Eingeschlossene Studie
Machine Learning, MRP, and Lean Tools as an Internal Innovation Strategy to Improve Efficiency in a Bottling Company
1Bibliografische Angaben
- Autoren
- Haydee Manuelo, Hellyn Ruiz, Martin Saenz-Moron, Anita Straujuma
- Jahr
- 2025
- Publikationsorgan
- LACCEI International Multiconference on Entrepreneurship, Innovation and Regional Development (LEIRD)
- Land
- Peru
- Segment
- Erfrischungsgetränke, abgefülltes Wasser und Säfte
- Prozessfamilie
- Abfüll- und Verpackungslinie
- Studientyp
- Vorher-nachher-Intervention
- Extraktionsumfang
- Volltext
- Umfang
- 1 Werke · 1 Linien · — Maschinen
- Beobachtungszeitraum
- 84 Tage
- Datenerhebung
- manual_logs
- Intervention
Umfeld laut Studie anzeigen
This format accounts for 94.48% of the company's total production volume, representing a critical point of intervention in its production management.
2Verzerrungsrisiko
Bewertet nach dem Schema des Protokolls: 2 geringe Bedenken, 1 einige Bedenken, 0 hohe Bedenken.
Gesamtpunktzahl 11Mittleres Risiko
| Kriterium | Punkte |
|---|---|
| Is the observed line, machine or plant described well enough to classify its segment, process and equipment?Product, process and equipment are all described. | 2 / 2 |
| Is the observation period long enough and reported?Period reported and at least 30 days of production (or at least 100 recorded events). | 2 / 2 |
| How were loss data collected?Manual logs or maintenance records with unknown completeness. | 1 / 2 |
| Are OEE, loading time and the loss categories defined explicitly?A standard definition is cited but its application is not shown. | 1 / 2 |
| Does the loss breakdown account for the total loss it claims to explain?Only the top causes are reported and the unexplained remainder can be computed. | 1 / 2 |
| Is there evidence of selective reporting of favourable results?Intervention study in which baseline and post-intervention periods differ in length or method. | 1 / 2 |
| Are the reported numbers internally consistent?Small inconsistencies (2 to 10 percentage points) or values that cannot be cross-checked. | 1 / 2 |
| Could conflicts of interest or the source of the data bias the result?Academic or independent study, or conflicts declared and unrelated to the result. | 2 / 2 |
3Extrahierte Daten
Jeder Datenpunkt mit seiner Einordnung und dem wörtlichen Zitat, das ihn belegt.
| Berichtete Ursache | Verlustkategorie | Kennzahl | Wert | Extraktion |
|---|---|---|---|---|
—sealing machineWörtliches Zitat anzeigen (Section V.B.3)After the implementation of autonomous maintenance, this value increased to 41.13 hours, representing an absolute improvement of 17.65 hours. | Anlagenausfall (Störungen) | Zeit zwischen Ereignissen | 41,1 h | Durch Schiedsentscheid |
—sealing machineWörtliches Zitat anzeigen (Section V.B.3)At the beginning of the study, the recorded MTBF was 23.48 hours. | Anlagenausfall (Störungen) | Zeit zwischen Ereignissen | 23,5 h | Durch Schiedsentscheid |
—Wörtliches Zitat anzeigen (Conclusions)The application of the proposed management model increased production efficiency from 75% to 86%, evidencing an 11% improvement that contributed to reducing bottlenecks and optimizing installed capacity. | none | OEE | 86,0 % | Beide Extraktionen übereinstimmend |
—Wörtliches Zitat anzeigen (Section III / Table I)Currently, the average efficiency of the production process is 75% (Table 1) | none | OEE | 75,0 % | Beide Extraktionen übereinstimmend |
—injection molding machineWörtliches Zitat anzeigen (Table VII)Availability (%) 89% 96% 97.17% | none | Verfügbarkeit | 97,2 % | Beide Extraktionen übereinstimmend |
—injection molding machineWörtliches Zitat anzeigen (Table VII)Availability (%) 89% 96% 97.17% | none | Verfügbarkeit | 89,0 % | Beide Extraktionen übereinstimmend |
lack of inputWörtliches Zitat anzeigen (Section III / Figure 1)Figure 1 shows that stoppages due to lack of input represent the main cause of loss, accounting for 49% of the total, followed by defects in the finished product and mechanical failures in the blow molding machines, which together amount to 83% of the total impact. | Organisatorische oder externe Stillstände (Material- oder Personalmangel, Ausfall der Versorgung) | Anteil an der Verlustzeit | 49,0 % | Einfache Extraktion |
—Wörtliches Zitat anzeigen (Section III / Figure 1)Figure 1 shows that stoppages due to lack of input represent the main cause of loss, accounting for 49% of the total, followed by defects in the finished product and mechanical failures in the blow molding machines, which together amount to 83% of the total impact. | Aus dem Bericht nicht klassifizierbar | Anteil an der Verlustzeit | 83,0 % | Einfache Extraktion |
reworkWörtliches Zitat anzeigen (Section V.B.2 / Table VI)In the initial process diagnosis, an inefficiency level of 19% was identified, reflecting high variability, rework, and bottlenecks. | Prozessfehler (Ausschuss und Nacharbeit) | Fehlerquote | 19,0 % | Einfache Extraktion |
reworkWörtliches Zitat anzeigen (Section V.B.2 / Table VI)With the validation of the pilot test, this value was reduced to 13%, representing a relative improvement of 32% compared to the initial condition. | Prozessfehler (Ausschuss und Nacharbeit) | Fehlerquote | 13,0 % | Einfache Extraktion |
—injection molding machineWörtliches Zitat anzeigen (Section V.B.3)During the development of the pilot test, a machine availability of 97.71% was achieved, exceeding the proposed target by 1.171%, as indicated in [7]. | none | Verfügbarkeit | 97,7 % | Einfache Extraktion |
—blow molding machinesWörtliches Zitat anzeigen (Conclusions)Autonomous maintenance raised the availability of blow moulding machines to 97.17% and improved the MTBF of the injection machine by 17.65 hours | none | Verfügbarkeit | 97,2 % | Einfache Extraktion |
—Wörtliches Zitat anzeigen (Table VI, STANDARDIZED WORK METRIC RESULTS)Standardized Work | Rework Rate (%) | 19% | 12% | 13% | Prozessfehler (Ausschuss und Nacharbeit) | Fehlerquote | 19,0 % | Einfache Extraktion |
lack of inputWörtliches Zitat anzeigen (Section V.B.1, Validation of MRP with Machine Learning)The average stockout rate in 2024 was 30.47%, significantly affecting production due to supply shortages. | Organisatorische oder externe Stillstände (Material- oder Personalmangel, Ausfall der Versorgung) | Anteil an der Verlustzeit | 30,5 % | Einfache Extraktion |
—Wörtliches Zitat anzeigen (Table VI, STANDARDIZED WORK METRIC RESULTS)Standardized Work | Rework Rate (%) | 19% | 12% | 13% | Prozessfehler (Ausschuss und Nacharbeit) | Fehlerquote | 13,0 % | Einfache Extraktion |
lack of inputWörtliches Zitat anzeigen (Section V.B.1, Validation of MRP with Machine Learning)With the validation of the MRP during the first quarter of 2025, the indicator decreased to 20.60% | Organisatorische oder externe Stillstände (Material- oder Personalmangel, Ausfall der Versorgung) | Anteil an der Verlustzeit | 20,6 % | Einfache Extraktion |
Beobachtungseinheiten
- Sealing machine · Verschließen und Falzen · Nach der Intervention
- Sealing machine · Verschließen und Falzen · Ausgangslage
- Whole plant · Gesamte Linie oder nicht spezifizierte Anlage · Nach der Intervention
- Whole plant · Gesamte Linie oder nicht spezifizierte Anlage · Ausgangslage
- Injection molding machine · Formen, Gießen und Dosieren · Nach der Intervention
- Injection molding machine · Formen, Gießen und Dosieren · Ausgangslage
- 8.5-liter bottling line · Gesamte Linie oder nicht spezifizierte Anlage · Ausgangslage
- 8.5-liter bottling line · Gesamte Linie oder nicht spezifizierte Anlage · Nach der Intervention
- Blow molding machines · Formen, Gießen und Dosieren · Nach der Intervention

