foratvise
Loslegen
Formen, Backen und Garen

Backen

Baking of pan bread in a continuous tunnel oven

Validiertes ModellOEE-Grenze 0,917 [0,866–0,947]20.000 Monte-Carlo-Stichproben · Seed 20261115 · berechnet am 16. November 2026

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Backen kann höchstens 92 von je 100 geplanten Stunden nutzen. Der Rest entfällt auf Grenzen, die kein Werk vermeiden kann.

  1. 92höchstens nutzbar
  2. 8sind physikalische Grenze

Die drei Grenzen, die das festlegen

Laufzeit: bis 92 %

Der Rest sind Stillstände, die Physik oder Vorschrift erzwingen: Reinigung, Umrüsten, Abtauen.

Geschwindigkeit: bis 100 %

Wie nah an ihrer Höchstgeschwindigkeit sie laufen kann, ohne Produkt oder Anlage zu schädigen.

Gutprodukt: bis 100 %

Ein Teil des Produkts liegt auch bei gut beherrschtem Prozess außerhalb der Spezifikation.

Das technische Detail ansehen

Technisches Detail

Unsicherheitsintervalle, physikalische Modelle je Station und Quellen, für alle, die jede Zahl prüfen möchten.

1Szenario

Proofed wheat dough pieces in pans travel on the band of a continuous tunnel oven. Heat from the oven evaporates water at the surface, a crust forms and the evaporation front, held at the boiling point of water, drives heat by conduction (enhanced by evaporation and condensation inside the gas cells) into the crumb until its centre reaches the baked temperature. The loaves are sold as prepackaged products of 800 g nominal weight.

Herkunft der EingangsgrößenDeklarierte Annahme19Verifiziertes Zitat12

2Ergebnisse

Punktwert aus den Nominalparametern und 95-%-Intervall aus 20.000 Monte-Carlo-Ziehungen der unsicheren Parameter.
  • TheoretischThermodynamic minimum energy per kg of bread0 kJ/kg
  • Heat absorbed by the product without recovery (sensible + evaporation), per kg of bread411 [249–540] kJ/kg
  • Sensible heating of the dough, per kg of bread169 [127–170] kJ/kg
  • Evaporation of the bake loss, per kg of bread242 [113–379] kJ/kg
  • Best dokumentiertLowest documented monthly thermal energy of bakery ovens (products and moisture basis not stated; not like-for-like with the pan loaf)396 kJ/kg
  • TypischNormal electric energy use for baking (upper end)601 kJ/kg
  • Heat absorbed by the product over the lowest documented oven energy1,04 [0,63–1,36]
  • Latent heat of vaporisation of water at the boiling point2.256 kJ/kg
  • Specific heat of the dough (Siebel)2,31 [1,94–2,33] kJ/kg/K
  • Bake loss (share of dough mass evaporated)0,0968 [0,0477–0,1437]
  • TheoretischMaximum yield, bread per dough (by definition of product moisture)0,903 [0,856–0,952]
  • TheoretischMinimum bake time (crumb centre reaches the baked temperature)30,1 [19,5–45,3] min
  • Fourier number of the smallest half-dimension at the minimum bake time0,716 [0,568–0,836]
  • TheoretischMaximum bread throughput per square metre of oven band39,1 [25,2–62,5] kg/m²/h
  • Standard deviation of loaf weight6,47 [4,16–10,65] g
  • Smallest legal mean loaf weight800,0 [800,0–805,9] g
  • Overweight given away above the nominal quantity0,00000 [0,00000–0,00733]
  • Share of loaves with a deficiency beyond the tolerable negative error (allowed up to 2.5 %)0,0103 [0,0002–0,0250]
  • Share of loaves with a deficiency beyond twice the tolerable error (must be rejected)1,80 × 10⁻⁶ [2,83 × 10⁻¹³–3,77 × 10⁻⁴]
  • TheoretischMaximum OEE quality factor1,00000 [0,99962–1,00000]
  • TheoretischMaximum availability (daily cleaning and the heat-up it forces)0,917 [0,866–0,947]
  • Availability with declared changeover gaps0,885 [0,817–0,912]
  • TheoretischMaximum performance factor1,00
  • TheoretischPhysics-bounded OEE0,917 [0,866–0,947]
  • OEE with declared changeover gaps0,885 [0,817–0,912]

3Obergrenzen je Dimension

Jede Dimension zeigt die vom Modell berechneten Obergrenzen und, bei vergleichbaren Einheiten, dokumentierte Vergleichswerte. Farbe und Markerform kennzeichnen den Grenztyp im gesamten Orakel.
  • Theoretisch
  • Beste verfügbare Technik
  • Best dokumentiert
  • Typisch
Energie je ProdukteinheitkJ/kg · niedriger ist besser
  • TheoretischThermodynamic minimum energy per kg of bread0 kJ/kg
  • TheoretischDOE bandwidth study: products without significant chemical reactions have a zero thermodynamic minimum (bread is not covered by the study; the principle applies) · Vergleichswert0 kJ/kg
  • Best dokumentiertLowest documented monthly thermal energy of bakery ovens (products and moisture basis not stated; not like-for-like with the pan loaf)396 kJ/kg
  • TypischNormal electric energy use for baking, lower end · Vergleichswert450 kJ/kg
  • TypischNormal electric energy use for baking, upper end · Vergleichswert600 kJ/kg
  • TypischNormal electric energy use for baking (upper end)601 kJ/kg
Ausbeutehöher ist besser
  • TheoretischMaximum yield, bread per dough (by definition of product moisture)0,903 [0,856–0,952]
Zyklus- oder Verweilzeitmin · niedriger ist besser
  • TheoretischMinimum bake time (crumb centre reaches the baked temperature)30,1 [19,5–45,3] min
Durchsatzkg/m²/h · höher ist besser
  • TheoretischMaximum bread throughput per square metre of oven band39,1 [25,2–62,5] kg/m²/h
Qualitäthöher ist besser
  • TheoretischMaximum OEE quality factor1,00000 [0,99962–1,00000]
Verfügbarkeithöher ist besser
  • TheoretischMaximum availability (daily cleaning and the heat-up it forces)0,917 [0,866–0,947]
Leistunghöher ist besser
  • TheoretischMaximum performance factor1,00
OEEhöher ist besser
  • TheoretischPhysics-bounded OEE0,917 [0,866–0,947]

4Verlustkaskade

Was jede Obergrenze von der nächsten trennt, von der physikalischen Grenze bis zum typischen Betrieb.
  1. TheoretischBest dokumentiertEnergie je Produkteinheit
    0 kJ/kg → 396 kJ/kg (Abstand 396 kJ/kg)

    The thermodynamic minimum is zero because bread making involves no significant net chemical change: in the reversible limit the heat used to warm the dough and the latent heat carried away by the vapour would be recovered (the vapour condensed at 100 °C to preheat incoming dough, the hot loaf cooled against it). Without recovery the oven must deliver at least the heat absorbed by the product, the sensible heating of the dough plus the evaporation of the bake loss, which is slightly above the lowest documented monthly oven energy. That value is not like-for-like: the study does not state its products, loaf sizes or moisture basis, and a loaf or product with a smaller bake loss per kilogram (or a value per kilogram of dough) needs less heat than the 800 g pan loaf of this scenario; it is therefore not used as a bound.

  2. Best dokumentiertTypischEnergie je Produkteinheit
    396 kJ/kg → 601 kJ/kg (Abstand 205 kJ/kg)

    Real ovens lose heat with the flue gases and the extracted humid air, through walls and band returns, to the pans and the band that are reheated at every pass, and during idle running between products; the documented range spans almost a factor of twenty between ovens and cycles.

  3. TheoretischTypischZyklus- oder Verweilzeit

    The theoretical bake time holds the loaf surface at the boiling point from the first instant. In a real oven the surface first has to be heated to 100 °C by convection and radiation, the pan adds a resistance, and the colour of the crust (Maillard browning above 100 °C) may need a longer bake than the crumb does.

  4. TheoretischTypischQualität

    Weight scatter comes from the divider and from position-dependent bake loss; the legal rules force a mean above nominal when the scatter is large (giveaway) and require removal of loaves short by more than twice the tolerable error. Colour and moisture defects (under-baked crumb, burnt crust) are additional technology losses.

5Physikalisch begrenzte OEE

Die höchste OEE, die die Operation erreichen kann: Verfügbarkeit, Leistung und Qualität, begrenzt nur durch unvermeidbare Stillstände und physikalische Prozessfähigkeit.
Anteil der Belegungszeit, der nach jedem unvermeidbaren Verlust verbleibt. Die Achse beginnt bei 0,80.
  • Belegungszeit (ideal)
    1,000
  • Verfügbarkeit
    Faktor 0,917 [0,866–0,947]
    0,917 (−0,083)
  • Leistung
    Faktor 1,00
    0,917 (−0,000)
  • Qualität
    Faktor 1,00000 [0,99962–1,00000]
    0,917 (−0,000)
  • Physikalisch begrenzte OEE
    0,917 [0,866–0,947]

6Vollständige Herleitung

Massen- und Energiebilanzen, geschwindigkeitsbestimmender Schritt, Prozessfähigkeit und unvermeidbare Stillstände, mit Erläuterung jedes Terms.

Scope. Proofed wheat dough in pans, baked on the band of a continuous tunnel oven and sold as a prepackaged loaf of 800 g nominal weight. Symbols, values, units, uncertainty distributions and sources are listed in the parameter table generated from config/physics/baking.yaml.

1. Mass balance — maximum yield

In the oven the dough loses water: the surface dries into a crust and vapour leaves through the oven exhaust. Carbon dioxide and ethanol produced by fermentation also leave, but their mass is small and is neglected, so the dry matter is conserved. If xdx_d is the moisture content of the dough and xbx_b that of the cooled loaf (both on a wet basis), a dough mass mdm_d contains md(1−xd)m_d(1 - x_d) of dry matter, which becomes a loaf of mass mb=md(1−xd)/(1−xb)m_b = m_d(1 - x_d)/(1 - x_b). The yield and the bake loss are therefore

Y=mbmd=1−xd1−xb,BL=1−Y.Y = \frac{m_b}{m_d} = \frac{1 - x_d}{1 - x_b}, \qquad BL = 1 - Y .

The bake loss is not a loss in the sense of OEE: it is required to form the crust and to reach the moisture that defines the product. The yield ceiling is fixed by definition of the product moisture; any further loss (dough stuck to pans, crippled loaves, crumbs) is technology. Neither dough nor bread moisture has an open legal limit in the registered sources (the Spanish bread quality standard of 2019 explicitly removed its moisture limits), so both are declared scenario values with uncertainty ranges.

2. Energy balance — minimum energy per unit of product

Thermodynamic minimum. Baking involves no significant net chemical change (starch gelatinisation, protein coagulation and browning reactions have small free-energy changes). In the reversible limit the heat used to warm the dough would be recovered by cooling the loaf against incoming dough, and the latent heat carried away by the vapour would be recovered by condensing it at 100 °C. The thermodynamic minimum is therefore zero, in line with the principle stated by the US DOE bandwidth study that products without significant chemical reactions have a zero thermodynamic minimum (bread itself is not covered by that study).

Heat absorbed by the product without recovery. An oven that does not recover heat must deliver at least the heat absorbed by the product. Per kilogram of dough it is the sensible heating of the whole piece from the oven-entry temperature T0T_0 to the baked crumb temperature TcT_c plus the evaporation of the bake loss; per kilogram of bread it is divided by YY:

qprod=cp,d (Tc−T0)+BL  hfg(Tb)Y.q_{prod} = \frac{c_{p,d}\,(T_c - T_0) + BL\; h_{fg}(T_b)}{Y}.

Here cp,dc_{p,d} is the specific heat of the dough and hfg(Tb)h_{fg}(T_b) the latent heat of vaporisation of water at its boiling point TbT_b at atmospheric pressure (latent heat and boiling point from IAPWS through CoolProp); the whole bake loss is taken to evaporate at the boiling point, and the crust, which is thin and hotter than the crumb, is neglected. The specific heat follows Siebel's formula for unfrozen foods, cp,d=aSxd+bSc_{p,d} = a_S x_d + b_S, in which aSxda_S x_d is the contribution of the water and bSb_S that of the solids. The DOE study prints bS=0.84b_S = 0.84 kJ kg⁻¹ K⁻¹ in its frozen-food expression and 0.48 in its unfrozen one; since the solids do not change phase the two should be equal, so the point value is 0.84 and the uncertainty range spans both printed values. The gelatinisation enthalpy of starch is neglected because no open source with a value was found; it would add to qprodq_{prod}.

The energy ceilings. Theoretical: 0. Documented: the lowest monthly thermal energy measured in a two-year study of 51 bakery ovens, 0.110 kWh per kg. Typical: the upper end of the normal electric energy use for baking, 0.167 kWh per kg (600 kJ/kg). The highest monthly thermal value of the same study (2 kWh/kg) and the lower end of the electric range are listed as benchmarks. For the scenario loaf, qprodq_{prod} is slightly above the lowest documented monthly value (the output product_heat_over_documented is their ratio). The documented value is therefore not like-for-like and is not compared with the bound (compare: false): the study does not state its products, loaf sizes or moisture basis, and a product with a smaller bake loss per kilogram (low-moisture goods, larger loaves) or a value expressed per kilogram of dough needs less heat than the 800 g pan loaf of this scenario. No best-available-technique value is computed, because no open source documents one for this product.

3. Rate-limiting step — minimum bake time and maximum throughput

As soon as the surface of the dough reaches the boiling point of water, it starts to dry and an evaporation front forms; beneath it the moist crumb cannot exceed the boiling point TbT_b while it still holds liquid water. The front therefore acts as a boundary held at TbT_b that drives heat into the crumb. Inside the crumb, heat moves by conduction through the solid matrix and, much faster, by evaporation of water on the warm side of each gas cell and its condensation on the cold side; both are lumped into an effective thermal diffusivity αeff\alpha_{eff}, several times larger than the molecular diffusivity of dense foods. No open source gives its value, so it is a declared scenario parameter with a wide range.

The loaf is modelled as a rectangular brick of half-dimensions ℓx,ℓy,ℓz\ell_x, \ell_y, \ell_z whose surface is held at TbT_b from the start. The exact solution of the heat equation at the centre is the product of three slab solutions,

θ(t)=Tb−TcentreTb−T0=∏i∈{x,y,z}∑m≥04(−1)m(2m+1)πexp⁡ ⁣(−λm2 αeff tℓi2),λm=(2m+1)π2,\theta(t) = \frac{T_b - T_{centre}}{T_b - T_0} = \prod_{i\in\{x,y,z\}} \sum_{m\ge0} \frac{4(-1)^m}{(2m+1)\pi}\exp\!\left(-\lambda_m^2\,\frac{\alpha_{eff}\,t}{\ell_i^2}\right), \qquad \lambda_m = \frac{(2m+1)\pi}{2},

where each factor is the dimensionless centre temperature of an infinite slab as a function of its Fourier number Foi=αefft/ℓi2Fo_i = \alpha_{eff} t/\ell_i^2, the ratio between the time elapsed and the time heat needs to diffuse over the half-thickness. The loaf is baked when the crumb centre reaches TcT_c, i.e. when θ=(Tb−Tc)/(Tb−T0)\theta = (T_b - T_c)/(T_b - T_0); the minimum bake time tbaket_{bake} is found by bisection. It is a lower bound because in a real oven the surface first has to be heated to the boiling point by convection and radiation through the pan.

Maximum throughput per square metre of band. A loaf of mass wˉ\bar w occupies a footprint LxLy/ϕL_x L_y/\phi of band, where ϕ\phi is the share of the band covered by loaves; each square metre is occupied for tbaket_{bake}, so

m˙max′′=wˉ ϕLxLy tbake.\dot m''_{max} = \frac{\bar w\,\phi}{L_x L_y\, t_{bake}}.

4. Process capability — quality ceiling

The loaf weight varies because the divider scatters the dough piece weight (σdiv\sigma_{div}, transmitted as YσdivY\sigma_{div}) and because the bake loss differs with position on the band and oven non-uniformity (σBL\sigma_{BL}, transmitted as md σBLm_d\,\sigma_{BL}):

σw2=(Y σdiv)2+(md σBL)2,md=wˉ/Y.\sigma_w^2 = (Y\,\sigma_{div})^2 + (m_d\,\sigma_{BL})^2, \qquad m_d = \bar w / Y.

The legal rules for prepackages (Directive 76/211/EEC and OIML R 87) state that the actual contents must not be less, on average, than the nominal quantity QnQ_n; that a lot may contain no more than 2.5 % of packages short by more than the tolerable negative error TT (T1 errors); and that no package may be short by more than 2T2T (T2 errors). For 500 g to 1 000 g, TT = 15 g. The smallest legal mean weight is

wˉ=max⁡(Qn,  Qn−T+z0.975 σw),z0.975=Φ−1(1−0.025)=1.96.\bar w = \max\big(Q_n,\; Q_n - T + z_{0.975}\,\sigma_w\big), \qquad z_{0.975} = \Phi^{-1}(1 - 0.025) = 1.96 .

The overweight given away is (wˉ−Qn)/Qn(\bar w - Q_n)/Q_n. The share of T1 errors is Φ((Qn−T−wˉ)/σw)\Phi\big((Q_n - T - \bar w)/\sigma_w\big), and loaves with T2 errors, Φ((Qn−2T−wˉ)/σw)\Phi\big((Q_n - 2T - \bar w)/\sigma_w\big), must be rejected by the checkweigher; they are the quality loss counted here:

Qmax=1−Φ ⁣(Qn−2T−wˉσw).Q_{max} = 1 - \Phi\!\left(\frac{Q_n - 2T - \bar w}{\sigma_w}\right).

Colour and moisture defects (pale or burnt crust, under-baked crumb) are additional losses of the technology; the moisture of the product is part of its definition (section 1).

5. Unavoidable stops — maximum availability

Over a production period tpert_{per} the oven loses the daily cleaning of band and pans (tclt_{cl}; crumbs, flour and release oil carbonise) and the time needed to heat its refractory and steel mass from cold after it (thut_{hu}):

Amax=1−thu+tcltper=0.917.A_{max} = 1 - \frac{t_{hu} + t_{cl}}{t_{per}} = 0.917 .

The oven is cleaned dry and by hand, not in place, so the cleaning model does not apply and both durations are declared scenario values. The empty-band gap tgapt_{gap} at each of the ncon_{co} product changeovers, while the zone temperatures settle to a new profile, is a decision of the product mix, not physics; it enters only Ascen=Amax−nco tgap/tperA_{scen} = A_{max} - n_{co}\,t_{gap}/t_{per} = 0.885 and oee_scenario.

6. Physics-bounded OEE

Scope of the bound. The theoretical label of OEEmaxOEE_{max} means physics-bounded under the declared scenario: the ceiling follows from the physics of the operation for the declared product, equipment and schedule, and it is a bound only conditional on those declarations. It follows the common definition of all models: AmaxA_{max} counts only stops required by regulation or forced by a physical mechanism, at their physical minimum duration, plus the start-up they force; PmaxP_{max} is the ratio of the physics-limited ideal cycle to the cycle of the capable process; QmaxQ_{max} is the share of conforming units, and mass losses of conforming product are reported only as yield.

OEEmax=Amax×Pmax×Qmax,Pmax=1.OEE_{max} = A_{max} \times P_{max} \times Q_{max}, \qquad P_{max} = 1.

Pmax=1P_{max} = 1 refers to the conduction-limited bake time of section 3. The yield ceiling YY is reported separately and does not enter the OEE, because the bake loss is part of the definition of the product. The point values and Monte Carlo intervals over the declared uncertainty of every input are reported in the output table.

7. Assumptions and validity

See the assumption and validity lists generated from the configuration file. The dough specific heat and the effective diffusivity of the crumb are the properties that could later be supplied by a composition-based property model. The most influential inputs (sensitivity table) are the two moisture contents for energy and yield, the effective diffusivity and the loaf dimensions for the bake time, and the cleaning and heat-up times for availability.

References

  • European Commission, Joint Research Centre. Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries, 2019 (section 16.2, bakery goods).
  • U.S. Department of Energy. Bandwidth Study on Energy Use and Potential Energy Saving Opportunities in U.S. Food and Beverage Manufacturing, 2017.
  • Council Directive 76/211/EEC on the making-up by weight or by volume of certain prepackaged products, consolidated text of 11.04.2009.
  • International Organization of Legal Metrology. OIML R 87 Quantity of product in prepackages, Edition 2016.
  • Bell, I. H., Wronski, J., Quoilin, S., Lemort, V. (2014). Pure and pseudo-pure fluid thermophysical property evaluation and the open-source thermophysical property library CoolProp. Industrial & Engineering Chemistry Research, 53, 2498–2508. doi:10.1021/ie4033999

7Parameter und Herkunft

Jede Eingangsgröße mit Wert, Einheit, Rolle, Unsicherheitsverteilung und Herkunft. Öffnen Sie ein Zitat, um die Quellenpassage zu lesen, die den Wert belegt.
  • xdx_d0,44

    Moisture content of the dough (wet basis)

    Szenario · Gleichverteilt 0,42 bis 0,46

    Deklarierte Annahme

    Recipe-dependent (flour moisture and water absorption); no open source with a value was found. Declared assumption; replace with the plant's dough formula.

  • xbx_b0,38

    Moisture content of the cooled loaf (wet basis), a product specification

    Szenario · Gleichverteilt 0,36 bis 0,4

    Deklarierte Annahme

    Product specification; no open legal limit exists in the registered sources (the Spanish bread quality standard of 2019 removed its moisture limits). Declared assumption.

  • aSa_S3,35 kJ/kg/K

    Siebel coefficient of moisture in the specific heat of an unfrozen food

    Stoffwert · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    −26(3.35𝑎𝑎+ 0.48)Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (öffnet in neuem Tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. S. 55. DOE/EE-1571; OSTI ID 1512366
  • bSb_S0,84 kJ/kg/K

    Constant term of Siebel's specific heat (contribution of the solids, the same above and below freezing)

    Stoffwert · Gleichverteilt 0,48 bis 0,84 kJ/kg/K

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    −17(1.26𝑎𝑎+ 0.84)Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (öffnet in neuem Tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. S. 55. DOE/EE-1571; OSTI ID 1512366
  • T0T_030 °C

    Dough temperature entering the oven (end of proofing)

    Technik · Gleichverteilt 30 bis 35 °C

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    This is usually accomplished at 30–35 °C and at 85 % relative humidity.Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 628. EUR 29978 EN; JRC118627; doi:10.2760/243911
  • TcT_c96 °C

    Crumb-centre temperature at which the loaf is baked (starch gelatinised, structure set)

    Szenario · Gleichverteilt 92 bis 98 °C

    Deklarierte Annahme

    No open source with a value was found; declared assumption below the boiling point that bounds the crumb temperature.

  • edoce_{doc}0,11 kW·h/kg

    Lowest monthly thermal energy measured on bakery ovens (51 ovens, two-year study)

    Vergleichswert · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    The monthly measured thermic values can range between 0.110 kWh/kg and 2 kWh/kg, as observed in a two-year study on 51 different ovens.Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 628. EUR 29978 EN; JRC118627; doi:10.2760/243911
  • etype_{typ}0,167 kW·h/kg

    Normal electric energy use for baking, upper end

    Vergleichswert · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    The electric energy usage for baking normally ranges from 0.125 kWh to 0.167 kWh per kg of product (450 – 600 kJ/kg)Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 628. EUR 29978 EN; JRC118627; doi:10.2760/243911
  • αeff\alpha_{eff}1,20 × 10⁻⁶ m²/s

    Effective thermal diffusivity of the crumb during baking (conduction plus evaporation–condensation in the gas cells)

    Stoffwert · Gleichverteilt 8,00 × 10⁻⁷ bis 1,60 × 10⁻⁶ m²/s

    Deklarierte Annahme

    No open source with a value was found. Declared assumption; it is several times the molecular diffusivity of dense foods because vapour evaporates on the warm side of each gas cell and condenses on the cold side (derivation, section 3). Replace with a value fitted to a measured crumb-centre temperature curve.

  • LxL_x0,26 m

    Loaf length

    Szenario · Fest

    Deklarierte Annahme

    Pan dimensions of an 800 g sandwich loaf; declared assumption.

  • LyL_y0,11 m

    Loaf width

    Szenario · Fest

    Deklarierte Annahme
  • LzL_z0,12 m

    Loaf height

    Szenario · Fest

    Deklarierte Annahme
  • ϕ\phi0,7

    Share of the band area covered by loaves (pan straps and gaps)

    Szenario · Gleichverteilt 0,6 bis 0,8

    Deklarierte Annahme
  • QnQ_n800 g

    Nominal quantity of the prepackaged loaf

    Szenario · Fest

    Deklarierte Annahme
  • TT15 g

    Tolerable negative error (tolerable deficiency) for a nominal quantity from 500 g to 1 000 g

    Regulatorisch · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    from 500 to 1 000 — 15 from 1 000 to 10 000 1.5Council Directive 76/211/EEC of 20 January 1976 on the approximation of the laws of the Member States relating to the making-up by weight or by volume of certain prepackaged products (consolidated text 11.04.2009) (öffnet in neuem Tab). Publications Office of the European Union, 2009. S. 5. CELEX 01976L0211-20090411
  • pT1p_{T1}0,025

    Maximum share of prepackages with a deficiency beyond the tolerable error

    Regulatorisch · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    A homogenous group of prepackages shall contain no more than 2.5 % of packages having T1 errors.OIML R 87 Quantity of product in prepackages, Edition 2016 (E) (öffnet in neuem Tab). International Organization of Legal Metrology, 2016. S. 13. OIML R 87:2016 (E)
  • σdiv\sigma_{div}6 g

    Standard deviation of the dough piece weight from the divider

    Technik · Gleichverteilt 3 bis 10 g

    Deklarierte Annahme

    Capability assumption; replace with the divider's measured weight distribution.

  • σBL\sigma_{BL}0,004

    Standard deviation of the bake loss between loaves (fraction of dough mass), from position on the band and oven non-uniformity

    Technik · Gleichverteilt 0,002 bis 0,008

    Deklarierte Annahme

    Capability assumption.

  • tpert_{per}24 h

    Calendar period of the availability balance (one production day)

    Szenario · Fest

    Deklarierte Annahme
  • thut_{hu}1 h

    Heat-up of the oven from cold to baking temperatures

    Szenario · Gleichverteilt 0,5 bis 1,5 h

    Deklarierte Annahme

    Set by the thermal mass of the oven and the burner power; declared assumption.

  • tclt_{cl}1 h

    Cleaning of band

    Szenario · Gleichverteilt 0,5 bis 2 h

    Deklarierte Annahme
  • ncon_{co}3

    Product changeovers per day

    Szenario · Fest

    Deklarierte Annahme
  • tgapt_{gap}15 min

    Empty-band gap per changeover while zone temperatures settle to the new profile

    Szenario · Gleichverteilt 10 bis 30 min

    Deklarierte Annahme

8Vergleichswerte

Dokumentierte Werte aus offenen Quellen zur Prüfung der Obergrenzen; kein dokumentierter Wert darf die theoretische Grenze übertreffen.
VergleichswertObergrenzeWertHerkunft
DOE bandwidth study: products without significant chemical reactions have a zero thermodynamic minimum (bread is not covered by the study; the principle applies)
Wörtliches Zitat anzeigen
Most food and beverage products have a zero TM energy intensity because there are no significant chemical reactions involved.Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (öffnet in neuem Tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. S. 25. DOE/EE-1571; OSTI ID 1512366
Theoretisch0 kJ/kgVerifiziertes Zitat
Lowest monthly measured thermal energy of bakery ovens (51 ovens, two years). Not like-for-like with the pan-bread scenario: the products, loaf sizes and the moisture basis of the study are not stated, and the value is below the heat an 800 g pan loaf with a 10 % bake loss absorbs without recovery; it fits products with a smaller bake loss per kg (low-moisture goods, larger loaves) or a per-kg-of-dough basis
Wörtliches Zitat anzeigen
The monthly measured thermic values can range between 0.110 kWh/kg and 2 kWh/kg, as observed in a two-year study on 51 different ovens.Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 628. EUR 29978 EN; JRC118627; doi:10.2760/243911
Best dokumentiert0,11 kW·h/kgVerifiziertes Zitat
Highest monthly measured thermal energy of bakery ovens (upper end of the range, poorest ovens and cycles)
Wörtliches Zitat anzeigen
The monthly measured thermic values can range between 0.110 kWh/kg and 2 kWh/kg, as observed in a two-year study on 51 different ovens.Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 628. EUR 29978 EN; JRC118627; doi:10.2760/243911
Typisch2 kW·h/kgVerifiziertes Zitat
Normal electric energy use for baking, lower end
Wörtliches Zitat anzeigen
The electric energy usage for baking normally ranges from 0.125 kWh to 0.167 kWh per kg of product (450 – 600 kJ/kg)Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 628. EUR 29978 EN; JRC118627; doi:10.2760/243911
Typisch450 kJ/kgVerifiziertes Zitat
Normal electric energy use for baking, upper end
Wörtliches Zitat anzeigen
The electric energy usage for baking normally ranges from 0.125 kWh to 0.167 kWh per kg of product (450 – 600 kJ/kg)Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 628. EUR 29978 EN; JRC118627; doi:10.2760/243911
Typisch600 kJ/kgVerifiziertes Zitat

9Unvermeidbare Stillstände

Stillstände, die Physik oder Regulierung erzwingen; sie bestimmen die maximale Verfügbarkeit.
  • Oven heat-upDeklarierte Annahme

    The refractory and steel mass of a tunnel oven must be brought to baking temperature before the first loaf enters; the time is the thermal mass times the temperature rise divided by the burner power.

  • Cleaning of band and pansDeklarierte Annahme

    Crumbs, flour and release oil accumulate on the band and pans and carbonise; daily removal is assumed.

  • Empty band at changeovers (scenario stop: availability_scenario only)Deklarierte Annahme

    A product with another bake time or temperature profile cannot share the oven zones with the previous product; the band runs empty while the zones settle.

10Annahmen

  1. Availability: the daily cleaning of band and pans (carbonising residues) and the oven heat-up it forces are counted at their declared durations; the oven is cleaned dry and by hand, not in place, so the cleaning model does not apply. Empty-band gaps at product changeovers are a product-mix decision and enter only availability_scenario and oee_scenario.
  2. Dry matter is conserved: carbon dioxide and ethanol lost in the oven are neglected, so the bake loss is water and follows from the two moisture contents.
  3. The dough specific heat follows Siebel's formula for unfrozen foods; the whole piece is heated to the baked crumb temperature (the hotter, thin crust is neglected) and the bake loss evaporates at the boiling point; the starch gelatinisation enthalpy is neglected because no open source with a value was found.
  4. The loaf is a rectangular brick with constant effective diffusivity whose surface is held at the boiling point at 1 atm from the start (the evaporation front); the computed bake time is a lower bound.
  5. Loaf weights are normally distributed; the mean is the smallest value that satisfies the average requirement and the 2.5 % limit on T1 errors; loaves with T2 errors are rejected and count as quality losses; the giveaway is reported separately.

11Gültigkeitsbereich

  • Wheat pan breads of 400 g to 1 000 g baked in continuous tunnel ovens at atmospheric pressure.

12Sensitivität

Elastizität: relative Änderung der Ergebnisgröße bei relativer Änderung jedes Parameters. Daneben steht die Spearman-Rangkorrelation aus den Monte-Carlo-Ziehungen.
  • tpert_{per}Calendar period of the availability balance (one production day)
    Elastizität +0,091Spearman-ρ —
  • thut_{hu}Heat-up of the oven from cold to baking temperatures
    Elastizität -0,045Spearman-ρ -0,53
  • tclt_{cl}Cleaning of band
    Elastizität -0,045Spearman-ρ -0,83
  • TTTolerable negative error (tolerable deficiency) for a nominal quantity from 500 g to 1 000 g
    Elastizität 0,000Spearman-ρ —
  • σdiv\sigma_{div}Standard deviation of the dough piece weight from the divider
    Elastizität 0,000Spearman-ρ 0,00
  • xdx_dMoisture content of the dough (wet basis)
    Elastizität 0,000Spearman-ρ +0,01
  • QnQ_nNominal quantity of the prepackaged loaf
    Elastizität 0,000Spearman-ρ —
  • σBL\sigma_{BL}Standard deviation of the bake loss between loaves (fraction of dough mass), from position on the band and oven non-uniformity
    Elastizität 0,000Spearman-ρ 0,00
  • xbx_bMoisture content of the cooled loaf (wet basis), a product specification
    Elastizität 0,000Spearman-ρ -0,02
  • Größe steigt mit dem Parameter
  • Größe sinkt mit dem Parameter

13Validierungsprüfungen

Ein Modell wird nur veröffentlicht, wenn alle Prüfungen bestanden sind.
  • Dimensionsanalyse25 outputs converted to their declared unitsBestanden
  • Jeder zitierte Wert an seiner Quelle verifiziert12 verified, 0 failedBestanden
  • Kein dokumentierter Wert übertrifft die theoretische GrenzeBestanden
  • Obergrenzen in physikalischer ReihenfolgeBestanden
  • Anteile zwischen 0 und 1Bestanden

14Verlustursachen in dieser Operation

Wahrscheinlichkeit, dass jede Ursache als relevanter Verlust einer Linie dokumentiert ist, gepoolt über alle Segmente.

15Literatur

  1. Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 628. EUR 29978 EN; JRC118627; doi:10.2760/243911
  2. Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (öffnet in neuem Tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. S. 55. DOE/EE-1571; OSTI ID 1512366
  3. Council Directive 76/211/EEC of 20 January 1976 on the approximation of the laws of the Member States relating to the making-up by weight or by volume of certain prepackaged products (consolidated text 11.04.2009) (öffnet in neuem Tab). Publications Office of the European Union, 2009. S. 5. CELEX 01976L0211-20090411
  4. OIML R 87 Quantity of product in prepackages, Edition 2016 (E) (öffnet in neuem Tab). International Organization of Legal Metrology, 2016. S. 13. OIML R 87:2016 (E)
  5. doi:10.1021/ie4033999 — Thermophysical property library (latent heat and boiling point of water).

Prozesse mit dieser Operation