Palletizer minor stoppage (misalignment, jam or blockage)
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 54 % der Verlustzeit der Linie. Berichtet von 2 der 112 Studien, die sie beobachten konnten (begrenzte Evidenz).
Was passiert
Short stops arise at the palletizer when incoming bottles, bundles, layers or pallets are not correctly positioned by the guides, when a bundle falls or jams on the infeed or layer-forming station, or when the machine is starved by lack of containers upstream or blocked because the output pallet transport or warehouse buffer is full. Position and presence sensors detect the fault and the control system halts the cycle automatically until the condition is cleared.
Was man dagegen tut
Keep infeed guides, photocells and position sensors calibrated and well maintained, adjust container/bundle/layer guiding and centering devices, and size buffer conveyors and pallet transport capacity to absorb normal rate variability between the palletizer and the warehouse. Standardize quick-clear procedures and visual diagnostics so operators can resolve alignment, jam or blockage faults rapidly without escalating to maintenance.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,7 % [0,2–1,8 %]
- Erwarteter Anteil an der Verlustzeit
- 0,4 % [0,1–1,0 %]
- Anteil an der Verlustzeit bei Auftreten
- 54 % [41–66 %]
- Studien / Einheiten
- 112 / 155
- Evidenzgrad
- C
Grad C: 2 bis 4 Studien oder eine Intervallbreite über 0,35.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,8 % [0,1–2,7 %]14 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte1,2 % [0,2–3,5 %]33 Studien
- Bier, Wein und Spirituosen0,7 % [0,1–2,6 %]14 Studien
- Backwaren und Teigwaren0,8 % [0,1–2,8 %]6 Studien
- Fleisch, Geflügel und Fisch0,8 % [0,1–2,8 %]6 Studien
- Obst- und Gemüseverarbeitung0,8 % [0,1–3,0 %]4 Studien
- Getreide- und Ölsaatenmüllerei0,8 % [0,1–2,9 %]4 Studien
- Zucker und Süßwaren0,8 % [0,1–3,0 %]4 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel0,8 % [0,1–2,7 %]8 Studien
- Futtermittel und Heimtiernahrung0,8 % [0,1–3,0 %]5 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)0,7 % [0,1–2,6 %]14 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseShort stops arise at the palletizer when incoming bottles, bundles, layers or pallets are not correctly positioned by the guides, when a bundle falls or jams on the infeed or layer-forming station, or when the machine is starved by lack of containers upstream or blocked because the output pallet transport or warehouse buffer is full. Position and presence sensors detect the fault and the control system halts the cycle automatically until the condition is cleared.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseSCADA/MES logs show a high count of brief minor-stop events on the palletizer with alarm tags referring to misalignment, incorrect stratum/layer, fallen bundle, warehouse full or lack of bottles in entrance; individual durations are short but frequent, and the pattern often coincides with starved or blocked states shared with the upstream filling/capping line or the downstream transport and warehouse system.
Gegenmaßnahme
Ingenieurpraktische HinweiseKeep infeed guides, photocells and position sensors calibrated and well maintained, adjust container/bundle/layer guiding and centering devices, and size buffer conveyors and pallet transport capacity to absorb normal rate variability between the palletizer and the warehouse. Standardize quick-clear procedures and visual diagnostics so operators can resolve alignment, jam or blockage faults rapidly without escalating to maintenance.
4Quellen
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenAnteil an den Verlustereignissen: 4,57 % · laut Bericht: “Pallet not Alligned (Palletizer Entry)”
Wörtliches Zitat anzeigen
E Pallet not Alligned (Palletizer Entry) 4,57% 77,92%
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenAnteil an den Verlustereignissen: 10,4 % · laut Bericht: “Pallets Warehouse Allarm”
Wörtliches Zitat anzeigen
C Pallets Warehouse Allarm 10,38% 64,36%
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenAnteil an den Verlustereignissen: 12,6 % · laut Bericht: “Uncorrect Stratum (N°2)”
Wörtliches Zitat anzeigen
B Uncorrect Stratum (N°2) 12,60% 53,98%
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenAnteil an den Verlustereignissen: 9,00 % · laut Bericht: “Uncorrect Stratum (N°1)”
Wörtliches Zitat anzeigen
D Uncorrect Stratum (N°1) 9,00% 73,36%
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenAnteil an den Verlustereignissen: 41,4 % · laut Bericht: “Bundle not Alligned (Palletizer)”
Wörtliches Zitat anzeigen
A Bundle not Alligned (Palletizer) 41,38% 41,38%
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenAnteil an den Verlustereignissen: 3,60 % · laut Bericht: “Fallen Bundle (Palletizer)”
Wörtliches Zitat anzeigen
F Fallen Bundle (Palletizer) 3,60% 81,52%
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenZeit zwischen Ereignissen: 603 s · laut Bericht: “Bundle not Alligned (Palletizer)”
Wörtliches Zitat anzeigen
MTTF(s) 602,658 293143,4 780 2070 3798,75 1016,58 MTTR(s) 17,8571 34,2857 57,5 48,75 67,5 24,335
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenZeit zwischen Ereignissen: 293.143 s · laut Bericht: “Uncorrect Stratum (N°2)”
Wörtliches Zitat anzeigen
MTTF(s) 602,658 293143,4 780 2070 3798,75 1016,58 MTTR(s) 17,8571 34,2857 57,5 48,75 67,5 24,335
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenZeit zwischen Ereignissen: 780 s · laut Bericht: “Pallets Warehouse Allarm”
Wörtliches Zitat anzeigen
MTTF(s) 602,658 293143,4 780 2070 3798,75 1016,58 MTTR(s) 17,8571 34,2857 57,5 48,75 67,5 24,335
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenZeit zwischen Ereignissen: 2.070 s · laut Bericht: “Uncorrect Stratum (N°1)”
Wörtliches Zitat anzeigen
MTTF(s) 602,658 293143,4 780 2070 3798,75 1016,58 MTTR(s) 17,8571 34,2857 57,5 48,75 67,5 24,335
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenZeit zwischen Ereignissen: 3.799 s · laut Bericht: “Pallet not Alligned (Palletizer Entry)”
Wörtliches Zitat anzeigen
MTTF(s) 602,658 293143,4 780 2070 3798,75 1016,58 MTTR(s) 17,8571 34,2857 57,5 48,75 67,5 24,335
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenMittlere Ereignisdauer: 17,9 s · laut Bericht: “Bundle not Alligned (Palletizer)”
Wörtliches Zitat anzeigen
MTTF(s) 602,658 293143,4 780 2070 3798,75 1016,58 MTTR(s) 17,8571 34,2857 57,5 48,75 67,5 24,335
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenMittlere Ereignisdauer: 34,3 s · laut Bericht: “Uncorrect Stratum (N°2)”
Wörtliches Zitat anzeigen
MTTF(s) 602,658 293143,4 780 2070 3798,75 1016,58 MTTR(s) 17,8571 34,2857 57,5 48,75 67,5 24,335
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenMittlere Ereignisdauer: 57,5 s · laut Bericht: “Pallets Warehouse Allarm”
Wörtliches Zitat anzeigen
MTTF(s) 602,658 293143,4 780 2070 3798,75 1016,58 MTTR(s) 17,8571 34,2857 57,5 48,75 67,5 24,335
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenMittlere Ereignisdauer: 48,8 s · laut Bericht: “Uncorrect Stratum (N°1)”
Wörtliches Zitat anzeigen
MTTF(s) 602,658 293143,4 780 2070 3798,75 1016,58 MTTR(s) 17,8571 34,2857 57,5 48,75 67,5 24,335
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenMittlere Ereignisdauer: 67,5 s · laut Bericht: “Pallet not Alligned (Palletizer Entry)”
Wörtliches Zitat anzeigen
MTTF(s) 602,658 293143,4 780 2070 3798,75 1016,58 MTTR(s) 17,8571 34,2857 57,5 48,75 67,5 24,335
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenAnzahl der Ereignisse: 168 events · laut Bericht: “Bundle not Alligned (Palletizer)”
Wörtliches Zitat anzeigen
A 168 566.8 761.2 1.343 0 6240
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenAnzahl der Ereignisse: 7,00 events · laut Bericht: “Uncorrect Stratum (N°2)”
Wörtliches Zitat anzeigen
B 7 2931 2925 0.9978 180 8160
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenAnzahl der Ereignisse: 4,00 events · laut Bericht: “Pallets Warehouse Allarm”
Wörtliches Zitat anzeigen
C 4 780 467 0.5991 240 1200
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenAnzahl der Ereignisse: 8,00 events · laut Bericht: “Uncorrect Stratum (N°1)”
Wörtliches Zitat anzeigen
D 8 2070 1546 0.7471 540 4680
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenAnzahl der Ereignisse: 16,0 events · laut Bericht: “Pallet not Alligned (Palletizer Entry)”
Wörtliches Zitat anzeigen
E 16 3799 3082 0.8114 360 9420
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenVerlustzeit: 694 min · laut Bericht: “Lack bottles in entrance”
Wörtliches Zitat anzeigen
Lack bottles in entrance 694,38 32,46% 32,46%
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenAnteil an der Verlustzeit: 32,5 % · laut Bericht: “Lack bottles in entrance”
Wörtliches Zitat anzeigen
Lack bottles in entrance 694,38 32,46% 32,46%
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenVerlustzeit: 615 min · laut Bericht: “Output Transports full”
Wörtliches Zitat anzeigen
Output Transports full 615,10 28,75% 61,21%
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenAnteil an der Verlustzeit: 28,8 % · laut Bericht: “Output Transports full”
Wörtliches Zitat anzeigen
Output Transports full 615,10 28,75% 61,21%
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenVerlustzeit: 219 min · laut Bericht: “Bottles not aligned in entrance”
Wörtliches Zitat anzeigen
Bottles not aligned in entrance 218,67 10,22% 71,43%
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenAnteil an der Verlustzeit: 10,2 % · laut Bericht: “Bottles not aligned in entrance”
Wörtliches Zitat anzeigen
Bottles not aligned in entrance 218,67 10,22% 71,43%
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenVerlustzeit: 131 min · laut Bericht: “Pallet not alligned”
Wörtliches Zitat anzeigen
Pallet not alligned 130,58 6,10% 77,53%
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenAnteil an der Verlustzeit: 6,10 % · laut Bericht: “Pallet not alligned”
Wörtliches Zitat anzeigen
Pallet not alligned 130,58 6,10% 77,53%
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenVerlustzeit: 108 min · laut Bericht: “Products layer uncorrect”
Wörtliches Zitat anzeigen
Products layer uncorrect 108,00 5,05% 82,58%
- Total productive maintenance models and tools in flow line manufacturing systems (2017)Quelle öffnenAnteil an der Verlustzeit: 5,05 % · laut Bericht: “Products layer uncorrect”
Wörtliches Zitat anzeigen
Products layer uncorrect 108,00 5,05% 82,58%
- Analisa Efektifitas Mesin Palletizer Menggunakan Metode OEE Dan Identifikasi Kegagalan Dengan FMEA (2025)Quelle öffnenVerlustzeit: 188 min · laut Bericht: “Palletizer”
Wörtliches Zitat anzeigen
4 Palletizer 188 55%
- Analisa Efektifitas Mesin Palletizer Menggunakan Metode OEE Dan Identifikasi Kegagalan Dengan FMEA (2025)Quelle öffnenAnteil an der Verlustzeit: 55,0 % · laut Bericht: “Palletizer”
Wörtliches Zitat anzeigen
4 Palletizer 188 55%
- Verlustzeit: 157 min · laut Bericht: “Palletizer”
Wörtliches Zitat anzeigen
Operational losses (min) | 278 | 494 | 106 | 53 | 157 | 1088 | 48
- Verlustzeit: 152 min · laut Bericht: “Palletizer”
Wörtliches Zitat anzeigen
Equipment losses (min) | 420 | 364 | 24 | 55 | 152 | 1015 | 44.8

