foratvise
Loslegen
Leerlauf und Kurzstillstände

Component fouling from residue and degraded lubricant

Leerlauf und KurzstillständeLeistungGesamte Linie oder nicht spezifizierte Anlage

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei etwa 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 53 % der Verlustzeit der Linie. Berichtet von 1 der 127 Studien, die sie beobachten konnten (spärliche Evidenz).

Was passiert

Over time, product residue, dust or debris accumulates on moving parts, or lubricant oxidizes and loses viscosity (burning) under heat and friction, so that the lubricating film breaks down. This allows direct metal-to-metal contact or sticky deposits to restrict the free movement of rollers, guides, chains or shafts, causing the component to seize or jam intermittently.

Was man dagegen tut

Implement a scheduled lubrication and cleaning program sized to actual soiling and thermal load, using the correct lubricant grade for the operating temperature, and inspect/replace lubricant before it degrades. Add routine wipe-down or residue removal on exposed moving parts and monitor component temperature or current as an early warning of friction build-up.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
0,5 % [0,1–1,4 %]
Erwarteter Anteil an der Verlustzeit
0,3 % [0,1–0,7 %]
Anteil an der Verlustzeit bei Auftreten
53 % [41–65 %]
Studien / Einheiten
127 / 161
Evidenzgrad
D

Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    0,6 % [0,1–2,2 %]13 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    0,5 % [0,1–1,8 %]26 Studien
  • Bier, Wein und Spirituosen
    0,6 % [0,1–2,1 %]11 Studien
  • Backwaren und Teigwaren
    0,5 % [0,1–1,9 %]24 Studien
  • Fleisch, Geflügel und Fisch
    0,6 % [0,1–2,2 %]9 Studien
  • Obst- und Gemüseverarbeitung
    0,6 % [0,1–2,1 %]7 Studien
  • Getreide- und Ölsaatenmüllerei
    0,9 % [0,1–3,5 %]6 Studien
  • Zucker und Süßwaren
    0,6 % [0,1–2,2 %]9 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    0,6 % [0,1–2,2 %]5 Studien
  • Futtermittel und Heimtiernahrung
    0,6 % [0,1–2,4 %]7 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    0,6 % [0,1–2,2 %]10 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

Over time, product residue, dust or debris accumulates on moving parts, or lubricant oxidizes and loses viscosity (burning) under heat and friction, so that the lubricating film breaks down. This allows direct metal-to-metal contact or sticky deposits to restrict the free movement of rollers, guides, chains or shafts, causing the component to seize or jam intermittently.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

Short, recurring stop events on the same component or axis, often with rising motor current or torque trend prior to the stop, and no fault code requiring maintenance intervention beyond operator clearing. Historical trend shows increasing frequency of micro-stops as lubricant condition or fouling worsens between cleaning/lubrication cycles.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Implement a scheduled lubrication and cleaning program sized to actual soiling and thermal load, using the correct lubricant grade for the operating temperature, and inspect/replace lubricant before it degrades. Add routine wipe-down or residue removal on exposed moving parts and monitor component temperature or current as an early warning of friction build-up.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Anteil an der geplanten Zeit: 3,45 % · laut Bericht: “friction between components caused by burnt lubricant”
    Wörtliches Zitat anzeigen
    High downtime rate due to friction between components caused by burnt lubricant 3.45% 2.17% 2.90%
  2. Anteil an der geplanten Zeit: 10,4 % · laut Bericht: “component blockage caused by residue buildup”
    Wörtliches Zitat anzeigen
    High downtime rate due to component blockage caused by residue buildup 10.39% 6.52% 3.48%