foratvise
Loslegen
Abfüll- und Verpackungslinie

Verschließen und Falzen

Double seaming of three-piece food cans on a rotary seamer

Validiertes ModellOEE-Grenze 0,999 [0,864–1,000]20.000 Monte-Carlo-Stichproben · Seed 20261115 · berechnet am 16. November 2026

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Verschließen und Falzen kann höchstens 100 von je 100 geplanten Stunden nutzen. Der Rest entfällt auf Grenzen, die kein Werk vermeiden kann.

  1. 100höchstens nutzbar

Die drei Grenzen, die das festlegen

Laufzeit: bis 100 %

Der Rest sind Stillstände, die Physik oder Vorschrift erzwingen: Reinigung, Umrüsten, Abtauen.

Geschwindigkeit: bis 100 %

Wie nah an ihrer Höchstgeschwindigkeit sie laufen kann, ohne Produkt oder Anlage zu schädigen.

Gutprodukt: bis 100 %

Ein Teil des Produkts liegt auch bei gut beherrschtem Prozess außerhalb der Spezifikation.

Das technische Detail ansehen

Technisches Detail

Unsicherheitsintervalle, physikalische Modelle je Station und Quellen, für alle, die jede Zahl prüfen möchten.

1Szenario

Canned vegetables are closed in round three-piece steel cans of the 300-303 diameter group (a No. 303 can, 3 3/16 in). After filling, a can end is placed on each can and a rotary seamer with several seaming heads rolls the end curl and the body flange into a double seam in two operations (first-operation roll, second-operation roll) while the can is held by its chuck. The seamer is synchronised with the filler. The double seam is the hermetic closure of a low-acid food that is sterilised afterwards, so its integrity is regulated (21 CFR 113.60). Of the two closures of the processes that use this unit operation (screw caps on PET bottles of carbonated soft drinks, double seams on cans), the double seam is the one whose acceptance criteria and inspection duties are stated in openly readable regulations and guidance, so it is the scenario modelled here.

Herkunft der EingangsgrößenDeklarierte Annahme22Verifiziertes Zitat10

2Ergebnisse

Punktwert aus den Nominalparametern und 95-%-Intervall aus 20.000 Monte-Carlo-Ziehungen der unsicheren Parameter.
  • Body hook length aimed at (centre of the set-up aim)0,0825 inch
  • Cover (end) hook length aimed at (operating minimum plus the capability margin)0,0753 [0,0735–0,0792] inch
  • Internal seam length C = W - k (2 T_e + t_b) at the nominal seam length0,0881 [0,0822–0,0939] inch
  • Overlap at the nominal hook and seam lengths, BH + CH + T_e - W0,0513 [0,0461–0,0584] inch
  • Percent overlap at the nominal setting (overlap over internal seam length)58,2 [49,6–70,3] %
  • Body hook butting at the nominal setting84,3 [79,2–90,2] %
  • Standard deviation of the overlap (hook and seam-length dispersion)0,00312 [0,00276–0,00407] inch
  • Share of seams below the hold-for-investigation minimum overlap9,39 × 10⁻⁸ [1,49 × 10⁻¹²–5,09 × 10⁻⁴]
  • Share of seams below 45 % overlap4,37 × 10⁻⁴ [1,03 × 10⁻⁸–1,35 × 10⁻¹]
  • Share of seams below 70 % body hook butting2,65 × 10⁻⁷ [8,65 × 10⁻¹²–7,09 × 10⁻⁴]
  • TheoretischMaximum OEE quality factor: share of seams meeting all three criteria with a capable seaming station1,000 [0,865–1,000]
  • TypischQuality factor when the seam dimensions only just fill the operating limits (declared typical dispersion)0,986 [0,776–1,000]
  • Seaming time per can (roll revolutions over spindle speed; declared kinematics)0,300 [0,169–0,489] s
  • Cans per minute of the rotary seamer at the declared kinematics600 [348–1.111] 1/min
  • Plastic folding work per can end (rigid-perfectly-plastic lower bound)9,06 [5,97–16,94] J
  • TheoretischMinimum mechanical work of double seaming per kg of packed product (plastic folding)0,0201 [0,0133–0,0377] kJ/kg
  • Share of cans destroyed by the teardown examinations4,17 × 10⁻⁵ [2,92 × 10⁻⁵–1,19 × 10⁻⁴]
  • TheoretischMaximum yield of conforming cans (teardown samples destroyed)0,999958 [0,999881–0,999971]
  • TheoretischMaximum availability (seaming-roll and chuck replacement forced by wear)0,9995 [0,9976–0,9998]
  • Availability with declared can-size changeovers0,972 [0,918–0,991]
  • TheoretischPerformance factor: the seamer runs synchronised with the filler at its rated speed1,00
  • TheoretischPhysics-bounded OEE0,999 [0,864–1,000]
  • OEE with declared can-size changeovers0,971 [0,839–0,990]

3Obergrenzen je Dimension

Jede Dimension zeigt die vom Modell berechneten Obergrenzen und, bei vergleichbaren Einheiten, dokumentierte Vergleichswerte. Farbe und Markerform kennzeichnen den Grenztyp im gesamten Orakel.
  • Theoretisch
  • Beste verfügbare Technik
  • Best dokumentiert
  • Typisch
Qualitäthöher ist besser
  • TheoretischMaximum OEE quality factor: share of seams meeting all three criteria with a capable seaming station1,000 [0,865–1,000]
  • TypischQuality factor when the seam dimensions only just fill the operating limits (declared typical dispersion)0,986 [0,776–1,000]
Energie je ProdukteinheitkJ/kg · niedriger ist besser
  • TheoretischMinimum mechanical work of double seaming per kg of packed product (plastic folding)0,0201 [0,0133–0,0377] kJ/kg
Ausbeutehöher ist besser
  • TheoretischMaximum yield of conforming cans (teardown samples destroyed)0,999958 [0,999881–0,999971]
Verfügbarkeithöher ist besser
  • TheoretischMaximum availability (seaming-roll and chuck replacement forced by wear)0,9995 [0,9976–0,9998]
Leistunghöher ist besser
  • TheoretischPerformance factor: the seamer runs synchronised with the filler at its rated speed1,00
OEEhöher ist besser
  • TheoretischPhysics-bounded OEE0,999 [0,864–1,000]

4Verlustkaskade

Was jede Obergrenze von der nächsten trennt, von der physikalischen Grenze bis zum typischen Betrieb.
  1. TheoretischTypischQualität
    1,000 [0,865–1,000] → 0,986 [0,776–1,000] (Abstand 0,0132)

    The quality ceiling is the share of seams that meet three geometric criteria at once: an overlap of at least the hold-for-investigation minimum, an overlap of at least 45 % of the internal seam length and a body hook butting of at least 70 %. The overlap is the sum of the two hooks and the end plate minus the seam length, so its spread is the combined spread of the body hook, the cover hook and the seam length. A capable seaming station keeps its aim 3 to 4 standard deviations inside the operating limits of the hooks; when the dispersion grows until the hooks only just fill the operating limits, the low tail of the overlap crosses the 45 % line far more often. The causes of a wider dispersion are worn rolls and chucks (the seam lengthens), a base-plate pressure that drifts (the body hook changes length), flange width and end-curl variation of the incoming components, and roll settings that are not reset after a jam; this is why the regulation asks for visual checks every 30 minutes and teardowns every 4 hours.

5Physikalisch begrenzte OEE

Die höchste OEE, die die Operation erreichen kann: Verfügbarkeit, Leistung und Qualität, begrenzt nur durch unvermeidbare Stillstände und physikalische Prozessfähigkeit.
Anteil der Belegungszeit, der nach jedem unvermeidbaren Verlust verbleibt. Die Achse beginnt bei 0,80.
  • Belegungszeit (ideal)
    1,000
  • Verfügbarkeit
    Faktor 0,9995 [0,9976–0,9998]
    1,000 (−0,000)
  • Leistung
    Faktor 1,00
    1,000 (−0,000)
  • Qualität
    Faktor 1,000 [0,865–1,000]
    0,999 (−0,000)
  • Physikalisch begrenzte OEE
    0,999 [0,864–1,000]

6Vollständige Herleitung

Massen- und Energiebilanzen, geschwindigkeitsbestimmender Schritt, Prozessfähigkeit und unvermeidbare Stillstände, mit Erläuterung jedes Terms.

Scope. Canned vegetables are closed in round three-piece steel cans of the 300-303 diameter group (a No. 303 can, 3 3/16 in = 81 mm). A rotary seamer with NhN_h seaming heads places an end on each filled can and rolls the end curl and the body flange into a double seam in two operations while the can is held by its chuck; the seamer is synchronised with the filler. Of the two closures in the processes that use this unit operation (screw caps on PET bottles, double seams on cans), the double seam is the one whose acceptance criteria and inspection duties are stated in openly readable regulations and guidance (21 CFR 113.60, the CFIA metal-can manual, FAO guidance), so it is the scenario modelled. Symbols and their values, units, uncertainty distributions and sources are listed in the parameter table generated from config/physics/capping.yaml. Numbers quoted here are point values; the output table gives the Monte Carlo intervals.

1. Mass balance — maximum yield

Seaming adds an end to a can; it consumes no product. Product is lost only where conforming cans are destroyed: 21 CFR 113.60(a)(1) requires teardown examinations of the double seam "on enough containers from each seaming station", recorded at intervals that should not exceed 4 hours. A teardown destroys the can. With ntdn_{td} cans per station (at least one) every Δtd\Delta_{td} = 4 h at the machine rate n˙\dot n,

ftd=Nh ntdn˙ Δtd,Ymax=1−ftd=0.99996.f_{td} = \frac{N_h\,n_{td}}{\dot n\,\Delta_{td}}, \qquad Y_{max} = 1 - f_{td} = 0.99996 .

The visual seam checks every 30 minutes (one can per head) are made on cans that return to the line and cost nothing. Torn-down cans are conforming product, so this loss is a yield loss and does not enter the quality factor.

2. Energy balance — minimum work per can

The seam is formed by bending: the end curl is folded under the flange and both are pressed flat in the second operation. For a rigid-perfectly-plastic sheet of thickness tt and yield strength σy\sigma_y, the plastic moment per unit length of a fold line is

Mp=σy t24,M_p = \frac{\sigma_y\,t^2}{4},

and the plastic work of folding a length PP through an angle θ\theta is Mp θ PM_p\,\theta\,P. The end plate (TeT_e) is folded through a total angle θe\theta_e (about 2π2\pi: it is curled about half a turn and flattened back) and the body flange (tbt_b) through θb\theta_b (about π\pi), along the seam perimeter P=πDP = \pi D:

Wfold=(σyTe24 θe+σytb24 θb)πD=9.1 J per can,W_{fold} = \left(\frac{\sigma_y T_e^2}{4}\,\theta_e + \frac{\sigma_y t_b^2}{4}\,\theta_b\right)\pi D = 9.1\ \text{J per can},

or 0.020 kJ per kg of product for 0.45 kg per can. This is a lower bound of the mechanical work of a rate-independent plastic metal: friction of the rolls, strain hardening, elastic springback and the flow of the sealing compound come on top. No open source quotes a tinplate yield strength or the fold angles, so they are declared scenario values with ranges; the result scales linearly with σy\sigma_y and with the square of the plate thicknesses. It is negligible against the energy of the drives of a seamer and of the thermal processing that follows.

3. Rate-limiting step — seaming time and machine rate

Each head forms one seam while it travels the share ϕ\phi of a turret revolution (the rest is can infeed and discharge). The two seaming operations need together nrn_r revolutions of the rolls relative to the can at the spindle speed NsN_s, so

tseam=nrNs=0.30 s,n˙=Nh ϕtseam=600 cans/min.t_{seam} = \frac{n_r}{N_s} = 0.30\ \text{s}, \qquad \dot n = \frac{N_h\,\phi}{t_{seam}} = 600\ \text{cans/min}.

No open source states seaming kinematics, so nrn_r, NsN_s, ϕ\phi and NhN_h are declared; the time and rate are reported without a theoretical label (assumption a4). In the line, the seamer runs synchronised with the filler at its rated speed, and its performance factor is 1: no capability margin of the seam lengthens the cycle in this model.

4. Process capability — quality ceiling

Seam geometry. The double seam interlocks the body hook BHBH (formed from the body flange) and the cover hook CHCH (formed from the end curl) inside the seam length WW. Conservation of the folded lengths gives the overlap stated in 21 CFR 113.60 and in the FDA Bacteriological Analytical Manual:

OL=CH+BH+Te−W.OL = CH + BH + T_e - W .

The internal seam length, the space available for the hooks, is the seam length minus the three end-plate and two body-plate layers; the teardown formula of body hook butting in the CFIA manual applies a factor kk = 1.1 to the plate thicknesses:

C=W−k (2Te+tb).C = W - k\,(2T_e + t_b) .

Acceptance criteria. A seam is accepted when three geometric criteria hold at once:

  1. OL≥OLHFIOL \ge OL_{HFI} — the overlap is not below the hold-for-investigation minimum of the CFIA example guidelines for three-piece round sanitary cans (300-303 diameters, steel ends: 0.035 in; its operating limit is 0.040 in);
  2. OL/C≥pOLOL / C \ge p_{OL} = 45 % — good manufacturing practice cited by FAO: the overlap should be at least 45 % of the internal seam length;
  3. (BH−k tb)/C≥pBHB(BH - k\,t_b)/C \ge p_{BHB} = 70 % — the CFIA manual: "a minimum of 70% body hook butting is required to ensure an adequate seal".

Dimensions of a capable seaming station. The body hook is centred in its set-up aim (0.080–0.085 in for diameters 207.5–401, CFIA) and its dispersion is set by the operating limit ±ΔBH\pm\Delta_{BH} = ±0.008 in: a capable station keeps the aim zcapz_{cap} standard deviations inside it, σBH=ΔBH/zcap\sigma_{BH} = \Delta_{BH}/z_{cap}. The cover hook is aimed zcapz_{cap} standard deviations above its operating minimum, CH‾=CHmin+zcapσCH\overline{CH} = CH_{min} + z_{cap}\sigma_{CH} with CHminCH_{min} = 0.070 in. The seam length (set by the second-operation roll profile) and the plate thicknesses are declared, because the open guidance leaves them to the can maker. With zcapz_{cap} = 3.5, W‾\overline W = 0.115 in, TeT_e = 0.0085 in and tbt_b = 0.0075 in:

C=0.0881 in,OL=0.0513 in (1.30 mm),OL/C=58.2 %,BHB=84.3 %,σOL=σBH2+σCH2+σW2=0.0031 in.C = 0.0881\ \text{in}, \quad OL = 0.0513\ \text{in}\ (1.30\ \text{mm}), \quad OL/C = 58.2\,\%, \quad BHB = 84.3\,\%, \quad \sigma_{OL} = \sqrt{\sigma_{BH}^2+\sigma_{CH}^2+\sigma_W^2} = 0.0031\ \text{in}.

Conforming share. BHBH, CHCH and WW are independent normal variables. Each criterion is linear in them, so each marginal failure is a normal probability:

f1=Φ ⁣(OLHFI−OL‾σOL),f2=Φ ⁣(−OL‾−pOLC‾σBH2+σCH2+(1+pOL)2σW2),f3=Φ ⁣(−BH‾−ktb−pBHBC‾σBH2+pBHB2σW2),f_1 = \Phi\!\left(\frac{OL_{HFI} - \overline{OL}}{\sigma_{OL}}\right), \quad f_2 = \Phi\!\left(-\frac{\overline{OL} - p_{OL}\overline C}{\sqrt{\sigma_{BH}^2+\sigma_{CH}^2+(1+p_{OL})^2\sigma_W^2}}\right), \quad f_3 = \Phi\!\left(-\frac{\overline{BH} - k t_b - p_{BHB}\overline C}{\sqrt{\sigma_{BH}^2+p_{BHB}^2\sigma_W^2}}\right),

with Φ\Phi the standard normal distribution function: f1=9×10−8f_1 = 9\times10^{-8}, f2=4.4×10−4f_2 = 4.4\times10^{-4}, f3=2.6×10−7f_3 = 2.6\times10^{-7}. The three criteria are correlated (they share BHBH and WW), so the share of cans meeting all of them is integrated exactly: for a fixed seam length the butting criterion sets a lower limit of BHBH, and for fixed (W,BH)(W, BH) the two overlap criteria set a lower limit of CHCH whose probability is analytic,

Qmax=∫ϕW(w)∫BH≥pBHBC(w)+ktbϕBH(b)  Φ ⁣(CH‾−max⁡ ⁣(OLHFI, pOLC(w))+b+Te−wσCH)db dw=0.99956,Q_{max} = \int \phi_W(w) \int_{BH \ge p_{BHB}C(w) + k t_b} \phi_{BH}(b)\; \Phi\!\left(\frac{\overline{CH} - \max\!\big(OL_{HFI},\,p_{OL}C(w)\big) + b + T_e - w}{\sigma_{CH}}\right) db\, dw = 0.99956,

evaluated with Gauss–Hermite quadrature in WW and Gauss–Legendre quadrature in BHBH (checked against two million direct samples in the tests). The 45 % criterion binds: the seam length enters the overlap with weight 1+pOL1 + p_{OL}, so the seam length and its dispersion dominate the quality ceiling. When the hook dispersion only just fills the operating limits (ztypz_{typ} = 2 instead of 3.5) the conforming share falls to 0.986 (quality_typical).

Tightness (wrinkle rating), pressure ridge, juncture rating, cutovers, droops, false seams and compound defects are not modelled, so QmaxQ_{max} is an upper bound of the seam quality.

5. Unavoidable stops — maximum availability

No cleaning-in-place applies to a seamer, so the cleaning model is not used. The groove profile of the seaming rolls wears with every seam, and the CFIA manual notes that seam length "is partly dependent on the roll groove profile and the degree of seaming roll wear": as the rolls wear, the seam lengthens and the overlap shrinks (section 4), so worn rolls and chucks must be replaced and the seams set up again. This is a stop forced by a physical mechanism that accumulates during production. With a roll change of duration trt_r every Δr\Delta_r hours of running,

Amax=1−trΔr=0.9995.A_{max} = 1 - \frac{t_r}{\Delta_r} = 0.9995 .

Interval and duration are declared scenario values (no open source states them). Can-size changeovers are a product-mix decision and enter only

Ascen=Amax−tcoΔco=0.972.A_{scen} = A_{max} - \frac{t_{co}}{\Delta_{co}} = 0.972 .

The regulation adds visual checks every 30 minutes and after every jam, adjustment or start-up, and teardowns every 4 hours; they are made on cans taken from the running line and do not stop the seamer.

6. Physics-bounded OEE

Scope of the bound. The theoretical label of OEEmaxOEE_{max} means physics-bounded under the declared scenario: the ceiling follows from the physics and the regulatory acceptance criteria of the operation for the declared can, seamer and schedule, and it is a bound only conditional on those declarations. It follows the common definition of all models: AmaxA_{max} counts only stops required by regulation or forced by a physical mechanism, at their minimum duration; PmaxP_{max} is the ratio of the physics-limited ideal cycle to the cycle of the capable process; QmaxQ_{max} is the share of conforming units, and mass losses of conforming product (here the torn-down cans) are reported only as yield.

OEEmax=Amax×Pmax×Qmax=0.9995×1×0.99956=0.9991.OEE_{max} = A_{max} \times P_{max} \times Q_{max} = 0.9995 \times 1 \times 0.99956 = 0.9991 .

With the declared can-size changeovers, oee_scenario = 0.971. The Monte Carlo interval of OEEmaxOEE_{max} is wide on the low side because the seam length and the plate thicknesses are declared over ranges in which the 45 % overlap criterion becomes binding; the sensitivity table shows it.

Consistency with the filling model. The filling model bounds fill volume and give-away; this model starts with a filled can and counts neither fill nor head-space. Container sterility and the thermal process belong to the sterilization model; this model stops at the geometric integrity of the closure.

7. Assumptions and validity

See the assumption and validity lists generated from the configuration file. The most influential inputs (sensitivity table) are the nominal seam length and its dispersion, the plate thicknesses and the capability margin for quality, and the roll-change interval for availability.

Use for other processes. The codebook assigns capping_seaming to two processes. For canned vegetables the model applies directly. For carbonated soft drinks the closure is a screw cap applied to a PET bottle, a different mechanism for which no openly readable regulation with measurable conformity criteria was found; the ceiling of this model is used there as an approximation of the same form (a closure that either conforms or is rejected, and tooling that must be changed as it wears). It is not a bound derived for screw capping.

References

  • U.S. Code of Federal Regulations, Title 21, Part 113, Thermally processed low-acid foods packaged in hermetically sealed containers, § 113.60 Containers (4-1-25 edition).
  • Canadian Food Inspection Agency. Metal can defects: identification and classification manual (Table 4.1.5, example of double seam guidelines; source quoted there: Can Manufacturers Institute, voluntary industry can standards).
  • U.S. Food and Drug Administration. Bacteriological Analytical Manual, Chapter 22A, Examination of metal containers for integrity (overlap and percent-overlap formulas).
  • FAO. Planning and engineering data 2. Fish canning, Fisheries Circular 784, chapter 4 (overlap at least 45 % of the internal seam length).

7Parameter und Herkunft

Jede Eingangsgröße mit Wert, Einheit, Rolle, Unsicherheitsverteilung und Herkunft. Öffnen Sie ein Zitat, um die Quellenpassage zu lesen, die den Wert belegt.
  • BHaim,loBH_{aim,lo}80 thou

    Lower end of the set-up aim of the body hook length, round sanitary cans of 207.5 to 401 diameter

    Technik · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    Body hook length Table Note 1 | 207.5 - 401 | .080 - .085 | .080 ± .008Metal can defects: identification and classification manual (öffnet in neuem Tab). Canadian Food Inspection Agency, Government of Canada, 2020. CFIA, Preventive controls for food: metal can defects
  • BHaim,hiBH_{aim,hi}85 thou

    Upper end of the set-up aim of the body hook length

    Technik · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    Body hook length Table Note 1 | 207.5 - 401 | .080 - .085 | .080 ± .008Metal can defects: identification and classification manual (öffnet in neuem Tab). Canadian Food Inspection Agency, Government of Canada, 2020. CFIA, Preventive controls for food: metal can defects
  • ΔBH\Delta_{BH}8 thou

    Half-width of the operating limit of the body hook length (.080 ± .008 in)

    Technik · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    Body hook length Table Note 1 | 207.5 - 401 | .080 - .085 | .080 ± .008Metal can defects: identification and classification manual (öffnet in neuem Tab). Canadian Food Inspection Agency, Government of Canada, 2020. CFIA, Preventive controls for food: metal can defects
  • CHminCH_{min}70 thou

    Operating minimum of the cover (end) hook length, diameters 300 to 401

    Technik · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    End hook length Table Note 2 | 300 - 401 | | .070 Min.Metal can defects: identification and classification manual (öffnet in neuem Tab). Canadian Food Inspection Agency, Government of Canada, 2020. CFIA, Preventive controls for food: metal can defects
  • OLHFIOL_{HFI}35 thou

    Minimum optical overlap below which the cans are held for investigation (steel ends, diameters 300-303)

    Technik · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    Optical overlap | 300-303 | | 0040 Min. | .035 Min. | {not developed}Metal can defects: identification and classification manual (öffnet in neuem Tab). Canadian Food Inspection Agency, Government of Canada, 2020. CFIA, Preventive controls for food: metal can defects
  • pOLp_{OL}45 %

    Minimum overlap as a share of the internal seam length (good manufacturing practice)

    Regulatorisch · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    Good manufacturing practice indicates that the. overlap should be at least 45 % of the internal seam lenght to ensure that the seam will function correctly and resist to minor abuse.Planning and engineering data 2. Fish canning (FAO Fisheries Circular No. 784), chapter 4: Processing operations (öffnet in neuem Tab). Food and Agriculture Organization of the United Nations, 1988. FAO Fisheries Circular No. 784, FIIU/C784(En)
  • pBHBp_{BHB}70 %

    Minimum body hook butting (internal body hook length over internal seam length)

    Technik · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    Experience indicates that a minimum of 70% body hook butting is required to ensure an adequate seal.Metal can defects: identification and classification manual (öffnet in neuem Tab). Canadian Food Inspection Agency, Government of Canada, 2020. CFIA, Preventive controls for food: metal can defects
  • kk1,1

    Factor applied to the plate thicknesses in the internal seam length (teardown formula of body hook butting)

    Technik · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    % Body Hook Butting = (BH − 1.1tb ÷ SL − 1.1(2te + tb)) × 100Metal can defects: identification and classification manual (öffnet in neuem Tab). Canadian Food Inspection Agency, Government of Canada, 2020. CFIA, Preventive controls for food: metal can defects
  • zcapz_{cap}3,5

    Capability margin of a capable seaming station: number of standard deviations between the aim and the operating limits of the hooks

    Szenario · Gleichverteilt 3 bis 4

    Deklarierte Annahme

    Operating choice, point value at the centre of the declared range 3-4 (capability index 1.0-1.33 against the operating limits). Sets sigma_BH = tolerance / z and the end-hook aim = operating minimum + z sigma_CH.

  • ztypz_{typ}2

    Typical capability margin: the hook dimensions only just fill the operating limits

    Szenario · Gleichverteilt 1,5 bis 2,5

    Deklarierte Annahme

    Declared typical dispersion, used only for quality_typical.

  • σCH\sigma_{CH}1,5 thou

    Standard deviation of the cover hook length of a capable seaming station

    Szenario · Gleichverteilt 1 bis 2,5 thou

    Deklarierte Annahme

    No open source with measured seam-dimension dispersions was found; declared assumption.

  • Wˉ\bar W115 thou

    Nominal seam length (width, height) set by the second-operation roll profile

    Szenario · Gleichverteilt 110 bis 120 thou

    Deklarierte Annahme

    The open guidance read gives no seam-length guideline for this can size (the can maker supplies it); declared assumption. Overlap and the two percentages fall as the seam length grows.

  • σW\sigma_W1,5 thou

    Standard deviation of the seam length

    Szenario · Gleichverteilt 1 bis 2,5 thou

    Deklarierte Annahme
  • TeT_e8,5 thou

    Thickness of the end (cover) plate

    Szenario · Gleichverteilt 7,5 bis 9,5 thou

    Deklarierte Annahme

    Tinplate end of about 0.22 mm; declared assumption.

  • tbt_b7,5 thou

    Thickness of the body plate

    Szenario · Gleichverteilt 6,5 bis 8,5 thou

    Deklarierte Annahme

    Tinplate body of about 0.19 mm; declared assumption.

  • NhN_h6

    Number of seaming heads of the rotary seamer

    Szenario · Fest

    Deklarierte Annahme
  • ϕ\phi0,5

    Share of a turret revolution during which a head is seaming (the rest is can infeed and discharge)

    Szenario · Gleichverteilt 0,4 bis 0,6

    Deklarierte Annahme
  • nrn_r10

    Revolutions of the seaming rolls around the can for both operations together

    Szenario · Gleichverteilt 6 bis 14

    Deklarierte Annahme

    No open source with seaming kinematics was found; declared assumption.

  • NsN_s2.000 1/min

    Rotational speed of the seaming head (rolls relative to the can)

    Szenario · Gleichverteilt 1.500 bis 2.500 1/min

    Deklarierte Annahme
  • Δtd\Delta_{td}4 h

    Longest interval between teardown examinations of each seaming station

    Regulatorisch · Fest

    Verifiziertes Zitat
    Wörtliches Zitat anzeigen
    Such examinations and recordings should be made at intervals not to ex- ceed 4 hours.21 CFR Part 113 — Thermally Processed Low-Acid Foods Packaged in Hermetically Sealed Containers (4-1-25 Edition) (öffnet in neuem Tab). U.S. Government Publishing Office (Code of Federal Regulations), 2025. S. 29. 21 CFR 113 (2025)
  • ntdn_{td}1

    Cans destroyed per seaming station at each teardown examination

    Szenario · Gleichverteilt 1 bis 2

    Deklarierte Annahme

    21 CFR 113.60(a)(1) asks for 'enough containers from each seaming station' without a number; one can per station is the least.

  • Δr\Delta_{r}2.000 h

    Running time between two replacements of worn seaming rolls and chucks

    Szenario · Gleichverteilt 500 bis 4.000 h

    Deklarierte Annahme

    Wear-limited interval; no open source states it. Declared assumption.

  • trt_{r}1 h

    Duration of a roll and chuck replacement with the set-up check of the seams

    Szenario · Gleichverteilt 0,5 bis 2 h

    Deklarierte Annahme
  • Δco\Delta_{co}72 h

    Running time between two can-size changeovers

    Szenario · Gleichverteilt 24 bis 168 h

    Deklarierte Annahme
  • tcot_{co}2 h

    Duration of a can-size changeover (chucks

    Szenario · Gleichverteilt 1 bis 3 h

    Deklarierte Annahme
  • σy\sigma_y350 MPa

    Yield strength of the tinplate (end and body)

    Szenario · Gleichverteilt 250 bis 550 MPa

    Deklarierte Annahme

    Range of tinplate tempers; no open source with a quotable value was used.

  • DD80,96 mm

    Diameter of the No. 303 can (3 3/16 in)

    Szenario · Fest

    Deklarierte Annahme

    Can-size designation: first digit whole inches, next two digits sixteenths of an inch; 3 + 3/16 in = 80.96 mm.

  • θe\theta_e6,2832 radian

    Total plastic fold angle of the end curl while it becomes the cover hook (both operations)

    Szenario · Gleichverteilt 4,7124 bis 7,854 radian

    Deklarierte Annahme

    About 2 pi (range 1.5 pi to 2.5 pi): the curl is bent through about half a turn and flattened back; declared assumption.

  • θb\theta_b3,1416 radian

    Total plastic fold angle of the body flange while it becomes the body hook

    Szenario · Gleichverteilt 2,3562 bis 4,7124 radian

    Deklarierte Annahme

    About pi (range 0.75 pi to 1.5 pi); declared assumption.

  • mpm_p0,45 kg

    Mass of product per No. 303 can

    Szenario · Fest

    Deklarierte Annahme

8Vergleichswerte

Dokumentierte Werte aus offenen Quellen zur Prüfung der Obergrenzen; kein dokumentierter Wert darf die theoretische Grenze übertreffen.

In diesem Release nicht dokumentiert.

9Unvermeidbare Stillstände

Stillstände, die Physik oder Regulierung erzwingen; sie bestimmen die maximale Verfügbarkeit.
  • Replacement of worn seaming rolls and chucksVerifiziertes Zitat

    The groove profile of the seaming rolls wears with every seam; as it wears the seam lengthens and the overlap shrinks, so worn rolls must be replaced and the seams set up again. Interval and duration are declared scenario values.

    Wörtliches Zitat anzeigen
    Seam length is partly dependent on the roll groove profile and the degree of seaming roll wear.Metal can defects: identification and classification manual (öffnet in neuem Tab). Canadian Food Inspection Agency, Government of Canada, 2020. CFIA, Preventive controls for food: metal can defects
  • Can-size changeover (scenario stop: availability_scenario only)Deklarierte Annahme

    A new can size requires other chucks, rolls and feed parts and a new seam set-up; a decision of the product mix, not physics.

10Annahmen

  1. Body hook, cover hook and seam length are independent and normally distributed from can to can at one seaming station; the body hook is centred in its set-up aim and the cover hook aimed z_cap standard deviations above its operating minimum, the same capability margin that sets the body-hook dispersion from its operating limits.
  2. The overlap is the calculated overlap of 21 CFR 113.60, CH + BH + T - W; the guidance warns that it can over- or underestimate the optical overlap, and no adjustment factor is added. The internal seam length uses the factor 1.1 on the plate thicknesses of the teardown formula of body hook butting.
  3. A can is nonconforming when any of the three geometric criteria fails. Tightness (wrinkle rating), pressure ridge, juncture rating, cutovers, droops, false seams and compound defects are not modelled, so the quality ceiling is an upper bound.
  4. The seamer runs synchronised with the filler at its rated speed (performance factor 1); the seaming kinematics are declared, so the rate and the seaming time are reported without a theoretical label.
  5. Availability: the only stop forced by a physical mechanism is the replacement of rolls and chucks worn by seaming; no cleaning-in-place applies to the seamer, so the cleaning model is not used. Can-size changeovers are a product-mix decision and enter only availability_scenario and oee_scenario. Visual seam checks (every 30 minutes) are made on cans taken from the running line.
  6. Teardown cans are conforming product destroyed by the examination: they reduce the yield, not the quality factor. The plastic folding work is a rigid-perfectly-plastic lower bound (no friction, strain hardening, elastic springback or compound flow).

11Gültigkeitsbereich

  • Round three-piece sanitary food cans with steel ends of the 300-303 diameter group; other sizes, aluminium ends, two-piece and non-round cans have other guidelines.
  • Screw capping of bottles is not covered: its acceptance criteria (application and removal torque) are not stated in open regulations.

12Sensitivität

Elastizität: relative Änderung der Ergebnisgröße bei relativer Änderung jedes Parameters. Daneben steht die Spearman-Rangkorrelation aus den Monte-Carlo-Ziehungen.
  • Wˉ\bar WNominal seam length (width, height) set by the second-operation roll profile
    Elastizität -1,732Spearman-ρ -0,81
  • CHminCH_{min}Operating minimum of the cover (end) hook length, diameters 300 to 401
    Elastizität +0,100Spearman-ρ —
  • BHaim,hiBH_{aim,hi}Upper end of the set-up aim of the body hook length
    Elastizität +0,032Spearman-ρ —
  • pOLp_{OL}Minimum overlap as a share of the internal seam length (good manufacturing practice)
    Elastizität -0,030Spearman-ρ —
  • BHaim,loBH_{aim,lo}Lower end of the set-up aim of the body hook length, round sanitary cans of 207.5 to 401 diameter
    Elastizität +0,029Spearman-ρ —
  • TeT_eThickness of the end (cover) plate
    Elastizität +0,008Spearman-ρ +0,19
  • kkFactor applied to the plate thicknesses in the internal seam length (teardown formula of body hook butting)
    Elastizität +0,006Spearman-ρ —
  • zcapz_{cap}Capability margin of a capable seaming station: number of standard deviations between the aim and the operating limits of the hooks
    Elastizität +0,005Spearman-ρ +0,14
  • ΔBH\Delta_{BH}Half-width of the operating limit of the body hook length (.080 ± .008 in)
    Elastizität -0,002Spearman-ρ —
  • σW\sigma_WStandard deviation of the seam length
    Elastizität -0,002Spearman-ρ -0,18
  • tbt_bThickness of the body plate
    Elastizität +0,002Spearman-ρ +0,05
  • σCH\sigma_{CH}Standard deviation of the cover hook length of a capable seaming station
    Elastizität +0,001Spearman-ρ +0,16
  • Δr\Delta_{r}Running time between two replacements of worn seaming rolls and chucks
    Elastizität +0,001Spearman-ρ +0,23
  • trt_{r}Duration of a roll and chuck replacement with the set-up check of the seams
    Elastizität -0,001Spearman-ρ -0,15
  • pBHBp_{BHB}Minimum body hook butting (internal body hook length over internal seam length)
    Elastizität 0,000Spearman-ρ —
  • Größe steigt mit dem Parameter
  • Größe sinkt mit dem Parameter

13Validierungsprüfungen

Ein Modell wird nur veröffentlicht, wenn alle Prüfungen bestanden sind.
  • Dimensionsanalyse23 outputs converted to their declared unitsBestanden
  • Jeder zitierte Wert an seiner Quelle verifiziert10 verified, 0 failedBestanden
  • Kein dokumentierter Wert übertrifft die theoretische GrenzeBestanden
  • Obergrenzen in physikalischer ReihenfolgeBestanden
  • Anteile zwischen 0 und 1Bestanden

14Verlustursachen in dieser Operation

Wahrscheinlichkeit, dass jede Ursache als relevanter Verlust einer Linie dokumentiert ist, gepoolt über alle Segmente.

15Literatur

  1. 21 CFR Part 113 — Thermally Processed Low-Acid Foods Packaged in Hermetically Sealed Containers (4-1-25 Edition) (öffnet in neuem Tab). U.S. Government Publishing Office (Code of Federal Regulations), 2025. S. 29. 21 CFR 113 (2025)
  2. Metal can defects: identification and classification manual (öffnet in neuem Tab). Canadian Food Inspection Agency, Government of Canada, 2020. CFIA, Preventive controls for food: metal can defects
  3. Planning and engineering data 2. Fish canning (FAO Fisheries Circular No. 784), chapter 4: Processing operations (öffnet in neuem Tab). Food and Agriculture Organization of the United Nations, 1988. FAO Fisheries Circular No. 784, FIIU/C784(En)
  4. fda_bam_ch22a_2001