foratvise
Loslegen
Anlagenausfall (Störungen)

Tray Corner Ear Flare Defect

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei etwa 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 57 % der Verlustzeit der Linie. Berichtet von 1 der 112 Studien, die sie beobachten konnten (spärliche Evidenz).

Was passiert

Worn, misaligned or improperly set folding tooling (fold bars, mandrels or creasing blades) in the tray folding unit fails to fully compress and crease the corner ear of the tray blank, so the folded flap springs back open instead of lying flat against the side wall. The flared ear then catches on downstream guides or forming surfaces, causing tray jams and mechanical faults that require intervention to clear and realign the tooling.

Was man dagegen tut

Inspect and replace worn fold bars, mandrels or creasing blades, and verify the alignment and pressure setting of the folding station against the tooling specification. Implement a periodic preventive maintenance check on the ear-folding mechanism and confirm incoming blank quality (score lines, material stiffness) is within tolerance to ensure a clean, flat fold.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
0,6 % [0,1–1,6 %]
Erwarteter Anteil an der Verlustzeit
0,3 % [0,1–0,9 %]
Anteil an der Verlustzeit bei Auftreten
57 % [46–68 %]
Studien / Einheiten
112 / 155
Evidenzgrad
D

Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    0,6 % [0,1–2,3 %]14 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    0,8 % [0,1–2,5 %]33 Studien
  • Bier, Wein und Spirituosen
    0,6 % [0,1–2,2 %]14 Studien
  • Backwaren und Teigwaren
    0,7 % [0,1–2,6 %]6 Studien
  • Fleisch, Geflügel und Fisch
    0,7 % [0,1–2,5 %]6 Studien
  • Obst- und Gemüseverarbeitung
    0,7 % [0,1–2,7 %]4 Studien
  • Getreide- und Ölsaatenmüllerei
    0,7 % [0,1–2,4 %]4 Studien
  • Zucker und Süßwaren
    0,7 % [0,1–2,6 %]4 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    0,7 % [0,1–2,4 %]8 Studien
  • Futtermittel und Heimtiernahrung
    0,7 % [0,1–2,4 %]5 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    0,6 % [0,1–2,3 %]14 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

Worn, misaligned or improperly set folding tooling (fold bars, mandrels or creasing blades) in the tray folding unit fails to fully compress and crease the corner ear of the tray blank, so the folded flap springs back open instead of lying flat against the side wall. The flared ear then catches on downstream guides or forming surfaces, causing tray jams and mechanical faults that require intervention to clear and realign the tooling.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

SCADA/MES logs show recurrent fault or jam alarms localized to the tray folding or ear-forming station, with downtime events attributed to that station rather than a general line stop. Fault counters at the folding axis or servo increase, cycle time or station dwell time shows irregular spikes, and downstream units may register starvation while the jam is cleared.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Inspect and replace worn fold bars, mandrels or creasing blades, and verify the alignment and pressure setting of the folding station against the tooling specification. Implement a periodic preventive maintenance check on the ear-folding mechanism and confirm incoming blank quality (score lines, material stiffness) is within tolerance to ensure a clean, flat fold.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Anzahl der Ereignisse: 30,0 events · laut Bericht: “Tray ear flare”
    Wörtliches Zitat anzeigen
    ความสูญเสียหลักเกิดจากปัญหาหูถาดอ้า ซึ่งมีความถี่ในการเกิดสูงสุดถึง 30 ครั้ง (เฉลี่ย 2.50 ครั้งต่อเดือน)