Packaging/filling seal and handling mechanism fault
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 52 % der Verlustzeit der Linie. Berichtet von 2 der 112 Studien, die sie beobachten konnten (begrenzte Evidenz).
Was passiert
Components that hold, position or seal the container during filling and packaging (sealing jaws, heat-sealing/induction elements, slings or belts that carry the pack through the machine) wear, lose tension or fall out of alignment. This produces incomplete or weak seals that leak, and at the same time causes the container or film to misfeed, jam or trigger a sensor fault that halts the machine.
Was man dagegen tut
Implement a preventive maintenance and inspection routine for sealing jaws, heating/induction elements and sling or belt tension, with periodic verification of seal integrity and mechanical alignment. Add sensors or seal-quality checks that flag degradation before it causes leaks or stoppages, and train operators to quickly clear jams while logging root cause.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,8 % [0,2–2,0 %]
- Erwarteter Anteil an der Verlustzeit
- 0,4 % [0,1–1,1 %]
- Anteil an der Verlustzeit bei Auftreten
- 52 % [40–64 %]
- Studien / Einheiten
- 112 / 155
- Evidenzgrad
- C
Grad C: 2 bis 4 Studien oder eine Intervallbreite über 0,35.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,8 % [0,1–3,0 %]14 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte0,7 % [0,1–2,2 %]33 Studien
- Bier, Wein und Spirituosen0,8 % [0,1–2,9 %]14 Studien
- Backwaren und Teigwaren0,9 % [0,1–3,4 %]6 Studien
- Fleisch, Geflügel und Fisch0,9 % [0,1–3,0 %]6 Studien
- Obst- und Gemüseverarbeitung0,9 % [0,1–3,1 %]4 Studien
- Getreide- und Ölsaatenmüllerei0,9 % [0,1–3,1 %]4 Studien
- Zucker und Süßwaren0,9 % [0,1–3,3 %]4 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel1,3 % [0,2–4,5 %]8 Studien
- Futtermittel und Heimtiernahrung0,9 % [0,1–3,6 %]5 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)1,2 % [0,1–4,2 %]14 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseComponents that hold, position or seal the container during filling and packaging (sealing jaws, heat-sealing/induction elements, slings or belts that carry the pack through the machine) wear, lose tension or fall out of alignment. This produces incomplete or weak seals that leak, and at the same time causes the container or film to misfeed, jam or trigger a sensor fault that halts the machine.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseShort, repeated machine-state transitions to stopped or fault without an associated maintenance work order, often logged as minor stops or jams on the sealing/packaging station; concurrently, quality or vision-inspection counters show rising rejects for leaking or poorly sealed packs. Upstream filling or capping stations may show blocking as the affected station accumulates stop time.
Gegenmaßnahme
Ingenieurpraktische HinweiseImplement a preventive maintenance and inspection routine for sealing jaws, heating/induction elements and sling or belt tension, with periodic verification of seal integrity and mechanical alignment. Add sensors or seal-quality checks that flag degradation before it causes leaks or stoppages, and train operators to quickly clear jams while logging root cause.
4Quellen
- Efficiency Improvement of Glass Bottle Filler Machine Using Autonomous Maintenance-A Case Study (2025)Quelle öffnenVerlustzeit: 10,0 min · laut Bericht: “HIP problem”
Wörtliches Zitat anzeigen
HIP problem 0 0 10 0 0 0 10 0.68
- Efficiency Improvement of Glass Bottle Filler Machine Using Autonomous Maintenance-A Case Study (2025)Quelle öffnenAnteil an der Verlustzeit: 0,680 % · laut Bericht: “HIP problem”
Wörtliches Zitat anzeigen
HIP problem 0 0 10 0 0 0 10 0.68
- Fehlerquote: 0,270 % · laut Bericht: “leakage problems”
Wörtliches Zitat anzeigen
leakage problems reduced from 1.20% to 0.27%
- Fehlerquote: 1,20 % · laut Bericht: “leakage problems”
Wörtliches Zitat anzeigen
leakage problems reduced from 1.20% to 0.27%
- PENURUNAN DOWNTIME UNTUK MENINGKATKAN ACHIEVEMENT (ACH) MELALUI IMPLEMENTASI TPM (TOTAL PRODUCTIVE MAINTENANCE) DAN ANALISIS SIX BIG LOSSES DI PT TES HF (2026)Quelle öffnenAnzahl der Ereignisse: 700 events · laut Bericht: “slendang problem”
Wörtliches Zitat anzeigen
slendang problem sebanyak 700 kejadian (15,11%)
- PENURUNAN DOWNTIME UNTUK MENINGKATKAN ACHIEVEMENT (ACH) MELALUI IMPLEMENTASI TPM (TOTAL PRODUCTIVE MAINTENANCE) DAN ANALISIS SIX BIG LOSSES DI PT TES HF (2026)Quelle öffnenAnteil an den Verlustereignissen: 15,1 % · laut Bericht: “slendang problem”
Wörtliches Zitat anzeigen
slendang problem sebanyak 700 kejadian (15,11%)

