foratvise
Loslegen
Anlagenausfall (Störungen)

Product pusher bushing wear/failure

Anlagenausfall (Störungen)VerfügbarkeitFormen, Gießen und Dosieren

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei etwa 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 58 % der Verlustzeit der Linie. Berichtet von 1 der 76 Studien, die sie beobachten konnten (spärliche Evidenz).

Was passiert

The bushing that guides and supports the reciprocating product pusher arm on the forming machine wears down through repeated friction and mechanical cycling, or fails due to lack of lubrication or misalignment. As clearance increases, the pusher loses precise motion, binds, or jams, interrupting the forming cycle and requiring mechanical intervention to repair or replace the component.

Was man dagegen tut

Implement a preventive maintenance schedule with periodic inspection, lubrication and timely replacement of the pusher bushing based on wear condition, and verify shaft alignment during installation to minimize abnormal loading.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
0,7 % [0,1–2,0 %]
Erwarteter Anteil an der Verlustzeit
0,4 % [0,1–1,2 %]
Anteil an der Verlustzeit bei Auftreten
58 % [47–68 %]
Studien / Einheiten
76 / 96
Evidenzgrad
D

Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    0,9 % [0,1–3,2 %]5 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    0,8 % [0,1–2,9 %]11 Studien
  • Bier, Wein und Spirituosen
    0,9 % [0,1–3,4 %]0 Studien
  • Backwaren und Teigwaren
    0,7 % [0,1–2,6 %]25 Studien
  • Fleisch, Geflügel und Fisch
    0,9 % [0,1–3,4 %]3 Studien
  • Obst- und Gemüseverarbeitung
    0,9 % [0,1–3,4 %]3 Studien
  • Getreide- und Ölsaatenmüllerei
    0,9 % [0,1–3,6 %]0 Studien
  • Zucker und Süßwaren
    0,8 % [0,1–3,0 %]8 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    1,2 % [0,1–4,6 %]7 Studien
  • Futtermittel und Heimtiernahrung
    0,9 % [0,1–3,3 %]6 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    0,9 % [0,1–3,2 %]8 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

The bushing that guides and supports the reciprocating product pusher arm on the forming machine wears down through repeated friction and mechanical cycling, or fails due to lack of lubrication or misalignment. As clearance increases, the pusher loses precise motion, binds, or jams, interrupting the forming cycle and requiring mechanical intervention to repair or replace the component.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

SCADA/MES data shows an unplanned stop state on the forming machine with a mechanical fault or jam alarm associated with the pusher axis, often preceded by increasing cycle time variability or torque/current fluctuations on the pusher drive before the full stop. Downstream stations may show starvation once the fault halts product flow.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Implement a preventive maintenance schedule with periodic inspection, lubrication and timely replacement of the pusher bushing based on wear condition, and verify shaft alignment during installation to minimize abnormal loading.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Verlustzeit: 601 menit · laut Bericht: “pendorong produk (bushing)”
    Wörtliches Zitat anzeigen
    equipment failure yang mendominasi pada mesin Sapal adalah pendorong produk (bushing) yaitu sebanyak 601 menit atau 10,01 jam.