Station cycle time constraint
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 66 % der Verlustzeit der Linie. Berichtet von 1 der 127 Studien, die sie beobachten konnten (spärliche Evidenz).
Was passiert
A line station (e.g. a lotting/grouping head, spraying unit or unpacking device) has an inherent mechanical or process dwell time that limits how fast it can complete each cycle, so it paces the whole line below the ideal design rate. Because the constraint is built into the mechanism itself rather than a fault, the station runs continuously but slower than the target takt, and this pace propagates to neighbouring equipment.
Was man dagegen tut
Perform a time-and-motion study to confirm the station as the line bottleneck, then rebalance capacity by adding a parallel or duplicate head, shortening the mechanical dwell through redesign, or introducing buffer accumulation to decouple its pace from neighbouring stations. Where the constraint cannot be removed, reset the line's target rate to the realistic capacity of the limiting station to avoid chasing an unattainable speed.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,7 % [0,1–1,8 %]
- Erwarteter Anteil an der Verlustzeit
- 0,4 % [0,1–1,2 %]
- Anteil an der Verlustzeit bei Auftreten
- 66 % [53–77 %]
- Studien / Einheiten
- 127 / 161
- Evidenzgrad
- D
Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,7 % [0,1–2,6 %]13 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte0,7 % [0,1–2,2 %]26 Studien
- Bier, Wein und Spirituosen0,8 % [0,1–2,7 %]11 Studien
- Backwaren und Teigwaren0,7 % [0,1–2,3 %]24 Studien
- Fleisch, Geflügel und Fisch1,1 % [0,1–3,8 %]9 Studien
- Obst- und Gemüseverarbeitung0,8 % [0,1–2,8 %]7 Studien
- Getreide- und Ölsaatenmüllerei0,8 % [0,1–2,8 %]6 Studien
- Zucker und Süßwaren0,8 % [0,1–2,6 %]9 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel0,8 % [0,1–2,7 %]5 Studien
- Futtermittel und Heimtiernahrung0,8 % [0,1–2,8 %]7 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)0,8 % [0,1–2,8 %]10 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseA line station (e.g. a lotting/grouping head, spraying unit or unpacking device) has an inherent mechanical or process dwell time that limits how fast it can complete each cycle, so it paces the whole line below the ideal design rate. Because the constraint is built into the mechanism itself rather than a fault, the station runs continuously but slower than the target takt, and this pace propagates to neighbouring equipment.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseSCADA/MES shows the station's actual cycle time flat at a value close to its mechanical limit, well above the target cycle time, with no associated fault or stop alarms. The line speed or output counter trends persistently below the ideal rate while the station state stays in run, and adjacent upstream equipment may show intermittent blocking or downstream starvation synchronized with this pacing station.
Gegenmaßnahme
Ingenieurpraktische HinweisePerform a time-and-motion study to confirm the station as the line bottleneck, then rebalance capacity by adding a parallel or duplicate head, shortening the mechanical dwell through redesign, or introducing buffer accumulation to decouple its pace from neighbouring stations. Where the constraint cannot be removed, reset the line's target rate to the realistic capacity of the limiting station to avoid chasing an unattainable speed.
4Quellen
- Using Lean Manufacturing Approach for Improvement in Food Manufacturing: Case Study from Egypt (2024)Quelle öffnenVerlustzeit: 12,0 min · laut Bericht: “Unpacking cycle time”
Wörtliches Zitat anzeigen
This led to reduce the unpacking cycle time to 8 min instead of 12 min.
- Enhancing Production Efficiency and Quality in the Carbonated Beverage Industry: A Lean Manufacturing Approach (2024)Quelle öffnenMittlere Ereignisdauer: 21,2 min · laut Bericht: “Lotting cycle time”
Wörtliches Zitat anzeigen
Lotting cycle time (min) 21.2 18.4 -13.21%
- Enhancing Production Efficiency and Quality in the Carbonated Beverage Industry: A Lean Manufacturing Approach (2024)Quelle öffnenMittlere Ereignisdauer: 6,50 min · laut Bericht: “Spraying cycle time”
Wörtliches Zitat anzeigen
Sprying cicle time (min) 6.5 3.9 -40.00%
- Enhancing Production Efficiency and Quality in the Carbonated Beverage Industry: A Lean Manufacturing Approach (2024)Quelle öffnenMittlere Ereignisdauer: 18,4 min · laut Bericht: “Lotting cycle time”
Wörtliches Zitat anzeigen
Lotting cycle time (min) 21.2 18.4 -13.21%
- Enhancing Production Efficiency and Quality in the Carbonated Beverage Industry: A Lean Manufacturing Approach (2024)Quelle öffnenMittlere Ereignisdauer: 3,90 min · laut Bericht: “Spraying cycle time”
Wörtliches Zitat anzeigen
Sprying cicle time (min) 6.5 3.9 -40.00%

