foratvise
Loslegen
Mischen und Rezeptieren

Mischen und Vermengen

Batch blending of miscible liquids in a baffled stirred tank

Validiertes ModellOEE-Grenze 0,968 [0,855–0,983]20.000 Monte-Carlo-Stichproben · Seed 20261115 · berechnet am 16. November 2026

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Mischen und Vermengen kann höchstens 97 von je 100 geplanten Stunden nutzen. Der Rest entfällt auf Grenzen, die kein Werk vermeiden kann.

  1. 97höchstens nutzbar
  2. 3sind physikalische Grenze

Die drei Grenzen, die das festlegen

Laufzeit: bis 98 %

Der Rest sind Stillstände, die Physik oder Vorschrift erzwingen: Reinigung, Umrüsten, Abtauen.

Geschwindigkeit: bis 100 %

Wie nah an ihrer Höchstgeschwindigkeit sie laufen kann, ohne Produkt oder Anlage zu schädigen.

Gutprodukt: bis 98 %

Ein Teil des Produkts liegt auch bei gut beherrschtem Prozess außerhalb der Spezifikation.

Das technische Detail ansehen

Technisches Detail

Unsicherheitsintervalle, physikalische Modelle je Station und Quellen, für alle, die jede Zahl prüfen möchten.

1Szenario

A beverage or dairy formulation is prepared in a 10 m3 baffled, flat-bottomed cylindrical tank with liquid height equal to the tank diameter and a single axial-flow impeller. A concentrate (syrup, flavour base) is dosed into water or milk and blended until the composition is uniform within specification; the batch is then pumped out, the tank drains by gravity and the next batch is filled. Incompatible products are separated by a cleaning-in-place.

Herkunft der EingangsgrößenBerechnet1Deklarierte Annahme17Verifiziertes Zitat5Nur Referenz1

2Ergebnisse

Punktwert aus den Nominalparametern und 95-%-Intervall aus 20.000 Monte-Carlo-Ziehungen der unsicheren Parameter.
  • Tank diameter (liquid height equal to diameter)2,34 m
  • Impeller speed at the installed power per volume106 [72–199] 1/min
  • Impeller Reynolds number724.267 [333.147–1.214.477]
  • Impeller tip speed4,26 [3,29–6,42] m/s
  • Blend time to 95 % homogeneity with the large impeller (D/T of the best geometry)21,7 [16,0–26,3] s
  • Blend time to 95 % homogeneity with the installed impeller24,9 [17,9–30,9] s
  • TheoretischMinimum blend time to the specification homogeneity (large impeller)47,0 [31,9–57,3] s
  • TypischBlend time to the specification homogeneity (installed impeller)54,0 [36,2–67,2] s
  • Batch cycle time with the large impeller (fill + blend + discharge + drainage; declared pump flows, no ceiling)45,8 [31,1–59,0] min
  • Batch cycle time with the installed impeller (declared pump flows, no ceiling)45,9 [31,2–59,1] min
  • Blended volume per hour with the large impeller (declared pump flows: a scenario value, no ceiling)13,1 [10,2–19,3] m³/h
  • TypischBlended volume per hour with the installed impeller13,1 [10,1–19,3] m³/h
  • TheoretischThermodynamic minimum work of blending (ideal mixing is spontaneous)0 kJ/kg
  • Blending energy to specification with the large impeller (declared geometry, not a documented BAT)0,00905 [0,00587–0,01690] kJ/kg
  • TypischBlending energy to specification with the installed impeller0,0104 [0,0068–0,0199] kJ/kg
  • Initial coefficient of variation of the composition (segregated components)2,23 [1,75–2,94]
  • Residual coefficient of variation at the end of the blend0,00333 [0,00180–0,00655]
  • TheoretischMaximum OEE quality factor (share of batches within the composition specification)0,984 [0,869–0,997]
  • Mean thickness of the wall film after drainage (Jeffreys)22,6 [15,1–42,1] micrometer
  • Liquid left on the wetted walls after drainage0,483 [0,324–0,901] L
  • TheoretischMaximum yield (wall film after drainage only)0,999952 [0,999910–0,999968]
  • TypischYield with heel and line hold-up (declared scenario)0,9970 [0,9941–0,9988]
  • TheoretischMaximum availability (daily minimum cleaning)0,9844 [0,9791–0,9886]
  • Availability with declared changeovers (minimum cleaning between incompatible products)0,942 [0,876–0,974]
  • TypischAvailability with typical cleanings between incompatible products0,859 [0,701–0,931]
  • TheoretischPerformance factor against the physics-limited cycle1,00
  • TheoretischPhysics-bounded OEE0,968 [0,855–0,983]
  • OEE with declared changeovers0,927 [0,811–0,966]

3Obergrenzen je Dimension

Jede Dimension zeigt die vom Modell berechneten Obergrenzen und, bei vergleichbaren Einheiten, dokumentierte Vergleichswerte. Farbe und Markerform kennzeichnen den Grenztyp im gesamten Orakel.
  • Theoretisch
  • Beste verfügbare Technik
  • Best dokumentiert
  • Typisch
Zyklus- oder Verweilzeits · niedriger ist besser
  • TheoretischMinimum blend time to the specification homogeneity (large impeller)47,0 [31,9–57,3] s
  • TypischBlend time to the specification homogeneity (installed impeller)54,0 [36,2–67,2] s
Durchsatzm³/h · höher ist besser
  • TypischBlended volume per hour with the installed impeller13,1 [10,1–19,3] m³/h
Energie je ProdukteinheitkJ/kg · niedriger ist besser
  • TheoretischThermodynamic minimum work of blending (ideal mixing is spontaneous)0 kJ/kg
  • TheoretischDOE bandwidth study: products without significant chemical reactions have a zero thermodynamic minimum energy intensity · Vergleichswert0 kJ/kg
  • TypischBlending energy to specification with the installed impeller0,0104 [0,0068–0,0199] kJ/kg
Qualitäthöher ist besser
  • TheoretischMaximum OEE quality factor (share of batches within the composition specification)0,984 [0,869–0,997]
Ausbeutehöher ist besser
  • TheoretischMaximum yield (wall film after drainage only)0,999952 [0,999910–0,999968]
  • TypischYield with heel and line hold-up (declared scenario)0,9970 [0,9941–0,9988]
Verfügbarkeithöher ist besser
  • TheoretischMaximum availability (daily minimum cleaning)0,9844 [0,9791–0,9886]
  • TypischAvailability with typical cleanings between incompatible products0,859 [0,701–0,931]
Leistunghöher ist besser
  • TheoretischPerformance factor against the physics-limited cycle1,00
OEEhöher ist besser
  • TheoretischPhysics-bounded OEE0,968 [0,855–0,983]

4Verlustkaskade

Was jede Obergrenze von der nächsten trennt, von der physikalischen Grenze bis zum typischen Betrieb.
  1. TheoretischTypischZyklus- oder Verweilzeit
    47,0 [31,9–57,3] s → 54,0 [36,2–67,2] s (Abstand 6,99 s)

    The time ceilings are blend times to the specification homogeneity; the batch cycle, dominated by the declared fill and discharge pump flows, carries no ceiling. At equal power per volume the blend time scales as (T/D)^(1/3) and does not depend on the impeller type, so a small impeller costs time even though it turns faster. Real blends add what the correlation excludes: density and viscosity differences between concentrate and diluent (a heavy syrup sinks and must be lifted by the flow, which can lengthen the blend several times), dosing while the impeller is uncovered, dead zones under the impeller, and the time of sampling and laboratory release.

  2. TheoretischTypischEnergie je Produkteinheit
    0 kJ/kg → 0,0104 [0,0068–0,0199] kJ/kg (Abstand 0,0104 kJ/kg)

    Mixing ideal liquids is spontaneous: the Gibbs energy of mixing is negative, so no work is thermodynamically required. Work is needed only to make it fast: the agitator dissipates its whole power as heat by viscous friction. Blending energy is the power times the blend time; at equal power per volume a larger impeller reaches the same homogeneity sooner and therefore spends less energy. The installed impeller needs (T/D)^(1/3) more time at the same power, hence more energy. In practice the agitator often runs during the whole fill and discharge, not only for the blend time, and motor and gearbox losses are added; both multiply the energy without improving the blend.

  3. TheoretischTypischAusbeute
    0,999952 [0,999910–0,999968] → 0,9970 [0,9941–0,9988] (Abstand 0,00300)

    Physics leaves only the liquid film that clings to the wetted walls after gravity drainage, a few tens of micrometres thick and a fraction of a litre for a 10 m3 tank. The heel left below the outlet, the liquid in the pump, valves and pipes, and the first rinse that pushes the product out are technology: their volume depends on the tank bottom, the outlet position and the line layout, and dominates the loss. Pigging or air push-out of lines and sloped or dished bottoms close this gap.

5Physikalisch begrenzte OEE

Die höchste OEE, die die Operation erreichen kann: Verfügbarkeit, Leistung und Qualität, begrenzt nur durch unvermeidbare Stillstände und physikalische Prozessfähigkeit.
Anteil der Belegungszeit, der nach jedem unvermeidbaren Verlust verbleibt. Die Achse beginnt bei 0,80.
  • Belegungszeit (ideal)
    1,000
  • Verfügbarkeit
    Faktor 0,9844 [0,9791–0,9886]
    0,984 (−0,016)
  • Leistung
    Faktor 1,00
    0,984 (−0,000)
  • Qualität
    Faktor 0,984 [0,869–0,997]
    0,968 (−0,016)
  • Physikalisch begrenzte OEE
    0,968 [0,855–0,983]

6Vollständige Herleitung

Massen- und Energiebilanzen, geschwindigkeitsbestimmender Schritt, Prozessfähigkeit und unvermeidbare Stillstände, mit Erläuterung jedes Terms.

Scope. A beverage or dairy formulation is blended in a 10 m³ baffled, flat-bottomed cylindrical tank with liquid height equal to the tank diameter (H=TH = T) and one axial-flow impeller. A concentrate (syrup, flavour base) is dosed into water or milk and blended until the composition is uniform within specification; the batch is pumped out, the tank drains by gravity and the next batch is filled. Symbols and their values, units, uncertainty distributions and sources are listed in the parameter table generated from config/physics/mixing.yaml. Numbers quoted here are point values; the output table gives the Monte Carlo intervals.

1. Mass balance — maximum yield

Blending neither creates nor destroys mass: everything dosed into the tank leaves it as product, except what stays behind when the tank is emptied. The physics of emptying sets a lower bound on that residue: a viscous liquid draining down a vertical wall leaves a film whose thickness decreases with time but never vanishes.

Wall film after drainage (Jeffreys). For a Newtonian liquid of viscosity μ\mu and density ρ\rho draining under gravity gg from a vertical wall, the lubrication balance between weight and viscous shear gives a local film thickness, a time tt after the start of drainage and a distance xx below the top of the wetted wall,

h(x,t)=μ xρ g t.h(x,t) = \sqrt{\frac{\mu\,x}{\rho\,g\,t}} .

Averaging over the wetted height HH:

hˉ=1H∫0Hh dx=23μ Hρ g td=23 μm,\bar h = \frac{1}{H}\int_0^H h\,dx = \frac{2}{3}\sqrt{\frac{\mu\,H}{\rho\,g\,t_d}} = 23\ \mu\text{m},

for a drainage time tdt_d = 300 s and μ\mu = 1.5 mPa s. The wetted area is the wall plus the bottom, Aw=πTH+πT2/4A_w = \pi T H + \pi T^2/4 = 21 m²; the bottom is given the same mean thickness (a declared simplification). The hold-up and the theoretical yield are

Vfilm=hˉ Aw=0.48 L,Ymax=1−VfilmV=0.99995.V_{film} = \bar h\,A_w = 0.48\ \text{L}, \qquad Y_{max} = 1 - \frac{V_{film}}{V} = 0.99995 .

Technology. The heel below the outlet and the liquid in pump, valves and pipes (VhV_h, scenario 30 L) are properties of the installation, not of physics: Ytyp=1−(Vfilm+Vh)/V=0.9970Y_{typ} = 1 - (V_{film} + V_h)/V = 0.9970. The BAT reference document records that product is lost because equipment is difficult to empty before cleaning or a batch change, and reports a normal product loss of 0.5–1.5% for whole dairy plants; that boundary is wider than one tank and is not compared numerically.

2. Energy balance — minimum energy per unit of product

Thermodynamic minimum. For an ideal solution the Gibbs energy of mixing is

ΔGmix=R T∑iniln⁡xi<0,\Delta G_{mix} = R\,T \sum_i n_i \ln x_i < 0,

where nin_i and xix_i are the amount and mole fraction of each component and RR the molar gas constant. Every ln⁡xi\ln x_i is negative, so ΔGmix\Delta G_{mix} is negative for any composition: mixing is spontaneous and could, in principle, deliver work rather than consume it. The thermodynamic minimum work of blending is therefore zero (taking no credit for the recoverable work). Heats of mixing of aqueous sugar solutions are small and are neglected. This agrees with the DOE bandwidth study, which gives a zero thermodynamic minimum to products without significant chemical reactions.

Why energy is spent anyway. Molecular diffusion alone would take far longer than any production schedule: with a diffusion coefficient of order 10−910^{-9} m²/s, the diffusion time L2/DL^2/D over a metre is of the order of decades. The agitator buys speed: its shaft power PP is entirely dissipated as heat by viscous friction while it stretches and folds the fluid until diffusion can finish the job at small scales. The blending energy per kilogram is

e=P tblendρV,e = \frac{P\,t_{blend}}{\rho V},

0.0090 kJ/kg with the large impeller and 0.0104 kJ/kg with the installed impeller at 200 W/m³ (Section 3). The installed value is the typical energy ceiling and the theoretical one is zero; the large-impeller value uses a declared geometry, not a documented best available technique, so it is reported without a ceiling label.

3. Rate-limiting step — blend time and minimum batch cycle

Blend-time correlation. In the turbulent regime the time to reach 95% homogeneity, θ95\theta_{95}, of a baffled tank with H=TH = T is correlated by Grenville's equation (as presented by Grenville and Nienow, 2003, and Nienow, 1997):

N θ95=C Np−1/3(TD)2,C=5.20,N\,\theta_{95} = C\,N_p^{-1/3}\left(\frac{T}{D}\right)^2, \qquad C = 5.20,

where NN is the impeller speed, DD the impeller diameter, TT the tank diameter and NpN_p the turbulent power number of the impeller, which links power and speed through

P=Np ρ N3D5.P = N_p\,\rho\,N^3 D^5 .

Blend time at given power. Eliminating NN between the two equations:

N=(PNp ρ D5)1/3  ⇒  θ95=C T2D−1/3(ρP)1/3.N = \left(\frac{P}{N_p\,\rho\,D^5}\right)^{1/3} \;\Rightarrow\; \theta_{95} = C\,T^2 D^{-1/3}\left(\frac{\rho}{P}\right)^{1/3}.

The power number cancels: at equal power input the blend time does not depend on the impeller type, only on the geometry and the power. Because T3∝VT^3 \propto V, this is equivalent to θ95∝(P/V)−1/3 (T/D)1/3 T2/3\theta_{95} \propto (P/V)^{-1/3}\,(T/D)^{1/3}\,T^{2/3}: four times the power shortens the blend by 41/3=1.594^{1/3} = 1.59; a larger impeller at the same power blends faster. With VV = 10 m³ (TT = 2.34 m) and P/VP/V = 200 W/m³, θ95\theta_{95} = 24.9 s with D/TD/T = 0.33 and 21.7 s with D/TD/T = 0.50. The impeller speed (106 min⁻¹), Reynolds number Re=ρND2/μ=7×105Re = \rho N D^2/\mu = 7\times10^5 and tip speed (4.3 m/s) are reported to check that the flow is fully turbulent, as the correlation requires.

From 95% to the specification. Treat the decay of non-uniformity as first order: the normalised deviation from the final composition decays as e−kte^{-kt}. Since it falls from 1 to 0.05 at θ95\theta_{95}, k=ln⁡20/θ95k = \ln 20/\theta_{95}. The coefficient of variation (CoV) of composition across the tank starts, for a concentrate of volume fraction φ\varphi still segregated from the diluent, at

CoV0=1−φφ=2.23(φ=1/6),CoV_0 = \sqrt{\frac{1-\varphi}{\varphi}} = 2.23 \quad (\varphi = 1/6),

and CoV(t)=CoV0 e−ktCoV(t) = CoV_0\,e^{-kt}. The blend is stopped when the residual CoV is the composition tolerance δ\delta divided by a factor zhz_h (scenario 3), so that non-uniformity contributes little to the batch error:

tblend=θ95 ln⁡(CoV0 zh/δ)ln⁡20=2.17 θ95=47 s (large impeller), 54 s (installed).t_{blend} = \theta_{95}\,\frac{\ln(CoV_0\,z_h/\delta)}{\ln 20} = 2.17\,\theta_{95} = 47\ \text{s (large impeller)},\ 54\ \text{s (installed)}.

Minimum batch cycle. Filling and discharge are limited by the pumps (V˙f\dot V_f, V˙d\dot V_d) and the tank must drain for tdt_d before the next batch:

tcycle=VV˙f+tblend+VV˙d+td=45.8 min,V˙max=Vtcycle=13.1 m3/h.t_{cycle} = \frac{V}{\dot V_f} + t_{blend} + \frac{V}{\dot V_d} + t_d = 45.8\ \text{min}, \qquad \dot V_{max} = \frac{V}{t_{cycle}} = 13.1\ \text{m}^3/\text{h}.

With 20-minute fills and discharges the blend is a small share of the cycle; the pumps, not the agitator, are the main rate lever. Because the cycle and the rate are set by the declared pump flows, they are scenario values passed through a formula and carry no ceiling label; the physics ceiling of the time dimension is the blend time to specification. Under the common batch convention, fill, discharge and drainage belong to the ideal cycle, so they act through the performance factor (here 1, because the capable process needs no longer cycle) and not through availability. Drainage time trades cycle time against yield: the film thickness falls only as td−1/2t_d^{-1/2}.

4. Process capability — quality ceiling

The composition of a finished batch deviates from target for two independent reasons: the residual non-uniformity at the end of the blend (CoV=δ/zhCoV = \delta/z_h) and the error of the dosed quantities (relative standard deviation σd\sigma_d, load cells or flow meters), which no amount of mixing can remove. With both normally distributed, the relative composition error has standard deviation

σtot=σd2+(δ/zh)2,\sigma_{tot} = \sqrt{\sigma_d^2 + (\delta/z_h)^2},

and the share of batches within the tolerance ±δ\pm\delta is

Qmax=2 Φ ⁣(δσtot)−1=0.984,Q_{max} = 2\,\Phi\!\left(\frac{\delta}{\sigma_{tot}}\right) - 1 = 0.984,

with Φ\Phi the standard normal distribution function. A batch outside tolerance is corrected rather than destroyed, but it is not right first time and counts as a quality loss. Blending longer cannot raise QmaxQ_{max} above 2Φ(δ/σd)−12\Phi(\delta/\sigma_d) - 1: beyond a few θ95\theta_{95} the ceiling is set by dosing accuracy.

5. Unavoidable stops — maximum availability

Milk equipment must be cleaned at least once each day used. The minimum duration of the cleaning, tCIPt_{CIP}, is taken through a parameter link from the cleaning model (output cip_time_min: the physical minimum of the kinetic and displacement phases plus declared hold times). That model is valid for recirculated pipe circuits; the spray cleaning of the tank interior is outside its validity, so the linked duration is a lower bound:

Amax=1−tCIPtcyc=0.984.A_{max} = 1 - \frac{t_{CIP}}{t_{cyc}} = 0.984 .

Residues of one product (allergens, colours, flavours) may not be carried into an incompatible one, so the tank is also cleaned after each campaign of nbn_b compatible batches. That is a decision of the product mix, not physics: with the minimum duration it gives Ascen=nbtcycle/(nbtcycle+tCIP)A_{scen} = n_b t_{cycle}/(n_b t_{cycle} + t_{CIP}) = 0.942, and with the declared typical duration (1 h) the typical availability AtypA_{typ} = 0.859.

6. Physics-bounded OEE

Scope of the bound. The theoretical label of OEEmaxOEE_{max} means physics-bounded under the declared scenario: the ceiling follows from the physics of the operation for the declared product, equipment and schedule, and it is a bound only conditional on those declarations. It follows the common definition of all models: AmaxA_{max} counts only stops required by regulation or forced by a physical mechanism, at their physical minimum duration, plus the start-up they force; PmaxP_{max} is the ratio of the physics-limited ideal cycle to the cycle of the capable process; QmaxQ_{max} is the share of conforming units, and mass losses of conforming product are reported only as yield.

OEEmax=Amax×Pmax×Qmax,Pmax=1.OEE_{max} = A_{max} \times P_{max} \times Q_{max}, \qquad P_{max} = 1 .

Pmax=1P_{max} = 1 refers to the physics-limited cycle of Section 3. The result is OEEmaxOEE_{max} = 0.968, set mainly by dosing accuracy; with the declared cleanings between incompatible products, oee_scenario = 0.927.

7. Assumptions and validity

See the assumption and validity lists generated from the configuration file. The correlation applies to liquids of similar density and viscosity; a heavy syrup that sinks to the bottom needs a buoyancy correction not included here, and its real blend time can be several times longer. The most influential inputs (sensitivity table) are the cleaning duration and the campaign length for OEE, the dosing accuracy and the tolerance for quality, and the pump flows for the cycle time.

References

  • Grenville, R. K., Nienow, A. W. (2003). Blending of miscible liquids. In Handbook of Industrial Mixing, Wiley, 507–542. doi:10.1002/0471451452.ch9
  • Nienow, A. W. (1997). On impeller circulation and mixing effectiveness in the turbulent flow regime. Chemical Engineering Science, 52, 2557–2565. doi:10.1016/S0009-2509(97)00072-9
  • Jeffreys, H. (1930). The draining of a vertical plate. Mathematical Proceedings of the Cambridge Philosophical Society, 26, 204–205. doi:10.1017/s0305004100015437
  • European Commission, Joint Research Centre. Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries, 2019.
  • U.S. Department of Energy. Bandwidth Study on Energy Use and Potential Energy Saving Opportunities in U.S. Food and Beverage Manufacturing, 2017.
  • Bell, I. H., Wronski, J., Quoilin, S., Lemort, V. (2014). Pure and pseudo-pure fluid thermophysical property evaluation and the open-source thermophysical property library CoolProp. Industrial & Engineering Chemistry Research, 53, 2498–2508. doi:10.1021/ie4033999

7Parameter und Herkunft

Jede Eingangsgröße mit Wert, Einheit, Rolle, Unsicherheitsverteilung und Herkunft. Öffnen Sie ein Zitat, um die Quellenpassage zu lesen, die den Wert belegt.
  • VV10 m³

    Batch volume

    Szenario · Fest

    Deklarierte Annahme
  • ρ\rho1.040 kg/m³

    Density of the blended product

    Szenario · Gleichverteilt 1.000 bis 1.060 kg/m³

    Deklarierte Annahme
  • μ\mu0,0015 Pa·s

    Dynamic viscosity of the blended product (water at 20 °C from IAPWS through CoolProp, 1.0 mPa s, up to three times that value)

    Szenario · Gleichverteilt 0,001 bis 0,003 Pa·s

    Deklarierte Annahme

    CoolProp PropsSI('V','T',293.15,'P',101325,'Water') = 1.0e-3 Pa s; the multiplier for dissolved solids is a declared assumption.

  • P/VP/V200 W/m³

    Installed agitator power per unit volume

    Szenario · Gleichverteilt 100 bis 500 W/m³

    Deklarierte Annahme

    Design choice; declared assumption.

  • NpN_p1,3

    Turbulent power number of the installed impeller (four-blade 45° pitched-blade turbine)

    Szenario · Gleichverteilt 1,1 bis 1,7

    Deklarierte Annahme

    No open source with a quotable power number was used; declared assumption. At fixed power per volume the blend time does not depend on it; it only sets speed, Reynolds number and tip speed.

  • CC5,2

    Constant of the turbulent blend-time correlation N theta95 = C Np^(-1/3) (T/D)^2 for H = T

    Stoffwert · Fest

    Nur Referenz

    Literature constant (closed-access source, cited as reference only): Grenville correlation as presented by Grenville and Nienow (2003), doi:10.1002/0471451452.ch9, and Nienow (1997), doi:10.1016/S0009-2509(97)00072-9; derivation in physics_docs/mixing.en.md, section 3.

  • (D/T)inst(D/T)_{inst}0,33

    Impeller-to-tank diameter ratio installed

    Szenario · Gleichverteilt 0,25 bis 0,4

    Deklarierte Annahme
  • (D/T)L(D/T)_{L}0,5

    Largest impeller-to-tank diameter ratio considered for the best geometry

    Szenario · Fest

    Deklarierte Annahme

    Declared design limit of the comparison; larger impellers reduce blend time and energy at equal power per volume.

  • φ\varphi0,167

    Volume fraction of the dosed concentrate in the batch

    Szenario · Gleichverteilt 0,1 bis 0,25

    Deklarierte Annahme
  • δ\delta0,01

    Composition tolerance of the specification, relative to target (e.g. dissolved solids)

    Szenario · Gleichverteilt 0,005 bis 0,02

    Deklarierte Annahme
  • zhz_h3

    Ratio between tolerance and residual non-uniformity at which the blend is stopped

    Szenario · Fest

    Deklarierte Annahme

    Operating choice.

  • σd\sigma_d0,0025

    Relative standard deviation of the dosed quantities (load cells or flow meters)

    Szenario · Gleichverteilt 0,001 bis 0,004

    Deklarierte Annahme
  • V˙f\dot V_f30 m³/h

    Flow rate of the filling pumps

    Szenario · Gleichverteilt 20 bis 50 m³/h

    Deklarierte Annahme
  • V˙d\dot V_d30 m³/h

    Flow rate of the discharge pump

    Szenario · Gleichverteilt 20 bis 50 m³/h

    Deklarierte Annahme
  • tdt_d300 s

    Gravity drainage time after the pump loses suction

    Szenario · Gleichverteilt 120 bis 600 s

    Deklarierte Annahme
  • VhV_h30 L

    Heel and line hold-up left in tank bottom, outlet, pump and pipes

    Szenario · Gleichverteilt 10 bis 60 L

    Deklarierte Annahme
  • nbn_b8

    Batches of compatible products between two cleanings

    Szenario · Gleichverteilt 4 bis 16

    Deklarierte Annahme
  • tCIP,typt_{CIP,typ}1 h

    Duration of a typical cleaning-in-place of the tank between incompatible products

    Szenario · Gleichverteilt 0,75 bis 1,5 h

    Deklarierte Annahme

    Declared typical programme, used for the typical availability.

  • tCIPt_{CIP}0,374294 h

    Minimum duration of the cleaning-in-place: physical minimum of the kinetic and displacement phases plus declared hold times (output cip_time_min of the cleaning model)

    Stoffwert · Dreiecksverteilt 0,242184, 0,374294, 0,536161 h

    Berechnet

    Output `cip_time_min` of the cleaning model: 22.46 min [14.53, 32.17].

  • tcyct_{cyc}24 h

    Maximum interval between two cleanings of milk equipment (dairy formulations)

    Regulatorisch · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    all equipment is thoroughly cleaned at least once each day usedGrade "A" Pasteurized Milk Ordinance, 2023 Revision (öffnet in neuem Tab). U.S. Department of Health and Human Services, Public Health Service, Food and Drug Administration, 2023. S. 98. PMO 2023 Revision

8Vergleichswerte

Dokumentierte Werte aus offenen Quellen zur Prüfung der Obergrenzen; kein dokumentierter Wert darf die theoretische Grenze übertreffen.
VergleichswertObergrenzeWertHerkunft
DOE bandwidth study: products without significant chemical reactions have a zero thermodynamic minimum energy intensity
Wörtliches Zitat anzeigen
Most food and beverage products have a zero TM energy intensity because there are no significant chemical reactions involved.Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (öffnet in neuem Tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. S. 41. DOE/EE-1571; OSTI ID 1512366
Theoretisch0 kJ/kgVerifiziertes Zitat
Normal product loss in milk manufacture, percent of product (whole dairy, cleaning, start-up and changeover run-off included; wider boundary than one tank)
Wörtliches Zitat anzeigen
Product loss during milk manufacture can be as high as 3–4 %, with normally 0.5–1.5 % of the product being wasted.Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 395. EUR 29978 EN; JRC118627; doi:10.2760/243911
Typisch0,5 %Verifiziertes Zitat

9Unvermeidbare Stillstände

Stillstände, die Physik oder Regulierung erzwingen; sie bestimmen die maximale Verfügbarkeit.
  • Cleaning at least once per day of use (milk equipment)Verifiziertes Zitat

    Hygiene regulation for milk equipment; minimum duration from the cleaning model.

    Wörtliches Zitat anzeigen
    all equipment is thoroughly cleaned at least once each day usedGrade "A" Pasteurized Milk Ordinance, 2023 Revision (öffnet in neuem Tab). U.S. Department of Health and Human Services, Public Health Service, Food and Drug Administration, 2023. S. 98. PMO 2023 Revision
  • Cleaning between incompatible products (scenario stop: availability_scenario and typical availability only)Verifiziertes Zitat

    Residues of one product (allergens, colours, flavours) cannot be carried into an incompatible one; the BAT reference document records the product lost because equipment is difficult to empty before cleaning or a batch change. Interval and duration are declared scenario values.

    Wörtliches Zitat anzeigen
    Product loss to waste water caused by difficulties of emptying the equipment before cleaning/shift of production batch.Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 536. EUR 29978 EN; JRC118627; doi:10.2760/243911

10Annahmen

  1. Availability: the only physically or legally required stop is the daily cleaning of milk equipment, at the minimum duration of the cleaning model. That model is valid for recirculated pipe circuits; the spray cleaning of the tank interior is outside its validity, so the linked duration is a lower bound. Cleanings between incompatible products are a product-mix decision: they enter availability_scenario (at the minimum duration) and the typical availability (at the declared typical duration). Fill, discharge and drainage belong to the ideal batch cycle (common batch convention), so they do not reduce availability.
  2. Fully turbulent flow in a baffled vessel with H = T and a single impeller; the blend-time correlation applies to liquids of similar density and viscosity.
  3. Non-uniformity decays exponentially (first order) with a rate constant fixed by the 95 % blend time: k = ln 20 / theta95; the coefficient of variation follows the same decay from its segregated initial value.
  4. The blend is stopped when the residual coefficient of variation is the tolerance divided by z_h; dosing errors are independent and normally distributed; a batch outside tolerance is counted as a quality loss (it is corrected, not destroyed).
  5. Wall film after drainage follows Jeffreys' solution for a Newtonian liquid on a vertical plate; the bottom is assigned the same mean film thickness.
  6. Mixing is treated as ideal (no heat of mixing, no reaction); the thermodynamic minimum work is zero.

11Gültigkeitsbereich

  • Low-viscosity miscible liquids (up to a few mPa s) in baffled tanks with one axial or radial impeller, impeller Reynolds number above 10 000.
  • Concentrates whose density differs strongly from the diluent need a correction for buoyancy that is not included.

12Sensitivität

Elastizität: relative Änderung der Ergebnisgröße bei relativer Änderung jedes Parameters. Daneben steht die Spearman-Rangkorrelation aus den Monte-Carlo-Ziehungen.
  • zhz_hRatio between tolerance and residual non-uniformity at which the blend is stopped
    Elastizität +0,071Spearman-ρ —
  • δ\deltaComposition tolerance of the specification, relative to target (e.g. dissolved solids)
    Elastizität +0,040Spearman-ρ +0,66
  • σd\sigma_dRelative standard deviation of the dosed quantities (load cells or flow meters)
    Elastizität -0,039Spearman-ρ -0,63
  • tcyct_{cyc}Maximum interval between two cleanings of milk equipment (dairy formulations)
    Elastizität +0,016Spearman-ρ —
  • tCIPt_{CIP}Minimum duration of the cleaning-in-place: physical minimum of the kinetic and displacement phases plus declared hold times (output cip_time_min of the cleaning model)
    Elastizität -0,016Spearman-ρ -0,27
  • Größe steigt mit dem Parameter
  • Größe sinkt mit dem Parameter

13Validierungsprüfungen

Ein Modell wird nur veröffentlicht, wenn alle Prüfungen bestanden sind.
  • Dimensionsanalyse28 outputs converted to their declared unitsBestanden
  • Jeder zitierte Wert an seiner Quelle verifiziert5 verified, 0 failedBestanden
  • Kein dokumentierter Wert übertrifft die theoretische GrenzeBestanden
  • Obergrenzen in physikalischer ReihenfolgeBestanden
  • Anteile zwischen 0 und 1Bestanden

14Verlustursachen in dieser Operation

Wahrscheinlichkeit, dass jede Ursache als relevanter Verlust einer Linie dokumentiert ist, gepoolt über alle Segmente.

15Literatur

  1. Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 395. EUR 29978 EN; JRC118627; doi:10.2760/243911
  2. Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (öffnet in neuem Tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. S. 41. DOE/EE-1571; OSTI ID 1512366
  3. doi:10.1002/0471451452.ch9 — Blending of miscible liquids (turbulent blend-time correlation).
  4. doi:10.1016/S0009-2509(97)00072-9 — Impeller circulation and mixing effectiveness in turbulent flow.
  5. doi:10.1017/s0305004100015437 — Drainage of a liquid film on a vertical plate.
  6. doi:10.1021/ie4033999 — Thermophysical property library (CoolProp).