foratvise
Loslegen
Formen, Backen und Garen

Garen und Frittieren

Hot-water blanching of cut green beans before freezing

Validiertes ModellOEE-Grenze 0,828 [0,778–0,880]20.000 Monte-Carlo-Stichproben · Seed 20261115 · berechnet am 16. November 2026

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Garen und Frittieren kann höchstens 83 von je 100 geplanten Stunden nutzen. Der Rest entfällt auf Grenzen, die kein Werk vermeiden kann.

  1. 83höchstens nutzbar
  2. 17sind physikalische Grenze

Die drei Grenzen, die das festlegen

Laufzeit: bis 96 %

Der Rest sind Stillstände, die Physik oder Vorschrift erzwingen: Reinigung, Umrüsten, Abtauen.

Geschwindigkeit: bis 86 %

Wie nah an ihrer Höchstgeschwindigkeit sie laufen kann, ohne Produkt oder Anlage zu schädigen.

Gutprodukt: bis 100 %

Ein Teil des Produkts liegt auch bei gut beherrschtem Prozess außerhalb der Spezifikation.

Das technische Detail ansehen

Technisches Detail

Unsicherheitsintervalle, physikalische Modelle je Station und Quellen, für alle, die jede Zahl prüfen möchten.

1Szenario

Washed green beans (Phaseolus vulgaris), stemmed and cut into segments about 5 cm long and 9.5 mm in diameter, pass through a continuous hot-water blancher at about 92 °C and are then cooled and frozen. Blanching must inactivate the enzymes that would spoil colour, flavour and texture during frozen storage; peroxidase, the most heat-resistant of them, is the industrial indicator. The slowest-heating point of each bean, its centre, must receive the reference treatment. The same ceiling is applied to the blanching of other vegetables cut to a similar size as an approximation (derivation, section 7).

Herkunft der EingangsgrößenBerechnet2Deklarierte Annahme6Verifiziertes Zitat21

2Ergebnisse

Punktwert aus den Nominalparametern und 95-%-Intervall aus 20.000 Monte-Carlo-Ziehungen der unsicheren Parameter.
  • TheoretischThermodynamic minimum energy per kg of blanched beans0 kJ/kg
  • Heat absorbed by the beans without recovery (to the mass-average temperature at the design residence time)263 [215–281] kJ/kg
  • Beste verfügbare TechnikState-of-the-art on-site energy of blanching for frozen vegetables (DOE)205 kJ/kg
  • TypischCurrent typical on-site energy of blanching for frozen vegetables (DOE)372 kJ/kg
  • Heat absorbed by the beans over the state-of-the-art blanching energy1,29 [1,05–1,37]
  • Specific heat of the beans (Choi-Okos, USDA composition)3,9569 [3,9532–3,9583] kJ/kg/K
  • Thermal diffusivity of the beans1,55 × 10⁻⁷ [1,54 × 10⁻⁷–1,56 × 10⁻⁷] m²/s
  • Biot number h R / k of the mean bean7,61 [5,46–9,80]
  • Bean diameter for which the residence time is set (capability margin)11,7 [11,0–12,4] mm
  • TheoretischMinimum residence time: centre of the mean bean reaches the reference treatment194 [169–272] s
  • Residence time of the capable process (largest beans within the margin)225 [200–305] s
  • TypischTypical residence time of green beans in industrial blanchers500 s
  • TheoretischMaximum throughput per unit of blancher hold-up (kg/h per kg held)18,6 [13,2–21,3] 1/h
  • TypischThroughput per unit of hold-up at the typical residence time7,20 1/h
  • TheoretischMaximum yield (no mass has to leave the product)1,00
  • Share of beans whose centre stays below the reference treatment0,00135 [0,00026–0,00580]
  • TheoretischMaximum OEE quality factor0,9987 [0,9942–0,9997]
  • TheoretischMaximum availability (daily minimum cleaning and water reheating)0,964 [0,952–0,975]
  • TypischAvailability with a typical cleaning duration0,917 [0,892–0,941]
  • TheoretischMaximum performance factor: minimum residence time over the residence time of the capable process0,861 [0,809–0,914]
  • TheoretischPhysics-bounded OEE0,828 [0,778–0,880]

3Obergrenzen je Dimension

Jede Dimension zeigt die vom Modell berechneten Obergrenzen und, bei vergleichbaren Einheiten, dokumentierte Vergleichswerte. Farbe und Markerform kennzeichnen den Grenztyp im gesamten Orakel.
  • Theoretisch
  • Beste verfügbare Technik
  • Best dokumentiert
  • Typisch
Energie je ProdukteinheitkJ/kg · niedriger ist besser
  • TheoretischThermodynamic minimum energy per kg of blanched beans0 kJ/kg
  • TheoretischDOE bandwidth study: thermodynamic minimum of blanching for frozen vegetables set to zero (minimal chemical conversions) · Vergleichswert0 kJ/kg
  • Beste verfügbare TechnikState-of-the-art on-site energy of blanching for frozen vegetables (DOE)205 kJ/kg
  • TypischCurrent typical on-site energy of blanching for frozen vegetables (DOE)372 kJ/kg
Zyklus- oder Verweilzeits · niedriger ist besser
  • TheoretischMinimum residence time: centre of the mean bean reaches the reference treatment194 [169–272] s
  • TypischTypical residence time of green beans in industrial blanchers500 s
Durchsatz1/h · höher ist besser
  • TheoretischMaximum throughput per unit of blancher hold-up (kg/h per kg held)18,6 [13,2–21,3] 1/h
  • TypischThroughput per unit of hold-up at the typical residence time7,20 1/h
Ausbeutehöher ist besser
  • TheoretischMaximum yield (no mass has to leave the product)1,00
Qualitäthöher ist besser
  • TheoretischMaximum OEE quality factor0,9987 [0,9942–0,9997]
Verfügbarkeithöher ist besser
  • TheoretischMaximum availability (daily minimum cleaning and water reheating)0,964 [0,952–0,975]
  • TypischAvailability with a typical cleaning duration0,917 [0,892–0,941]
Leistunghöher ist besser
  • TheoretischMaximum performance factor: minimum residence time over the residence time of the capable process0,861 [0,809–0,914]
OEEhöher ist besser
  • TheoretischPhysics-bounded OEE0,828 [0,778–0,880]

4Verlustkaskade

Was jede Obergrenze von der nächsten trennt, von der physikalischen Grenze bis zum typischen Betrieb.
  1. TheoretischBeste verfügbare TechnikEnergie je Produkteinheit
    0 kJ/kg → 205 kJ/kg (Abstand 205 kJ/kg)

    The thermodynamic minimum is zero: blanching causes no significant net chemical change, and in the reversible limit the heat that warms the beans would be returned when they are cooled before freezing (the cooling water or air preheating the incoming beans). Without any recovery the blancher must deliver at least the heat the beans absorb, about two hundred and sixty kilojoules per kilogram for a rise from 25 °C to about 90 °C. The state-of-the-art level of the DOE study lies below that no-recovery heat, which is only possible with heat recovery: belt blanchers with water cooling preheat the incoming product with the heat released in the cooling zone, the technique the BREF calls the most energy-efficient.

  2. Beste verfügbare TechnikTypischEnergie je Produkteinheit
    205 kJ/kg → 372 kJ/kg (Abstand 167 kJ/kg)

    Current typical blanchers lose heat through open water surfaces and steam leaks at the product inlet and outlet (rotary valves and water seals reduce them), with the overflow of hot water that is replaced to limit the organic load, through uninsulated walls, and during idle running between products; they also heat the beans without recovering the heat removed in cooling.

  3. TheoretischTypischZyklus- oder Verweilzeit
    194 [169–272] s → 500 s (Abstand 306 s)

    The theoretical residence time brings the centre of the mean bean to the reference treatment with the documented bath coefficient. The capable process must cover the thickest beans (the capability margin of the diameter), and plants blanch longer still: the residence time is set for the coarsest grade and variety of the season, for the qualitative peroxidase test (which reacts to small residual activity of heat-stable isoenzymes) and for a safety margin against fluctuations of water temperature and load. The typical residence time of about 500 s is about two and a half times the theoretical time.

  4. TheoretischTypischQualität

    Beans thicker than the design diameter stay under-blanched. Real lines add colour and texture defects from over-blanching of thin beans, which share the residence time of the thick ones, and uneven residence in the blancher (back-mixing of the screw or the belt).

5Physikalisch begrenzte OEE

Die höchste OEE, die die Operation erreichen kann: Verfügbarkeit, Leistung und Qualität, begrenzt nur durch unvermeidbare Stillstände und physikalische Prozessfähigkeit.
Anteil der Belegungszeit, der nach jedem unvermeidbaren Verlust verbleibt. Die Achse beginnt bei 0,70.
  • Belegungszeit (ideal)
    1,000
  • Verfügbarkeit
    Faktor 0,964 [0,952–0,975]
    0,964 (−0,036)
  • Leistung
    Faktor 0,861 [0,809–0,914]
    0,829 (−0,134)
  • Qualität
    Faktor 0,9987 [0,9942–0,9997]
    0,828 (−0,001)
  • Physikalisch begrenzte OEE
    0,828 [0,778–0,880]

6Vollständige Herleitung

Massen- und Energiebilanzen, geschwindigkeitsbestimmender Schritt, Prozessfähigkeit und unvermeidbare Stillstände, mit Erläuterung jedes Terms.

Scope. Washed, stemmed green beans (Phaseolus vulgaris) cut into segments about 5 cm long and 9.5 mm in diameter pass through a continuous hot-water blancher at about 92 °C and are then cooled and frozen. This is the operation cooking_frying of the frozen-vegetable process. Blanching must inactivate the enzymes that would otherwise spoil colour, flavour and texture during frozen storage; peroxidase, the most heat-resistant of them, is the indicator used by industry. Symbols, values, units, uncertainty distributions and sources are listed in the parameter table generated from config/physics/cooking.yaml.

1. Mass balance — maximum yield

Blanching does not require any mass to leave the product. Hot water leaches some soluble solids and the tissue takes up or loses a little water, but neither is needed for the operation: a steam blancher or a shorter contact removes them without changing the purpose of the step. The yield ceiling is therefore

Ymax=1.Y_{max} = 1 .

Leaching losses, which grow with the blanching intensity, are technology losses; they are mass losses of conforming product and would be reported as yield, never inside the OEE.

2. Energy balance — minimum energy per unit of product

Thermodynamic minimum. Blanching causes no significant net chemical change. In the reversible limit the heat that warms the beans would be returned when they are cooled before freezing, for example by preheating the incoming beans with the cooling water. The thermodynamic minimum is zero, as the US DOE bandwidth study also sets for blanching of frozen vegetables ("set to zero due to minimal chemical conversions").

Heat absorbed by the product without recovery. A blancher that recovers nothing must deliver at least the heat the beans absorb. Per kilogram it is

qprod=cp (Tˉ(tdes)−T0),Tˉ=T∞−θˉ (T∞−T0),q_{prod} = c_p\,\big(\bar T(t_{des}) - T_0\big), \qquad \bar T = T_\infty - \bar\theta\,(T_\infty - T_0),

where T0T_0 is the entry temperature, T∞T_\infty the water temperature, θˉ\bar\theta the mass-average dimensionless temperature of the bean of design diameter at the end of the design residence time tdest_{des} (section 3), and cpc_p the specific heat. The specific heat, the density and the thermal conductivity come from the Choi–Okos composition model (meo.physics.foodprops) with the USDA composition of raw green beans: water 90.32 %, protein 1.83 %, fat 0.22 %, ash 0.66 %, carbohydrate by difference 6.97 % of which 2.7 % is dietary fibre (treated separately by Choi and Okos). With the point values cpc_p = 3.96 kJ kg⁻¹ K⁻¹ and qprodq_{prod} ≈ 263 kJ/kg.

The energy ceilings. Theoretical: 0. Best available technique: the state-of-the-art on-site intensity of blanching for frozen vegetables in the DOE study, 88 Btu/lb (205 kJ/kg). Typical: the current typical intensity of the same row, 160 Btu/lb (372 kJ/kg). The state-of-the-art value lies below the no-recovery heat qprodq_{prod} (the output product_heat_over_bat is their ratio), which is possible only with heat recovery: the BREF describes the belt blancher with water cooling, in which the heat released in the cooling zone preheats the incoming product, as the most energy-efficient blanching technique, with 0.09 t of steam per t of frozen vegetables. That steam figure is listed as a benchmark but not compared, because it is a mass of steam; at the latent heat of 7 bar steam it is of the same order as the DOE state of the art. The DOE practical minimum (75 Btu/lb) is a projection with technologies under research and carries no ceiling.

3. Rate-limiting step — minimum residence time

Heat conduction. A bean segment is about five times longer than it is thick, so it is treated, as in the source study, as an infinite cylinder of radius R=d/2R = d/2. Heat enters from the water through a surface coefficient hh and moves to the centre by conduction:

∂T∂t=αr∂∂r ⁣(r∂T∂r),−k∂T∂r∣R=h (TR−T∞),α=kρcp.\frac{\partial T}{\partial t} = \frac{\alpha}{r}\frac{\partial}{\partial r}\!\left(r\frac{\partial T}{\partial r}\right), \qquad -k\left.\frac{\partial T}{\partial r}\right|_{R} = h\,(T_R - T_\infty), \qquad \alpha = \frac{k}{\rho c_p}.

The exact solution (the Heisler–Fourier series of the cylinder) at the centre is

θc(t)=T∞−TcT∞−T0=∑n≥12J1(λn)λn [J02(λn)+J12(λn)]exp⁡ ⁣(−λn2 Fo),λnJ1(λn)=Bi J0(λn),\theta_c(t) = \frac{T_\infty - T_c}{T_\infty - T_0} = \sum_{n\ge1} \frac{2 J_1(\lambda_n)}{\lambda_n\,[J_0^2(\lambda_n) + J_1^2(\lambda_n)]}\exp\!\left(-\lambda_n^2\,Fo\right), \qquad \lambda_n J_1(\lambda_n) = Bi\,J_0(\lambda_n),

with the Fourier number Fo=αt/R2Fo = \alpha t/R^2, the ratio of the elapsed time to the time heat needs to diffuse over the radius, and the Biot number Bi=hR/kBi = hR/k, the ratio of the internal conduction resistance to the surface resistance. J0J_0 and J1J_1 are Bessel functions of the first kind; the eigenvalues λn\lambda_n are found by bisection between consecutive zeros of J1J_1 and J0J_0. The mass-average temperature used in section 2 has the coefficients 4Bi2/[λn2(λn2+Bi2)]4Bi^2/[\lambda_n^2(\lambda_n^2 + Bi^2)]. The bath coefficient hh = 1000 W m⁻² K⁻¹ was fitted by the source study to measured bean temperatures in hot-water baths; with it BiBi ≈ 7.6, so both the surface and the inside resist the heat flow and the centre lags clearly behind the water.

Enzyme criterion. Peroxidase inactivation is first order with an Arrhenius dependence on temperature, so any temperature history can be expressed as an equivalent time at a reference temperature TrefT_{ref}:

teq(t)=∫0texp⁡ ⁣[EaRg(1Tref−1Tc(t′))]dt′.t_{eq}(t) = \int_0^t \exp\!\left[\frac{E_a}{R_g}\left(\frac{1}{T_{ref}} - \frac{1}{T_c(t')}\right)\right]dt' .

The reference treatment is the example the BREF gives for blanching of vegetables, 75 °C for 5 min. The bean is blanched when its slowest-heating point, the centre, has received it: the minimum residence time tmint_{min} is the first time with teq=5t_{eq} = 5 min, found on a 2 s grid with linear interpolation. The activation energy is 57 kJ/mol, one of the values listed for green-bean peroxidase in the appendix of the source study; the uncertainty range spans the three green-bean values of that table, 48 to 77 kJ/mol. The same study fits 0.37 MJ/mol to its own data; with such a high activation energy the criterion becomes almost a threshold on the centre temperature and the minimum time is shorter. With the point values tmint_{min} ≈ 194 s for the mean bean.

Maximum throughput. A blancher of hold-up mhm_h (mass of beans inside) delivers at most mh/tminm_h/t_{min}, so the throughput per unit hold-up is 1/tmin1/t_{min} ≈ 18.6 h⁻¹; at the typical industrial residence time of about 500 s it is 7.2 h⁻¹. Two simplifications lengthen the computed time slightly: heat entering through the cut ends is neglected (exact for the middle of a long segment) and so is the inactivation during the cooling that follows. The time is therefore the conduction-limited minimum for the documented bath coefficient; a perfect surface (h→∞h \to \infty) would give a shorter, strictly physical limit that no water bath reaches.

4. Process capability — quality ceiling

The beans are not all of the same thickness: in the source study 150 segments had a mean diameter of 9.5 mm and ranged from 7.2 to 11.0 mm. The range of 150 normal draws is on average d2(150)d_2(150) = 5.30 standard deviations, so σd\sigma_d ≈ 0.72 mm. Thicker beans heat more slowly. A blancher has one residence time for all of them, so it is set for a design diameter

ddes=dˉ+z σd,d_{des} = \bar d + z\,\sigma_d,

and the beans thicker than ddesd_{des} stay under-blanched. They are the non-conforming units counted here:

Qmax=1−Φ(−z).Q_{max} = 1 - \Phi(-z).

With the margin zz = 3 (the same convention as the other models) ddesd_{des} ≈ 11.65 mm, the design residence time is tdest_{des} ≈ 225 s and QmaxQ_{max} = 0.99865. Over-blanching of the thin beans, which share the residence time of the thick ones, softens them and leaches more solids; it is a technology loss not counted in the bound.

5. Unavoidable stops — maximum availability

Leached solids, starch and plant debris accumulate in the blancher water and on the screw or belt; the water is drained and the blancher cleaned once per production day, and the refilled water must then be reheated to the blanching temperature before the first beans enter. No regulation in the registered sources fixes the interval (food-contact surfaces must be cleaned as often as necessary), so one cleaning per day is declared. The cleaning duration is linked to the minimum programme of the cleaning model (cip_time_min, about 22.5 min with its current result); that model is valid for recirculated pipe and plate circuits, so for an open blancher it is a lower bound, and a declared typical duration (1.5 h) gives availability_typical. With the reheating time thut_{hu}:

Amax=1−tcl+thutper=0.964.A_{max} = 1 - \frac{t_{cl} + t_{hu}}{t_{per}} = 0.964 .

6. Physics-bounded OEE

Scope of the bound. The theoretical label of OEEmaxOEE_{max} means physics-bounded under the declared scenario: the ceiling follows from the physics of the operation for the declared product, equipment and schedule, and it is a bound only conditional on those declarations. It follows the common definition of all models: AmaxA_{max} counts only stops required by regulation or forced by a physical mechanism, at their physical minimum duration, plus the start-up they force; PmaxP_{max} is the ratio of the physics-limited ideal cycle to the cycle of the capable process; QmaxQ_{max} is the share of conforming units, and mass losses of conforming product are reported only as yield.

The capability margin lengthens the residence time, as the lethality margin does in the retort model, so it acts through performance:

Pmax=tmin(dˉ)tmin(ddes)=0.861,OEEmax=Amax×Pmax×Qmax=0.828.P_{max} = \frac{t_{min}(\bar d)}{t_{min}(d_{des})} = 0.861, \qquad OEE_{max} = A_{max}\times P_{max}\times Q_{max} = 0.828 .

The point values and the Monte Carlo intervals over the declared uncertainty of every input are reported in the output table.

7. Assumptions, validity and use for other processes

See the assumption and validity lists generated from the configuration file. The most influential inputs (sensitivity table) are the water temperature, the activation energy, the bath coefficient and the bean diameter for the residence time, the capability margin and the diameter spread for performance, and the cleaning and reheating times for availability.

Use for other processes. The codebook assigns this operation to the frozen-vegetable process, whose products include many vegetables. The same ceiling is applied to them as an approximation when they are cut to pieces with a similar smallest dimension (diced carrots, peas of 8–10 mm): the conduction solution and the criterion are the same, but each vegetable has its own peroxidase kinetics, composition and size, and a sphere or cube conducts faster than a cylinder of the same thickness, so the bean ceiling is conservative for small cubes and spheres. Steam blanching has a much larger surface coefficient; with h→∞h \to \infty the residence time would approach the pure conduction limit and the ceiling would be somewhat higher.

References

  • van der Sman, R. G. M., Delbaere, S. M., Timmermans, R. A. H. (2026). Modeling of enzyme inactivation and quality changes during blanching of green beans. Current Research in Food Science, 12, 101424. doi:10.1016/j.crfs.2026.101424
  • U.S. Department of Agriculture, Agricultural Research Service. USDA National Nutrient Database for Standard Reference, Release 28, food group 11, record 11052 (Beans, snap, green, raw), 2015.
  • European Commission, Joint Research Centre. Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries, 2019 (section 8.2.2, blanching; Table 19.2).
  • U.S. Department of Energy. Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing, 2017 (Table A1-1, frozen vegetables).
  • Choi, Y. and Okos, M. R. (1986). Effects of temperature and composition on the thermal properties of food. In Food Engineering and Process Applications, Vol. 1, 93–101 (through the open reproductions cited by config/physics/food_properties.yaml).

7Parameter und Herkunft

Jede Eingangsgröße mit Wert, Einheit, Rolle, Unsicherheitsverteilung und Herkunft. Öffnen Sie ein Zitat, um die Quellenpassage zu lesen, die den Wert belegt.

8Vergleichswerte

Dokumentierte Werte aus offenen Quellen zur Prüfung der Obergrenzen; kein dokumentierter Wert darf die theoretische Grenze übertreffen.
VergleichswertObergrenzeWertHerkunft
DOE bandwidth study: thermodynamic minimum of blanching for frozen vegetables set to zero (minimal chemical conversions)
Wörtliches Zitat anzeigen
Blanching 20,639 160 88 75 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (öffnet in neuem Tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. S. 56. DOE/EE-1571; OSTI ID 1512366
Theoretisch0 Btu/lbVerifiziertes Zitat
DOE practical minimum of blanching for frozen vegetables (projected with technologies under research, not a documented achievement)
Wörtliches Zitat anzeigen
Blanching 20,639 160 88 75 0Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (öffnet in neuem Tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. S. 56. DOE/EE-1571; OSTI ID 1512366
—75 Btu/lbVerifiziertes Zitat
Steam of a belt blancher with water cooling, the most energy-efficient blanching technique of the BREF: 0.09 t of steam (7 bar) per t of frozen vegetables. Not compared: steam mass, not energy; at the latent heat of 7 bar steam (about 2.07 MJ/kg) it is about 190 kJ/kg, of the same order as the DOE state of the art
Wörtliches Zitat anzeigen
Steam (t/t frozen vegetables) 0.09Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 484. EUR 29978 EN; JRC118627; doi:10.2760/243911
—0,09 Verifiziertes Zitat
Shortest residence time in blanchers for fruits and vegetables in general (about 1 min). Not compared: it covers leafy and thin products whose conduction time is much shorter than that of a 9.5 mm bean
Wörtliches Zitat anzeigen
The residence time in the blancher can vary from approximately 1 to 5 minutes depending on the fruit or vegetable being blanched.Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 483. EUR 29978 EN; JRC118627; doi:10.2760/243911
Best dokumentiert1 minVerifiziertes Zitat
Longest residence time in blanchers for fruits and vegetables in general (about 5 min)
Wörtliches Zitat anzeigen
The residence time in the blancher can vary from approximately 1 to 5 minutes depending on the fruit or vegetable being blanched.Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 483. EUR 29978 EN; JRC118627; doi:10.2760/243911
Typisch5 minVerifiziertes Zitat

9Unvermeidbare Stillstände

Stillstände, die Physik oder Regulierung erzwingen; sie bestimmen die maximale Verfügbarkeit.
  • Daily cleaning of the blancherDeklarierte Annahme

    Leached solids, starch and plant debris accumulate in the blancher water and on the conveying screw or belt (blanching water carries a high organic load); the water is drained and the equipment cleaned once per production day. The minimum duration is the cleaning model's programme, a lower bound for an open blancher.

  • Reheating of the blancher water after cleaningDeklarierte Annahme

    The refilled water must reach the blanching temperature before the first beans enter; the time is the water mass times the temperature rise divided by the steam injection capacity.

10Annahmen

  1. Each bean segment is an infinite cylinder (length about five times the diameter, as in the source study); heat enters only through the curved surface, so the centre time is an upper estimate for the short end pieces and exact for the middle of long segments.
  2. Thermal properties are constant, evaluated with the Choi–Okos model at the mean of the entry and water temperatures from the USDA composition; the internal air of the pod and the seeds are not resolved.
  3. Peroxidase inactivation is first order with an Arrhenius temperature dependence, so the treatment is measured by the equivalent time at the reference temperature; the reference treatment (75 °C for 5 min at the slowest point) is the generic example of the BREF, not a value fitted to green beans. Inactivation during cooling after the blancher is neglected, which lengthens the computed time slightly.
  4. Bean diameters are normally distributed; the residence time is set for the diameter d + z sigma_d, beans beyond it are under-blanched and count as quality losses; the margin acts through performance (minimum residence time of the mean bean over that of the design bean). Leaching and water uptake are not losses required by the operation: yield_max = 1.
  5. Availability: the daily cleaning is counted at the minimum programme duration of the cleaning model (from_model link) and the reheating of the refilled water it forces at a declared duration. The cleaning model is valid for recirculated pipe and plate circuits; an open blancher with a screw or belt also needs draining and removal of debris, so the linked duration is a lower bound and a declared typical duration gives availability_typical. No regulation fixes the cleaning interval; one cleaning per production day is declared.

11Gültigkeitsbereich

  • Hot-water blanching of cut green beans of 7–11 mm diameter at 82–94 °C before freezing.
  • Approximation for other vegetables cut to pieces with a similar smallest dimension (diced carrots, peas); their own peroxidase kinetics and properties change the times.

12Sensitivität

Elastizität: relative Änderung der Ergebnisgröße bei relativer Änderung jedes Parameters. Daneben steht die Spearman-Rangkorrelation aus den Monte-Carlo-Ziehungen.
  • T∞T_\inftyTemperature of the blanching water
    Elastizität -0,366Spearman-ρ -0,49
  • TrefT_{ref}Temperature of the reference blanching treatment
    Elastizität +0,301Spearman-ρ —
  • σd\sigma_dStandard deviation of the bean diameter
    Elastizität -0,149Spearman-ρ -0,63
  • zmz_mCapability margin on the bean diameter, in standard deviations
    Elastizität -0,135Spearman-ρ -0,37
  • EaE_aActivation energy of the thermal inactivation of green-bean peroxidase
    Elastizität -0,104Spearman-ρ -0,38
  • treft_{ref}Holding time of the reference blanching treatment
    Elastizität +0,071Spearman-ρ —
  • tpert_{per}Production period between two cleanings (one production day)
    Elastizität +0,038Spearman-ρ —
  • thut_{hu}Reheating of the refilled blancher water to the blanching temperature
    Elastizität -0,022Spearman-ρ -0,20
  • T0T_0Temperature of the beans entering the blancher
    Elastizität +0,017Spearman-ρ +0,05
  • tclt_{cl}Minimum duration of the daily cleaning: physical minimum of the kinetic and displacement phases plus declared hold times (output cip_time_min of the cleaning model)
    Elastizität -0,016Spearman-ρ -0,07
  • ddMean diameter of the green-bean segments
    Elastizität +0,006Spearman-ρ —
  • xwx_wWater mass fraction of raw green beans
    Elastizität +0,001Spearman-ρ —
  • xc,diffx_{c,diff}Carbohydrate by difference (includes the fibre; the model uses carbohydrate minus fibre, as Choi and Okos treat fibre separately)
    Elastizität -0,001Spearman-ρ —
  • xpx_pProtein mass fraction
    Elastizität 0,000Spearman-ρ —
  • xfibx_{fib}Total dietary fibre mass fraction
    Elastizität 0,000Spearman-ρ —
  • xfx_fFat mass fraction
    Elastizität 0,000Spearman-ρ —
  • xax_aAsh mass fraction
    Elastizität 0,000Spearman-ρ —
  • hhSurface heat transfer coefficient of the hot-water bath
    Elastizität 0,000Spearman-ρ +0,02
  • Größe steigt mit dem Parameter
  • Größe sinkt mit dem Parameter

13Validierungsprüfungen

Ein Modell wird nur veröffentlicht, wenn alle Prüfungen bestanden sind.
  • Dimensionsanalyse21 outputs converted to their declared unitsBestanden
  • Jeder zitierte Wert an seiner Quelle verifiziert21 verified, 0 failedBestanden
  • Kein dokumentierter Wert übertrifft die theoretische GrenzeBestanden
  • Obergrenzen in physikalischer ReihenfolgeBestanden
  • Anteile zwischen 0 und 1Bestanden

14Verlustursachen in dieser Operation

Wahrscheinlichkeit, dass jede Ursache als relevanter Verlust einer Linie dokumentiert ist, gepoolt über alle Segmente.

15Literatur

  1. Modeling of enzyme inactivation and quality changes during blanching of green beans (van der Sman, Delbaere, Timmermans; Current Research in Food Science 12: 101424) (öffnet in neuem Tab). Elsevier (open access, CC BY 4.0); full text served by PubMed Central, 2026. doi:10.1016/j.crfs.2026.101424; PMC13217498
  2. USDA National Nutrient Database for Standard Reference, Release 28 (2015): Food Group 11, Vegetables and Vegetable Products (nutrient report) (öffnet in neuem Tab). U.S. Department of Agriculture, Agricultural Research Service, Nutrient Data Laboratory, 2015. S. 163. USDA SR28, food group 11 report (sr28fg11.pdf)
  3. Best Available Techniques (BAT) Reference Document for the Food, Drink and Milk Industries (öffnet in neuem Tab). European Commission, Joint Research Centre; Publications Office of the European Union, 2019. S. 785. EUR 29978 EN; JRC118627; doi:10.2760/243911
  4. Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Food and Beverage Manufacturing (öffnet in neuem Tab). U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Advanced Manufacturing Office, 2017. S. 56. DOE/EE-1571; OSTI ID 1512366
  5. doi:10.1016/j.crfs.2026.101424 — Bean geometry, bath heat transfer coefficient, initial and bath temperatures, typical industrial residence time and the activation energies of peroxidase inactivation.

Prozesse mit dieser Operation