Mold Safety Cam/Closure Mechanism Fault
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 57 % der Verlustzeit der Linie. Berichtet von 1 der 76 Studien, die sie beobachten konnten (spärliche Evidenz).
Was passiert
In blow molding machines, the mold halves are closed and held shut by a cam-driven safety interlock that must fully engage before the blowing cycle can proceed. Wear, misalignment or contamination of the cam, linkage or locking pins prevents proper closure or triggers the safety interlock, stopping the machine or forcing manual readjustment, and the same mechanism often needs recalibration whenever mold tooling is changed over.
Was man dagegen tut
Implement preventive maintenance covering inspection, cleaning and lubrication of the cam profile, linkage and interlock sensors, with scheduled replacement based on wear condition. Standardize the mold closure verification and calibration step within the changeover procedure so the safety mechanism is checked and adjusted whenever tooling or format is changed.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,7 % [0,1–2,1 %]
- Erwarteter Anteil an der Verlustzeit
- 0,4 % [0,1–1,2 %]
- Anteil an der Verlustzeit bei Auftreten
- 57 % [46–68 %]
- Studien / Einheiten
- 76 / 96
- Evidenzgrad
- D
Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,9 % [0,1–3,2 %]5 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte1,1 % [0,1–4,1 %]11 Studien
- Bier, Wein und Spirituosen0,9 % [0,1–3,3 %]0 Studien
- Backwaren und Teigwaren0,7 % [0,1–2,5 %]25 Studien
- Fleisch, Geflügel und Fisch0,9 % [0,1–3,2 %]3 Studien
- Obst- und Gemüseverarbeitung0,9 % [0,1–3,2 %]3 Studien
- Getreide- und Ölsaatenmüllerei0,9 % [0,1–3,4 %]0 Studien
- Zucker und Süßwaren0,8 % [0,1–2,9 %]8 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel0,8 % [0,1–3,1 %]7 Studien
- Futtermittel und Heimtiernahrung0,8 % [0,1–3,3 %]6 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)0,8 % [0,1–3,2 %]8 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseIn blow molding machines, the mold halves are closed and held shut by a cam-driven safety interlock that must fully engage before the blowing cycle can proceed. Wear, misalignment or contamination of the cam, linkage or locking pins prevents proper closure or triggers the safety interlock, stopping the machine or forcing manual readjustment, and the same mechanism often needs recalibration whenever mold tooling is changed over.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseSCADA/MES logs show discrete fault or alarm tags referencing mold closure, safety cam or interlock position, recurring short-to-medium machine-state stops at the mold-close step of the cycle, and a cluster of downtime events immediately following changeover or tooling-change timestamps. Cycle-time traces often show the mold-close phase taking longer or timing out before the fault is raised.
Gegenmaßnahme
Ingenieurpraktische HinweiseImplement preventive maintenance covering inspection, cleaning and lubrication of the cam profile, linkage and interlock sensors, with scheduled replacement based on wear condition. Standardize the mold closure verification and calibration step within the changeover procedure so the safety mechanism is checked and adjusted whenever tooling or format is changed.
4Quellen
- Analisis Total Productive Maintenance (TPM) dengan Menggunakan Metode Overall Equipment Effectiveness (OEE) pada Mesin Blowing (2025)Quelle öffnenVerlustzeit: 135 menit · laut Bericht: “Mold Safety Cam Closure”
Wörtliches Zitat anzeigen
Mold Safety Cam Closure 135
- Analisis Total Productive Maintenance (TPM) dengan Menggunakan Metode Overall Equipment Effectiveness (OEE) pada Mesin Blowing (2025)Quelle öffnenAnteil an der Verlustzeit: 6,10 % · laut Bericht: “Equipment Failure Losses”
Wörtliches Zitat anzeigen
Rata - rata 6,10 0,95 11,47 0,00 0,00 0,21
- Analisis Total Productive Maintenance (TPM) dengan Menggunakan Metode Overall Equipment Effectiveness (OEE) pada Mesin Blowing (2025)Quelle öffnenAnteil an der Verlustzeit: 0,950 % · laut Bericht: “Set Up & Adjustment Losses”
Wörtliches Zitat anzeigen
Rata - rata 6,10 0,95 11,47 0,00 0,00 0,21

