foratvise
Loslegen
Rüsten und Einstellen

Tooling preparation and transport delay for changeover

Rüsten und EinstellenVerfügbarkeitFormen, Gießen und Dosieren

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei weniger als 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 57 % der Verlustzeit der Linie. Berichtet von 0 der 76 Studien, die sie beobachten konnten (spärliche Evidenz).

Was passiert

During a format or product changeover the required dies, molds or tooling for the press are not staged at the point of use, so operators must locate, retrieve and physically carry them from a storage area before the new setup can begin. This logistics step is performed as internal setup time, while the press remains stopped and waiting, extending the overall changeover duration.

Was man dagegen tut

Apply SMED principles by converting this logistics step into external setup: pre-stage the next job's tooling, carts and fixtures next to the press while the current run is still producing, using kitted tool trolleys, labeled storage locations and a standardized retrieval sequence. Schedule a dedicated handler or forklift pass synchronized with the production schedule so tooling arrives at the press before the machine is stopped.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
0,4 % [0,1–1,3 %]
Erwarteter Anteil an der Verlustzeit
0,2 % [0,0–0,7 %]
Anteil an der Verlustzeit bei Auftreten
57 % [45–67 %]
Studien / Einheiten
76 / 96
Evidenzgrad
D

Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    0,5 % [0,0–1,9 %]5 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    0,5 % [0,0–1,8 %]11 Studien
  • Bier, Wein und Spirituosen
    0,5 % [0,0–2,1 %]0 Studien
  • Backwaren und Teigwaren
    0,4 % [0,0–1,6 %]25 Studien
  • Fleisch, Geflügel und Fisch
    0,5 % [0,0–2,0 %]3 Studien
  • Obst- und Gemüseverarbeitung
    0,5 % [0,0–1,9 %]3 Studien
  • Getreide- und Ölsaatenmüllerei
    0,5 % [0,0–2,0 %]0 Studien
  • Zucker und Süßwaren
    0,5 % [0,0–1,9 %]8 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    0,5 % [0,0–1,8 %]7 Studien
  • Futtermittel und Heimtiernahrung
    0,5 % [0,0–1,9 %]6 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    0,5 % [0,0–2,1 %]8 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

During a format or product changeover the required dies, molds or tooling for the press are not staged at the point of use, so operators must locate, retrieve and physically carry them from a storage area before the new setup can begin. This logistics step is performed as internal setup time, while the press remains stopped and waiting, extending the overall changeover duration.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

The press shows an extended setup or idle machine-state with zero cycles and no active fault or alarm, preceding the first cycle of the new run. The pause duration correlates with operator presence/movement logs or manual changeover timestamps rather than with any equipment fault code, and the same transition recurs identically at every changeover between runs requiring different tooling.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Apply SMED principles by converting this logistics step into external setup: pre-stage the next job's tooling, carts and fixtures next to the press while the current run is still producing, using kitted tool trolleys, labeled storage locations and a standardized retrieval sequence. Schedule a dedicated handler or forklift pass synchronized with the production schedule so tooling arrives at the press before the machine is stopped.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Verlustzeit: 112 s · laut Bericht: “Prepare and transport tools to press”
    Wörtliches Zitat anzeigen
    14 Preparar y trasladar herramientas a la prensa 111,8 X