foratvise
Loslegen
Anlagenausfall (Störungen)

Tumbler shaft/body breakage

Anlagenausfall (Störungen)VerfügbarkeitMischen und Vermengen

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei etwa 1 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 58 % der Verlustzeit der Linie. Berichtet von 1 der 31 Studien, die sie beobachten konnten (spärliche Evidenz).

Was passiert

Repeated cyclic torque and bending loads on the tumbler drive shaft, combined with product load imbalance, fatigue the shaft or structural welds until they fracture, causing the whole tumbler body or its drive shaft to break. Corrosion, wear of bearings or support bushings, and overloading beyond rated capacity accelerate the fatigue process and can trigger sudden catastrophic breakage.

Was man dagegen tut

Implement periodic non-destructive inspection (visual and ultrasonic/dye penetrant) of the shaft and welds, monitor vibration and torque trends to detect fatigue cracks before failure, and enforce load limits with balanced loading procedures. Replace shafts and bearings on a condition-based or preventive schedule using materials and dimensions rated for the actual operating loads.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
1,0 % [0,2–3,1 %]
Erwarteter Anteil an der Verlustzeit
0,6 % [0,1–1,8 %]
Anteil an der Verlustzeit bei Auftreten
58 % [47–68 %]
Studien / Einheiten
31 / 40
Evidenzgrad
D

Grad D: 0 oder 1 Studie; die Schätzung beruht auf partiellem Pooling und Priori-Verteilungen, und das breite Intervall ist das Ergebnis.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    1,1 % [0,1–4,4 %]6 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    1,2 % [0,1–4,8 %]2 Studien
  • Bier, Wein und Spirituosen
    1,2 % [0,1–4,8 %]0 Studien
  • Backwaren und Teigwaren
    1,1 % [0,1–4,5 %]2 Studien
  • Fleisch, Geflügel und Fisch
    1,8 % [0,2–7,6 %]1 Studie
  • Obst- und Gemüseverarbeitung
    1,2 % [0,1–4,8 %]2 Studien
  • Getreide- und Ölsaatenmüllerei
    1,2 % [0,1–4,6 %]0 Studien
  • Zucker und Süßwaren
    1,2 % [0,1–4,5 %]3 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    1,2 % [0,1–4,7 %]3 Studien
  • Futtermittel und Heimtiernahrung
    1,1 % [0,1–4,3 %]5 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    1,2 % [0,1–4,5 %]7 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

Repeated cyclic torque and bending loads on the tumbler drive shaft, combined with product load imbalance, fatigue the shaft or structural welds until they fracture, causing the whole tumbler body or its drive shaft to break. Corrosion, wear of bearings or support bushings, and overloading beyond rated capacity accelerate the fatigue process and can trigger sudden catastrophic breakage.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

Motor current or torque trace on the tumbler drive shows an abrupt spike followed by a drop to near zero or a sudden stop fault, often with a drive overcurrent or mechanical fault alarm. The machine state log shows an unplanned transition to stopped/fault state with no preceding slow-down trend, and downstream feed to the line is interrupted while upstream buffers fill.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Implement periodic non-destructive inspection (visual and ultrasonic/dye penetrant) of the shaft and welds, monitor vibration and torque trends to detect fatigue cracks before failure, and enforce load limits with balanced loading procedures. Replace shafts and bearings on a condition-based or preventive schedule using materials and dimensions rated for the actual operating loads.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Verlustzeit: 33,0 min · laut Bericht: “Tumbler breakage”
    Wörtliches Zitat anzeigen
    Corrective maintenance time 33 min - 102 min - 40 min 20 min
  2. Verlustzeit: 102 min · laut Bericht: “Tumbler shaft breakage”
    Wörtliches Zitat anzeigen
    Corrective maintenance time 33 min - 102 min - 40 min 20 min