditional on those declarations. It follows the common definition of all models: AmaxA_{max} counts only stops required by regulation or forced by a physical mechanism; PmaxP_{max} is the ratio of the physics-limited ideal cycle to the cycle of the capable process; QmaxQ_{max} is the share of conforming units, and mass losses of conforming material are reported only as yield.

OEEmax=Amax×Pmax×Qmax,Pmax=vcapvmax=1,OEEmax=0.999999.OEE_{max} = A_{max} \times P_{max} \times Q_{max}, \qquad P_{max} = \frac{v_{cap}}{v_{max}} = 1, \qquad OEE_{max} = 0.999999 .

The labeller does not bound the line by physics: its ceiling is set by the registration capability, which the declared machine meets at full speed. With the declared manual splices oee_scenario = 0.881; the documented failure behaviour of a real labeller gives an availability of 0.973.

Consistency with the other models. The labeller runs faster than the filler, so in a line it never sets the rate; its documented set performance (33 197 per hour against 28 998 per hour of the filler of the same plant, a table cell the filler shares with the empty bottle inspector) is the V-graph used in the conveying model. Filling, closing and the product are outside this model.

7. Assumptions and validity

See the assumption and validity lists generated from the configuration file. The most influential inputs (sensitivity table) are the timing jitter, the maximum web speed and the overlap margin for performance, the vertical placement dispersion for quality, and the reel length and splice time for the scenario availability.

References

  • Bär, R. M., Zeilmann, M., Nophut, C., Kleinert, J., Beyer, K., Voigt, T. (2021). Simulation of energy and media demand of beverage bottling plants by automatic model generation. Sustainability, 13, 10089. doi:10.3390/su131810089

7Parameter und Herkunft

Jede Eingangsgröße mit Wert, Einheit, Rolle, Unsicherheitsverteilung und Herkunft. Öffnen Sie ein Zitat, um die Quellenpassage zu lesen, die den Wert belegt.
  • DD65 mm

    Diameter of the cylindrical label panel of the container

    Szenario · Gleichverteilt 62 bis 68 mm

    Deklarierte Annahme

    0.5 L PET bottle; no open bottle drawing was used. Declared assumption.

  • σD\sigma_D0,1 mm

    Standard deviation of the label-panel diameter from container to container

    Szenario · Gleichverteilt 0,05 bis 0,15 mm

    Deklarierte Annahme
  • ono_n8 mm

    Nominal overlap of the trailing edge over the leading edge (label design)

    Szenario · Gleichverteilt 7 bis 9 mm

    Deklarierte Annahme
  • omino_{min}3,5 mm

    Least overlap that still carries the full glue bead of the seam

    Szenario · Gleichverteilt 3 bis 4 mm

    Deklarierte Annahme

    No open source states the minimum glue-seam overlap; declared assumption.

  • σL,0\sigma_{L,0}0,3 mm

    Standard deviation of the cut length from the cutting mechanism alone (standstill registration)

    Szenario · Gleichverteilt 0,2 bis 0,4 mm

    Deklarierte Annahme
  • σt\sigma_t0,2 ms

    Timing jitter of print-mark detection and cut actuation

    Szenario · Gleichverteilt 0,05 bis 0,4 ms

    Deklarierte Annahme

    A timing error becomes a length error v_web sigma_t; declared assumption.

  • zz3,5

    Capability margin of the overlap in standard deviations

    Szenario · Gleichverteilt 3 bis 4

    Deklarierte Annahme

    Operating choice, point value at the centre of the declared range.

  • vmaxv_{max}3 m/s

    Maximum label-web speed of the declared labeller

    Szenario · Gleichverteilt 2 bis 4 m/s

    Deklarierte Annahme

    Machine design value; no open source was used.

  • Δv\Delta_v1,5 mm

    Allowed vertical displacement of the label on the panel

    Szenario · Gleichverteilt 1 bis 2 mm

    Deklarierte Annahme
  • σv\sigma_v0,3 mm

    Standard deviation of the vertical label position

    Szenario · Gleichverteilt 0,2 bis 0,5 mm

    Deklarierte Annahme
  • TgT_g120 °C

    Application temperature of the hot-melt glue

    Szenario · Gleichverteilt 110 bis 140 °C

    Deklarierte Annahme
  • T0T_025 °C

    Ambient temperature

    Szenario · Fest

    Deklarierte Annahme
  • mgm_g30 mg

    Mass of hot-melt glue per label (pick-up and overlap beads)

    Szenario · Gleichverteilt 15 bis 60 mg

    Deklarierte Annahme
  • cp,gc_{p,g}2 kJ/kg/K

    Specific heat of the hot-melt glue

    Szenario · Gleichverteilt 1,8 bis 2,6 kJ/kg/K

    Deklarierte Annahme

    Typical of polymer melts; no open source was used. Declared assumption.

  • mpm_p0,52 kg

    Mass of product per container

    Szenario · Fest

    Deklarierte Annahme

    0.5 L of a sweetened soft drink of density about 1040 kg/m3.

  • LrL_r4.000 m

    Label-web length on one reel

    Szenario · Gleichverteilt 2.000 bis 6.000 m

    Deklarierte Annahme
  • LwL_w2 m

    Label web wasted at each reel splice

    Szenario · Gleichverteilt 1 bis 5 m

    Deklarierte Annahme
  • nsun_{su}30

    Labels wasted while registration settles after a changeover

    Szenario · Gleichverteilt 10 bis 60

    Deklarierte Annahme
  • tcampt_{camp}8 h

    Production time between two label changeovers

    Szenario · Gleichverteilt 4 bis 24 h

    Deklarierte Annahme
  • tspt_{sp}3 min

    Machine stop per manual reel change and splice (zero with an automatic splicer)

    Szenario · Gleichverteilt 1 bis 6 min

    Deklarierte Annahme
  • n˙doc\dot n_{doc}33.197 1/h

    Set performance of the labelling machine of an industrial bottling plant (glass bottles, wet-glue labels; measured)

    Vergleichswert · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    Labelling machine 33,197 30 1423 40 97.3Simulation of Energy and Media Demand of Beverage Bottling Plants by Automatic Model Generation (Bär, R. M.; Zeilmann, M.; Nophut, C.; Kleinert, J.; Beyer, K.; Voigt, T.), Sustainability 13, 10089 (2021), CC BY 4.0 (öffnet in neuem Tab). MDPI (copy distributed by a co-author's institution), 2021. S. 18. doi:10.3390/su131810089
  • MTBFMTBF1.423 s

    Measured mean time between failures of the labelling machine

    Vergleichswert · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    Labelling machine 33,197 30 1423 40 97.3Simulation of Energy and Media Demand of Beverage Bottling Plants by Automatic Model Generation (Bär, R. M.; Zeilmann, M.; Nophut, C.; Kleinert, J.; Beyer, K.; Voigt, T.), Sustainability 13, 10089 (2021), CC BY 4.0 (öffnet in neuem Tab). MDPI (copy distributed by a co-author's institution), 2021. S. 18. doi:10.3390/su131810089
  • MTTRMTTR40 s

    Measured mean time to repair of the labelling machine

    Vergleichswert · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    Labelling machine 33,197 30 1423 40 97.3Simulation of Energy and Media Demand of Beverage Bottling Plants by Automatic Model Generation (Bär, R. M.; Zeilmann, M.; Nophut, C.; Kleinert, J.; Beyer, K.; Voigt, T.), Sustainability 13, 10089 (2021), CC BY 4.0 (öffnet in neuem Tab). MDPI (copy distributed by a co-author's institution), 2021. S. 18. doi:10.3390/su131810089

8Vergleichswerte

Dokumentierte Werte aus offenen Quellen zur Prüfung der Obergrenzen; kein dokumentierter Wert darf die theoretische Grenze übertreffen.
VergleichswertObergrenzeWertHerkunft
Availability of the labelling machine of an industrial bottling plant, measured (MTBF / (MTBF + MTTR))
Wörtliches Zitat anzeigen
Labelling machine 33,197 30 1423 40 97.3Simulation of Energy and Media Demand of Beverage Bottling Plants by Automatic Model Generation (Bär, R. M.; Zeilmann, M.; Nophut, C.; Kleinert, J.; Beyer, K.; Voigt, T.), Sustainability 13, 10089 (2021), CC BY 4.0 (öffnet in neuem Tab). MDPI (copy distributed by a co-author's institution), 2021. S. 18. doi:10.3390/su131810089
Best dokumentiert97,3 %Verifiziertes Zitat

9Unvermeidbare Stillstände

Stillstände, die Physik oder Regulierung erzwingen; sie bestimmen die maximale Verfügbarkeit.

10Annahmen

  1. Label cut length, container diameter and vertical position are independent normal variables; the registration error of the cut grows with the web speed as v_web times the timing jitter of mark detection and cut.
  2. A label is nonconforming when its overlap is shorter than the minimum glue seam or when it lies outside the vertical tolerance; wrinkles, flags, glue defects and print defects are not modelled, so the quality ceiling is an upper bound. A nonconforming container is rejected (quality loss); the container and its product are not counted as yield loss.
  3. Performance: the ideal cycle is that of the maximum web speed of the declared machine; the capable process runs at the largest web speed at which the overlap keeps the declared capability margin. Machine design values (web speed, glue mass) are declared, so the rates are reported without a theoretical label.
  4. Availability: no stop is forced by physics or regulation, so availability_max = 1; manual reel splices enter only availability_scenario and oee_scenario, and the documented random failures of a labelling machine only availability_documented. No cleaning-in-place applies to a labeller, so the cleaning model is not used.
  5. The documented machine is a wet-glue labeller of returnable glass bottles in a mineral-water and soft-drink plant; its set performance and failure behaviour are used as the documented level of a labelling machine in a bottling line, not as a property of the roll-fed scenario.

11Gültigkeitsbereich

  • Wrap-around labels on cylindrical label panels (bottles or cans) with a glued overlap seam; pressure-sensitive, sleeve and wet-glue patch labels have other failure modes.

12Sensitivität

Elastizität: relative Änderung der Ergebnisgröße bei relativer Änderung jedes Parameters. Daneben steht die Spearman-Rangkorrelation aus den Monte-Carlo-Ziehungen.
  • Δv\Delta_vAllowed vertical displacement of the label on the panel
    Elastizität 0,000Spearman-ρ +0,44
  • σv\sigma_vStandard deviation of the vertical label position
    Elastizität 0,000Spearman-ρ -0,58
  • ono_nNominal overlap of the trailing edge over the leading edge (label design)
    Elastizität 0,000Spearman-ρ +0,17
  • omino_{min}Least overlap that still carries the full glue bead of the seam
    Elastizität 0,000Spearman-ρ -0,08
  • σt\sigma_tTiming jitter of print-mark detection and cut actuation
    Elastizität 0,000Spearman-ρ -0,32
  • vmaxv_{max}Maximum label-web speed of the declared labeller
    Elastizität 0,000Spearman-ρ -0,20
  • σD\sigma_DStandard deviation of the label-panel diameter from container to container
    Elastizität 0,000Spearman-ρ -0,05
  • σL,0\sigma_{L,0}Standard deviation of the cut length from the cutting mechanism alone (standstill registration)
    Elastizität 0,000Spearman-ρ -0,03
  • zzCapability margin of the overlap in standard deviations
    Elastizität 0,000Spearman-ρ -0,04
  • Größe steigt mit dem Parameter
  • Größe sinkt mit dem Parameter

13Validierungsprüfungen

Ein Modell wird nur veröffentlicht, wenn alle Prüfungen bestanden sind.
  • Dimensionsanalyse22 outputs converted to their declared unitsBestanden
  • Jeder zitierte Wert an seiner Quelle verifiziert5 verified, 0 failedBestanden
  • Kein dokumentierter Wert übertrifft die theoretische GrenzeBestanden
  • Obergrenzen in physikalischer ReihenfolgeBestanden
  • Anteile zwischen 0 und 1Bestanden

14Verlustursachen in dieser Operation

Wahrscheinlichkeit, dass jede Ursache als relevanter Verlust einer Linie dokumentiert ist, gepoolt über alle Segmente.

15Literatur

  1. Simulation of Energy and Media Demand of Beverage Bottling Plants by Automatic Model Generation (Bär, R. M.; Zeilmann, M.; Nophut, C.; Kleinert, J.; Beyer, K.; Voigt, T.), Sustainability 13, 10089 (2021), CC BY 4.0 (öffnet in neuem Tab). MDPI (copy distributed by a co-author's institution), 2021. S. 18. doi:10.3390/su131810089
  2. doi:10.3390/su131810089 — Bottling-plant simulation with measured set performances, MTBF and MTTR of every machine (Table A1).