Transport/conveying system changeover adjustment
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei weniger als 1 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 55 % der Verlustzeit der Linie. Berichtet von 0 der 60 Studien, die sie beobachten konnten (spärliche Evidenz).
Was passiert
When switching to a different product or pan format on the baking line, the conveying and transfer elements (belts, transfer bars, lane guides, pan carriers) must be mechanically repositioned, exchanged or recalibrated to match the new product geometry. This mechanical reconfiguration and the subsequent trial runs to confirm smooth product handover between stages consume time between the last good unit of the previous run and the first good unit of the new run.
Was man dagegen tut
Apply SMED principles to the transport subsystem: pre-stage format-specific guide rails, transfer bars and pan carriers on quick-release mounts, use tool-less adjustment mechanisms with pre-set reference marks, and prepare changeover kits and checklists in advance so the mechanical reconfiguration is standardized and performed off-line wherever possible.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 0,4 % [0,1–1,3 %]
- Erwarteter Anteil an der Verlustzeit
- 0,2 % [0,0–0,7 %]
- Anteil an der Verlustzeit bei Auftreten
- 55 % [41–66 %]
- Studien / Einheiten
- 60 / 73
- Evidenzgrad
- D
Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.
2Wahrscheinlichkeit nach Segment
- Milchprodukte0,5 % [0,0–2,1 %]5 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte0,5 % [0,0–2,1 %]1 Studie
- Bier, Wein und Spirituosen0,5 % [0,0–2,2 %]0 Studien
- Backwaren und Teigwaren0,5 % [0,0–1,6 %]27 Studien
- Fleisch, Geflügel und Fisch0,5 % [0,0–2,1 %]2 Studien
- Obst- und Gemüseverarbeitung0,5 % [0,0–2,2 %]2 Studien
- Getreide- und Ölsaatenmüllerei0,5 % [0,0–2,2 %]0 Studien
- Zucker und Süßwaren0,5 % [0,0–1,9 %]8 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel0,5 % [0,0–2,0 %]4 Studien
- Futtermittel und Heimtiernahrung0,5 % [0,0–2,0 %]4 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)0,5 % [0,0–2,0 %]7 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseWhen switching to a different product or pan format on the baking line, the conveying and transfer elements (belts, transfer bars, lane guides, pan carriers) must be mechanically repositioned, exchanged or recalibrated to match the new product geometry. This mechanical reconfiguration and the subsequent trial runs to confirm smooth product handover between stages consume time between the last good unit of the previous run and the first good unit of the new run.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseMES/SCADA logs show the line or conveyor segment in a changeover or manual-adjustment state with no product flow, often accompanied by repeated manual jog commands on conveyor drives, guide-rail position changes, and intermittent start/stop cycles before the line stabilizes at target speed and the first good-unit count increments.
Gegenmaßnahme
Ingenieurpraktische HinweiseApply SMED principles to the transport subsystem: pre-stage format-specific guide rails, transfer bars and pan carriers on quick-release mounts, use tool-less adjustment mechanisms with pre-set reference marks, and prepare changeover kits and checklists in advance so the mechanical reconfiguration is standardized and performed off-line wherever possible.
4Quellen
- Modelo propuesto para la implementación de la metodología SMED en una empresa de alimentos de Santiago de Cali (2017)Quelle öffnenAnzahl der Ereignisse: 21,0 events · laut Bericht: “Transports”
Wörtliches Zitat anzeigen
Transportes 21 28:21

